Bead Ruptor 24
User Manual
BEAD RUPT
OR 24
This page was intentionally left blank.
Data herein has been veried and validated. It is believed adequate for the intended use of
the instrument. If the instrument or procedures are used for purposes over and above the
capabilities specied herein, conrmation of the validity and suitability should be obtained;
otherwise Omni International does not guarantee results and assumes no obligation or
liability. This publication is not a license to operate under, or a recommendation to infringe
upon, any process patents.
This product is warranted to be free from defects in material and workmanship for a period
of TWO YEARS from the date of delivery. Omni International will repair or replace and return
free of charge any part which is returned to its factory within said period, transportation
prepaid by user, and which is found upon inspection to have been defective in materials
or workmanship. This warranty does not include normal wear from use; it does not apply
to any instrument or parts which have been altered by anyone other than an employee
of Omni International nor to any instrument which has been damaged through accident,
negligence, failure to follow operating instructions, the use of electric currents or circuits
other than those specied on the plate axed to the instrument, misuse, or abuse. Omni
International reserves the right to change, alter, modify, or improve any of its instruments
without any obligation whatever to make corresponding changes to any instrument
previously sold or shipped.
THE FORGOING OBLIGATION IS IN LIEU OF ALL OBLIGATIONS AND LIABILITIES INCLUDING
NEGLIGENCE AND ALL WARRANTIES OF MERCHANTABILITY OR OTHERWISE, EXPRESSED
OR IMPLIED IN FACT OR BY LAW, AND STATE OUR ENTIRE AND EXCLUSIVE LIABILITY
AND BUYERS EXCLUSIVE REMEDY FOR ANY CLAIM OF DAMAGES IN CONNECTION WITH
THE SALE OR FURNISHING OF GOODS OR PARTS, THEIR DESIGN, SUITABILITY FOR USE,
INSTALLATION, OR OPERATION. OMNI INTERNATIONAL WILL IN NO EVENT BE LIABLE FOR
ANY SPECIAL OR CONSEQUENTIAL DAMAGES WHATSOEVER, AND THEIR LIABILITY UNDER
NO CIRCUMSTANCES WILL EXCEED THE CONTRACT PRICE FOR THE GOODS FOR WHICH
LIABILITY IS CLAIMED.
This product has been engineered for safety; however, basic safety precautions and
common sense must always be demonstrated when using any electrical product.
- DO NOT attempt to modify any part of this product.
- DO NOT allow the machine to be submerged in any liquid.
- DO NOT use in any setting other than an indoor laboratory.
- DO NOT plug power cord into an incorrect outlet or subject it to an incorrect voltage.
- Use this product only for its intended purpose.
- DO NOT use attachments not recommended by the manufacturer.
- DO NOT operate the product if it is damaged in any way.
- Keep this product away from heated surfaces.
- DO NOT modify the plug or cord that is provided. If the plug will not t the outlet, have
the proper outlet installed by a qualied electrician.
- DO NOT operate the product with the safety ground disconnected.
WARNING: Reduce the risk of unintentional starting; make sure the speed switch is in the
OFF position before plugging in the motor.
WARNING: Damaged or worn power cords should be repaired or replaced immediately by a
qualied electrician.
WARNING: Improper connection of the equipment can result in a risk of electric shock.
The Bead Ruptor 24 consists of the following:
Description Quantity
Bead Ruptor 24 Assembly 1
Power Cord 1
Spare Fuse 1
User Manual 1
Overview
Voltage
1.
2.
3.
4.
5.
6.
7.
8.
1. Lid
2. Drive Hub
3. Tube Carriage
4. Lid Latch
5. Keypad
6. 120V/220V Fuse
7. ON/O Switch
8. Power Cord Port
220 volts
- Remove Warning stickers from the back of the unit and check that the voltage matches the
voltage delivered by your electric power supply.
CAUTION: DO NOT connect the unit to the main power supply until correct voltage is selected.
- Plug the unit into power supply using the supplied power cord.
