OmniSistem PR Design 150 User Manual

DESIGN 150

PR-11 50

This product manual contains important information about the safe installation and
use of this projector. Please read and follow these instructions carefully and keep this
manual in a safe place for future reference.

PR LIGHTING LTD

571 Yingbin Road Dashi Panyu Guangzhou 511430, China

http://www.pr-lighting.com

INDEX

SAFE USAGE OF THE PROJECTOR 3
INSTALLING THE PROJECTOR 4
FITTING THE LAMP 4
POWER CONNECTIONS 5
CONTROL CONNECTIONS 5
DMX TERMINATOR 6
DMX CONTROL CHANNEL FUNCTIONS 6
TO SET THE DMX START ADDRESS 6
SETUP OPTIONS 7
SETUP OPTIONS TABLE 7
STAND-ALONE MODE 8
MAINTENANCE 8
KEEPING THE PROJECTOR CLEAN 8
TROUBLESHOOTINGS 8
TECHNICAL DATA 9
LIGHT OUTPUT 10
ELECTRICAL DIAGRAM 10
COMPONENT ORDER CODES 11

Please note that as part of our ongoing commitment to continuous product development, specifications are subject to change
without notice. Whilst every care is taken in the preparation of this manual we reserve the right to change specifications in the
course of product improvement. The publishers cannot be held responsible for the accuracy of the information herein, or any
consequence arising from them.
Every apparatus is tested completely and packed properly by the manufacturer. Please make sure the packing and / or the
apparatus is in good condition before your installation and use. Should there be any damage caused by transportation, consult
your dealer and do not use the apparatus. But any damage caused by improper use will not be assumed by the manufacturer
and / or dealer.

THESE ITEMS ARE PACKED TOGETHER WITH THE PROJECTOR

Water proof 3-pin XLR plug (1 PCS)
Water proof 3-pin XLR socket (1 PCS)
Safety cord (1 PCS)
Barndoors (1 SET) (including 4 copper screws and 4 rubber washers, 4 screws and 4 flat washers)
This manual (1 PCS)
Optional: louvres (1 SET)

Thank you for purchasing our product Design 150, PR-1150.
This product manual contains important information about the safe installation and use of this
projector. Please read and follow these instructions carefully and keep this manual in a safe place for
future reference.
The Design 150 is a projector of innovative, compact, silent colour changing, capable of extraordinary
perforamances in terms of colour mixing, reliability and versatility. The projector can be used in
numerous environments and for the most various applications. The product complies to CE norms and
standards and uses international protocol DMX 512. Design 150 can be used as a stand-alone unit or
linked to a controller. The Design 150 are particularly suitable for television studios and theatres, stage
lighting, limelights, backdrops, inside or outside shops and shopping centres, sport and other cultural
applications, and so on.
The Design 150 features 3 kinds of colour filters for CYM colour mixing and 2 blads for shutter/open. It
can be setup easily with the touch-switches and a digital display screen.

ACCESSORIES

INTRODUCTION

2/12

Design 150 manual.doc

When unpacking and before disposing of the carton check there is no transportation damage before
using the projector. Keep the carton well for future possible transportation. Should there be any
damage caused by transportation, consult your dealer and do not use the apparatus.

The projector is suitable for indoor or outdoor use and is splash-proofed, IP65.

SAFE USAGE OF THE PROJECTOR

The projector is not designed or intended to be mounted directly on to inflammable surfaces.

The projector is only intended for installation, operation and maintenance by qualified personnel.
The projector must be installed in a location with adequate ventilation, at least 50cm from adjacent

surfaces. Be sure that no ventilation slots are blocked.
Do not project the beam onto inflammable surfaces, minimum distance is 3m.

Hot housing surface! Do not touch the housing of the projector with your hand during operation.
Avoid direct exposure to the light from the lamp. The light is harmful to the eye.
Do not attempt to dismantle and/or modify the projector in any way.
Electrical connection must only be carried out by qualified personnel.
Before installation, ensure that the voltage and frequency of power supply match the power

requirements of the projector.
It is essential that each projector is correctly earthed and that electrical installation conforms to all

relevant standards.
Do not connect this device to any dimmer pack.
Make sure that the power-cord is never crimped or damaged by sharp edges. Never let the power-

cord come into contact with other cables. Only handle the power-cord by the plug. Never pull out the
plug by tugging the power-cord.

Keep the lamp clean. Do not touch the lamp glass with bare hand.
The projector should always be installed with a secondary safety fixing. A safety cord is supplied for

this, it should be attached as shown in “installing the projector” section.
The lamp used in this projector is an 150W discharge lamp. After being switched off don’t attempt to

restart the projector until lamp has cooled, this will require approx 15 minutes. Switching the lamp on
and off at short intervals will reduce the life of both the lamp and the projector. But occasional breaks
will prolong the life of the lamp and projector.

Never run the projector without a lamp.
There are no user serviceable parts inside the projector, do not open the housing and never operate

the projector with the covers removed.

3m

Always disconnect from the mains, when the device is not in use or before cleaning it or
before attempting any maintenance work.

NOTE: PLEASE REMOVE THE SPONGE EFFECT LOCKING CYLINDER INSIDE THE
PROJECTOR BEFORE YOUR FIRST OPERATION!

(How to open the access cover please refer to “fitting the lamp” section)

3/12

Design 150 manual.doc

INSTALLING THE PROJECTOR

The unit was designed to make installation easy: it can be fitted on a floor, wall or ceiling as required
and will operate in any working position, as the head can be rotated through 90°.
Always ensure that the projector is firmly anchored to avoid vibration and slipping whilst functioning.
Always ensure that the structure to which you are attaching the projector is secure and is able to
support a weight of 17.6Kg for each Design 150. For safety the projector should have a secondary
fixing with a safety chain through the 2 secondary safety yokes on the both sides of the unit.
Note: For installing the barndoors, first install the 4 copper screws and sealing rubber washers in the
unit head, and then place the barndoors on the 4 copper screws and fasten them with 4 screws and
flat washes.

FITTING THE LAMP

Loosen the 2 M6 screws and then open the head cover as shown in the figure above.
Appear the lamp holder by letting the colour filters and blades aside from the center.
Plug the lamp into the lamp holder. Note: To avoid premature lamp failure, do not touch the lamp
glass with your fingers. If you touch the lamp during installation, clean it carefully with rubbing alcohol
and a clean, lint-free cloth before operation.
Close the cover and then tighen the 2 M6 screws.

NOTE: The HSD series are high pressure lamps with external igniters ( ). Care should always be

taken when handling these lamps. Always read the manufacturers "Instructions for use" enclosed with
the lamp.

4/12

Design 150 manual.doc