Omnimount Lift 42 User Manual

Lift 42

Motorized Flat Panel Lift System with
Universal Adapter.

10235ULN #

Lift 42 = L1-10235-PRO-101008vEPN #

INSTRUCTION MANUAL

IMAGES MAY DIFFER FROM ACTUAL PRODUCT.

W

ARNING –ENGLISH

 WARNING! SEVERE PERSONAL INJURY AND P RO P ERTY DAMAGE CAN

RESULT FROM IMPROPER INSTALLATION OR ASSEMBLY. READ THE
FOLLOWING WARNINGS BEFORE BEGINNING.

 If you do not understand the instructions or have any concerns or questions, please

contact a qualified installer. North America residents can contact OmniMount
customer service at 800.668.6848 or [e-mail].

 Do not install or assemble if the product or hardware is damaged or missing. If you

require replacement parts, contact OmniMount Customer Service at 800.668.6848 or
[e-mail]. International customers need to contact a local distributor for
assistance.

 Do not use this product for any application other than those specified by OmniMount.
 This product may contain moving parts. Use with caution.
 DO NOT EXCEED THE MAXIMUM WEIGHT CAPACITY FOR THIS PRODUCT.

OMINMOUNT PRODUCT WARRANTY

 This warranty applies to US Residents who purchase from an authorized OmniMount Dealer.

OmniMount products are covered against defects in materials and workmanship for 12 months.
OmniMount will repair or replace the defective component or product, at its sole discretion.

 To obtain warranty service, contact OmniMount customer service at 800.MOUNT.IT

(800.668.6848) or [e-mail]. You must supply a copy of your original receipt. If your
product must be shipped to OmniMount for inspection, you will be responsible for the shipping
charges. Replacement product shipped to you will be returned freight pre-paid.

 OmniMount disclaims any liability for modifications, improper installations, or installations over

the specified weight range. To the maximum extent permitted by law, OmniMount disclaims any
other warranties, expressed or implied, including warranties of fitness for a particular purpose
and warranties of mercha nta b il it y. Om niMo u nt wil l not be liable for any damages arising out of
the use of, or inability to use, OmniMount products. OmniMount bears no responsibility for
incidental or consequential damages. This includes, but is not limited to, any labor charges for
the repair of OmniMount products performed by anyone other than OmniMount.

 This warranty gives you specific legal rights, and you may also have other rights which vary

from state to state.

 Specifications are subject to change without prior notice.

WEIGHT CAPACITY

!

CAUTION

CAUTION: USE WITH PRODUCTS LARGER THAN THE MAXIMUM WEIGHT AND SIZE MAY
RESULT IN INSTABILITY CAUSING POSSIBLE INJURY. USER MUST REMOVE TELEVISION OR
OBJECT OFF THE BRACKET BEFORE ADJUSTING. MAXIMUM WEIGHT CAPACITY SUPERSEDES
/ OUTPLACES RECOMMENDED DIAGONAL MEASURED TELEVISION SIZE!!

DO NOT EXCEED MAXIMUM OF WEIGHT CAPACITY AND MAXIMUM RECOMMENDED DIAGONALLY

EN:

MEASURED TELEVISIONS SIZES!

Kilograms (KG)Pounds (LBS)MAXIMUM WEIGHT CAPACITY

56 (kg)125 (lbs)MAIN UNIT

2

Contents

Base Mount11
Lift Column12
Bayonet Bracket13
Screen Support14
Top Plate15
Control Box16
Remote Control17
IR Receiver/Control switch18
Corner brackets29

10

Universal Adapter1
Vertical Extension Rails and covers211
Screen Adapter112
Motor cable113
Power cable114

Contents

1

2

3

6

10

12

7

4

8

13 14

5

9

11

3

Contents

Monitor Kit:

Parts M-A through M-N are used to connect the TV to the universal
adapter. Spacers may be necessary for a proper fit with recessed mounting holes or to
allow access to TV inputs.