CAUTION: If the voltage supplied to the unit is higher than what is indicated on the back of the
unit, the electronics will be irreversibly damaged, voiding the warranty.
220 volts
220 volts
BEAD RUPT
OR 24
Loading Sample Tubes
Move the locking switch to the
“Lock” position.
CAUTION: DO NOT run
without moving the switch
to the “Lock” position.
A minimum of four tubes are required and must be spaced evenly*.
Screw down to secure tubes.
Close the lid until the locking handle
clicks into place.
CAUTION: The unitl will not run
without the lid fully closed.
3.
5.
7.
1.
4.
6.
Lock
Unlock
*
*
General Operation
Language Setting
Turn unit off. Press and hold while powering on unit.
to select.
Choose from French, English, German, Italian, or Spanish.
Programming Mode
- When the settings are entered press up or down to return to the program option.
- Press “Run” to start.
- At the end of the program “DONE” will be displayed Followed by “REMOVE SAMPLES”.
- If run is stopped system status will read “PROGRAM PAUSED”.
- Pause or Stop a run anytime by pressing the “STOP” button.
- Press “STOP” again to cancel current run.
PARAMETER OPERATING RANGE
S
Speed / Energy From 0.8 m/s to 8 m/s
T
Time
From 0:01 to 9:59 in increments of 1
second
C
Number of Cycles 1 to 10
D
Dwell/Pause between
Runs
0:00 to 9:59
PROG 01 20oC
S =4.50 C=02
T=0:10 D=0:10
READY
UP and DOWN - navigate through menu.
LEFT and RIGHT - adjust the parameters.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
1. Program Number
2. Speed
3. Cycle Time
4. Navigation Buttons
5. Parameters Adjustment Buttons
6. Processing Chamber Temperature
7. Number of Cycles
8. Time interval or Dwell between each cycle
9. Run Button
10. Stop Button
Troubleshooting
Error Cause Possible Solution
Unclosed Lid
The lid is not latched
properly
1. Check that nothing prevents the lid from closing.
2. Press lid and ensure the handle is locked properly.
Detection system is faulty
1. Turn o the unit.
2. Contact technical assistance.
Fan not working
No Power
1. Check main voltage
2. Check that the voltage of the unit matches
that being delivered by the main power supply.
3. Make sure that the unit is plugged in properly.
4. Check and replace fuses if blown.
Faulty Fan
1. Turn o the unit.
2. Contact technical support.
Display screen shows
incomplete or
unusual characters
CPU needs to be reset
1. Turn o the unit.
2. Wait 10 seconds.
3. Turn the unit back on.
No display on the screen
No Power
1. Check main voltage.
2. Check that the voltage of the unit matches
that being delivered by the main power supply.
3. Make sure the unit is plugged in properly.
4. Check and replace fuses if blown.
Faulty display screen
1. Turn o the unit.
2. Contact technical support.
One or several tubes are
not sealed tightly
The cap is not
properly sealed or the tube
is faulty
If dangerous or potentially dangerous sample
is contained in the tube, apply the proper
decontamination procedure.
Unit powers on with
a loud “BANG”
Motor control device
damaged due to incorrect
voltage selection
Return unit to Omni International for
replacement of motor control device.
Unit powers on but
motor does not turn
Incorrect voltage selected
Power o the unit and select appropriate
voltage. If problem persists, contact Omni
International for assistance.
Fingerplate lock is
dicult to disengage.
Knob position
Turn knob slightly counter-clockwise to release
tension.
Tube leakage
Speed is too high
High temperature or
pressure inside tubes
Reduce processing time or speed
DO NOT: attempt to service the Bead Ruptor 24 in a manner other than those discussed in
this manual. For any issue that is unsuccessfully corrected using this guide, please contact
your authorized dealer or call Omni International at 1-800-776-4431
PN: 03231 Rev. G
935C Cobb Place Blvd.
Kennesaw, GA 30144
800.776.4431 • 770.421.0058
www.omni-inc.com
Loading...