AL10 Series User Manual
www.omnisistem.com
Introduction
Thank you for purchasing Magic Box Wide Beam. Ma gic Box Wide Beam is a 1
channel DMX laser can be controlled via a standard DMX controller. It is a
lightweight, mini intel ligent fixture and is an ideal product for discos, clubs, exhibitions
and any place that need visionary effect. For safe operation, read this manual
before powering or installing the fixture, follow the safety precautions listed below, and
observe all warnings printed in this manual and on the fixture.
Safety Precautions
Do not spill liquids into or onto your unit. If this ever happens, disconnect the main
power immediately. Do not connect this unit to any dimmer pack.
Always disconnect from main power before making any type of connection.
Be sure to locate this unit in a place with adequate ventilation at least 15 cm from a
wall, and mount this unit in safe and stable matt er.
To prevent fire or shock hazard, do not expose this unit to a high temperature or
high humidity area. Please unplug unit when not in use.
Always keep combustible materials away from the fixture.
Class 3B laser should be mounted at or above 3 meters height. Project Class 3B
laser light above eye level. Do not project Class 3B Laser light on specular material.
The entrance to area where Class3B laser is used should be posted with
appropriate warning signs.
This unit is intended for in do o r use. Use of this unit outdoors voids all warranties.
Always refer service to a qualified technician. Never look directly into laser beam.
Occasional breaks are necessary to prevent breakdowns.
Caution - Use of controls or adjustments or performance of procedures other
than as specified herein may result in hazardous radiation exposure!
Set Up
Unpacking Magic Box Wide Beam comes with: 2 keys, 1 hanging bracket, 2
clamp levers, 2 washers, 1 power cord and 1 user manual. Unpack carefully and
be sure that no damage has occurred during shipping. If there is anything
missing or appear to be dam aged please contact your dealer.
Power Connection Be sure the source voltage in your area matches the
required voltage for your Magic Box Wide Beam before plugging your unit in.
Incorrect voltage selection will detrimentally affect the operation of this product.
DMX Cable Connection Magic Box Wide Beam is a one-channel DMX fixture t hat
can be operated with universal DMX controller. This unit and DMX controller
require a standard 3-pin XLR connector for data input and data output.
Installation/Mounting Magi c Box Wide Beam should be properly mounted by
using a suitable hanging cl amp and safety cable. Use in a well-ventilated are a.
Be sure no ventilation slots are blocked.
Specifications
Product Name Magic Box Wide Beam
Model No. AL10-05G
Laser Diode 4.9
Laser Color Green
Net Weight 4Kgs
Power AC 120V 50/60HZ
Classification 3R
Size (mm) L220 × W280 × H172
Fuse 20mm×2A
Housing Metal
Beam Divergence < 1.5 mrad
Operating temperature 18℃~25℃
Safety Label Position
Bottom
Front Panel
Identification label
Certification label
Warning label
Laser aperture & aperture label
Cleaning
Caution: Shut off the main power prior to clea ning unit.
Cleaning mirrors
Use a cotton swab and rubbing alcohol to clean the internal laser mirrors.
Remember to twirl slowly and press gently. Applying to much pressure can
break the mirrors.
Cleaning frequency depends on the environment in which the fixture operates.
Cleaning case
Use a soft cloth and normal glass cleaner to clean the casing. Be sure to dry all parts
before plugging the unit back in.
Operating Modes
Note: User must turn on key control to emit laser
1. Stand-Alone Operation (Auto, Sound Active Mode)
Auto mode
The unit runs built-in program to ch ange ef fect s autom atical ly. Set DIP switch
pin 10 to ON, other pins to OFF to run Auto mode
Sound Active mode
This unit has built-in program that w ill react to sound and music und er Sound
Active mode. Set all DIP switch pins to OFF to run Sound Active mode
2. Master-Slave Operation (Auto, Sound Active Mode)
This mode allows user to link up to 32 units to run the Master-Slave operation.
In the Master-Slave operation one unit will act as the controlling unit and the
others will react to the controlling unit. Daisy chain your units via the standard
XLR microphone cables in the following configuration: ‘O ut’ from the first unit to
‘In’ on the second, ‘Out’ from the second to ‘In’ on the third and so on.
Auto mode
To set the master: Set DI P switch pin 11 and 10 to ON, other pins to OFF.
To set the slaves: Set pin 1 to ON, other pins to OFF
Sound Active mode
To set the master: Set DIP switch pin 11 to ON, other pins to OFF.
To set the slaves: Set pin 1 to ON, other pins to OFF
3. DMX Operation
DMX operation gives the user freedom to create his/her own programs tailored
to their own individua l needs. To run this unit in DMX mode, connect the unit to
any standard DMX cont roller via XLR connectors. Please consult DMX
controller manual to determine address.
DMX Signal Levels
DMX 512 LEVEL 0~255 *Laser effect Control
230 ~ 255 Sound Active
225 ~ 229 Effect45
：
：
10 ~ 14 Effect2
5 ~ 9 Effect1
0 ~ 4 OFF
There are 45 effects preset between value5 to 229. Select them by changing signal
level as above introduction.
：
：
Operating Modes (Cont.)
Function Selection Chart
DIP SWITCHES CHART FUNCTION
1 2 3 4 5 6 7 8 9 10 11 12
OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF
OFF OFF OFF OFF OFF OFF OFF OFF OFF ON
SET SOUND / AUTO MODE ON
ON OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF
Control Panel Introduction
╳
SOUND MODE
╳
AUTO MODE
DMX MASTER
DMX SLAVE
SET ADDRESS OFF OFF
╳ / : Not Used
DMX MODE
Trouble Shooting
If there is no light from the unit, please check the main power supply and fuse.
If unit does not respond to DMX, please check the DMX cables are connected
properly and are wired correctly.
If unit does not response to the music please adjust the sound-active sensitivity
level by Sensitivity Adjustment Knob.
If the beam is fuzzy please refer to “cleaning“ section to clean the mirror first.
If problems cannot be solved please contact your dealer for service
Fuse Replacement
Always disconnect from main power supply before attempting to replace the fuse
Remove the old fuse from the holder and replace with the exa c t same type fuse.
Replacement with anyt hing other than the specified part m ay damage your unit.
Power Cord Connection
Fuse
Power Switch
Sensitivity Adjus tment Knob
Microphone
DMX In & Out
DIP Switch Pin
Interlock connector
Key control
Key control
ON OFF
Loading...