Monitor Kit L-U-vA

QtyPart #Pouch #

Philips screws M4 x 15mm4M-AM-A
Philips screws M4 x 35mm4M-BM-B
Philips screws M4 x 50mm4M-CM-C
Philips screws M5 x 15mm4M-DM-D
Philips screws M5 x 35mm4M-EM-E
Philips screws M5 x 50mm4M-FM-F
Philips screws M6 x 15mm4M-GM-G
Philips screws M6 x 35mm4M-HM-H
Philips screws M6 x 50mm4M-IM-I
Philips screws M8 x 15mm4M-JM-J
Philips screws M8 x 35mm4M-KM-K
Philips screws M8 x 50mm4M-LM-L
5/8" spacer4M-MM-M
3/4" spacer4M-NM-N

10235vB

Hex screws M6 x 20mm4O
Hex screws M6 x 30mm4P
Philips screws #10 x 3/4"4Q
Philips screws #8 x 3/4"4R
Hex screws 3/8-16 x 3/4"4S
2" x 1/4" Steel guide pins2T
Square washers4U
Felt corner cushions4V
Hex screws 1/4-20 x 1/2"4W
Allen wrench 7/32”1X
Allen wrench 5/32”1Y

Description

M-A

M-B

M-C

M-D

M-E

M-F

M-G

M-H

M-I

P

V

T

X

U

Y

S

W

O

Q R

M-J

M-K

M-L

M-M

M-N

4

Before Installation

 Prior to enclosure construction and lift assembly,

please read through the below warnings and
recommendations to ensure a successful
installation!

 PINCH POINT WARNING!

• Improper construction of lift enclosure can create dangerous pinch points. It is
the responsibility of the installer to ensure the intended use of this product does
not create hazardous pinch zones. Installation design should prevent users from
inserting objects between moving parts and fixed objects! Failure to do so may
result in serious injury or property damage.

 LIFT STABILITY:

• The Lift System should be installed into material at least ¾” thick on both the
back and bottom surfaces. The Lift Column is ONLY authorized and tested in a
vertical, upright orientation. For enclosures not secured structurally, be sure that
enclosure does not create a tip hazard when the lift is in the open position. DO
NOT MOUNT THE LIFT SYSTEM UPSI DE D OWN (AS IN A CEILING MOUNT),
OR SIDEWAYS (AS IN A LATERAL MOUNT)!

 ENCLOSURE DIMESIONS:

• Before constructing the enclosure carefully consider the dimensions of the TV to
be used and the lift mechanism. If possible “dry fit” (see next page) the TV to the
lift mechanism prior to building the enclosure to ensure proper fit and function.

 LARGE TV’S:

• With larger televisions the lift unit or lid may need extended to properly fit into
the enclosure. The most common applicati o n will be to use a spacer block (not
included) and corner brackets (part #12) to elevate the lift mechanism to allow
for greater TV height.

 FLOATING TOP:

• With floating top installations, it is important to center the lift within the enclosure
and center the cabinet top on the lift. With included hardware, the cabinet lid is
NOT designated as a weight bearing surface. For safety reasons the cabinet top
should be constructed in a “floating” configuration using the guide pins provided
to prevent pinch points. See guide pin template in appendix for recommendation.

5

Before Enclosure Construction!

 Assemble lift mechanism and connect the TV to be used in the

install to determine dimensions for the lift enclosure prior to
construction. Be sure to leave room for adjustments If
necessary. An out of cabinet assembly of the mechanism can
be done using steps 1,4,6,8,9 and 10 in order.

(D)

(H)

(W)

(H + 2”)

(W + 2”)

Minimum INTERIOR Dimensions

(D + 2”)

(H) Minimum Height

Height of lift in closed

position or Height of TV + 2”

(W) Minimum Width

Width of TV + 2”

This will allow 1 “ of clearance on either

side of the television.

NOTE:

longer rails spacers will be

needed above and below the

(D) Minimum Depth

Depth of TV + Depth of

Be very careful not to build

the enclosure too shallow.

The mount may not function

or damage to the TV could

For use with the

lift mechanism

Mount + 2”

occur

6