Omnimount AB2 HTS, AB2 User Manual
AB2/AB2 HTS INSTALLATION INSTRUCTIONS
Step 1 Identify parts
�
Mounting plate (1)
Screw covers
Extension
Adjusting knuckle
Mounting plate (2)
Speaker plate
These fasteners and tools are provided
AB2 HTS AB2 HTS
(1) (5) M4 X 12mm Phillips
pan head machine screw
(1) (5) M5 X 12mm Phillips pan
head machine screw
(2) (10) #12 X 3/4" Phillips pan
head self-tapping screw
(2) (10) #12 X 1-3/4'' Phillips pan
head self-tapping screw
(1) (5) 5/32'' Hex key
�
� �� � ��
Additional installation tools
Phillips Head Screw Driver
Pencil
Electric Drill
Drill Bits: 1/8'' drill bit for drywall
5/16'' masonry bit for cement wall applications
�
� � � ��� � ���� �
(2) (10) Plastic anchor
(1) (5) 8-32 X 5/8'' Phillips pan
head machine screw
(1) (5) Circular nut (PEM)
8-32 thread
(1) (5) 1/4-20 X 1" Phillips pan
head machine screw
(1) (2) 3/32'' Drill bit
1/8”
5/16'' mason bit
�
�
Step 2
Decide on location
Step 3 Installation of the wall plate
�
�
�
Mounting to solid concrete or cinder block.
Ceiling
�
Wall
Mounting to drywall.
1. Use the wall plate as a template and mark the screw hole locations onto the surface using a pencil.
2. Drill into the drywall with a 1/4'' drill bit. Insert the anchors into the hole as shown in fig. 3.
3. Secure with the #12 x 1-3/4'' screws, see fig. 4.
� ���� �
��� ���
��� ���
��� ���
�
Wall
1. Drill into the surface with a 3/16'' masonry drill bit 1-3/4" deep and insert the anchors into the holes as shown in Fig. 3
2. Secure wall plate with the #12 x 1-3/4" , see fig. 4.
�
� ���� �
��� ���
��� ���
�
�
�
��� ���
�
Step 3 Installation of wall plate (continued)
Mounting to solid wood or wood studs.
Drill a pilot hole into center of each location using 3/32" drill bit (provided),
Drill 1-1/4'' into stud. Attach the plate with two #12 x 1-3/4" wood screws.
fig. 3
Step 4 Installation of speaker plate onto speaker
1. Bose® speakers with 4MM or 5MM inserts.
��� ���
� � ��
fig. 2
fig. 6
wall
��� ���
fig. 4
wall
Step 5 Installation of adjusting knuckle
and extension.
�
Screw covers
Set screw locations
Set screw location
� � � �� �� �� � � �
�
� �
2. Speakers with single factory installed threaded insert.
� �
� �
3. Speakers with 2 installed 1/4''-20 or 6MM x 15MM threaded inserts.
�
1/4''-20 x 5/8'' or
6MM x 15MM
(not supplied)
�
Extension
OmniMount Systems, Inc.
The Pointe at South Mountain
8201 South 48th Street
Phoenix, Arizona 85044-5355
Toll free 1-800-MOUNT-IT
(480) 829-8000
Fax: (480)756-9000
email: info@omnimount.com
4. Speakers with a single keyhole in back.
Set screw location
Insert into keyhole and slide upward then tighten.
5. Speakers without mounting holes - wood cabinet only.
#12 x 3/4''
3/32'' drill bit
100% Replacement Warranty
Audio Basics products are engineered and manufactured to the highest standards. In the event that there are defects in materials,
workmanship, or missing parts, OmniMount Systems will, at its discretion, repair or replace your Audio Basics product. Claims that
are submitted must include either the sales slip or proof of purchase.
If OmniMount products are used for purposes other than their original intent, OmniMount Systems, its distributors and retailers shall
not be held responsible or liable for injuries or property damage, direct, indirect or consequential, which may arise from the inability
to use this product safely, properly, and in the manner for which it has been designed and manufactured.
This warranty does not apply to products which have been lost, damaged by misuse, abuse or accident, altered or repaired in any
way other than specified by OmniMount Systems, Inc.
This warranty is non-transferable.
For installation assistance please call our toll free help line at 1-800-MOUNT-IT
�
� �� �
Copyright 2004 OmniMount Systems, Inc.
All rights reserved. OmniMount products
are covered by patents issued and/or
pending. “OmniMount” is a registered
trademark of OmniMount Systems, Inc.
"Audio Basics" is a trademark of
OmniMount Systems, Inc.
AB-2 revision 2, 1/04 Part #1000254.
�
Loading...