Omega Products SA2-RTD Installation Manual

GENERAL DESCRIPTION

The OMEGA SA2 Surface RTD (Resistance
Temperature Detector) is manufactured with a
flexible molded silicone sensor patch. This
sensor design utilizes a silicone based self­adhesive aluminium foil backing usable at
temperatures from -50 to 200°C (-58 to
392°F).

The SA2 sensors are manufactured in two
styles. The SA2C for Curved surfaces and the
SA2F for Flat surfaces. These sensors are
manufactured with 100 ohm Class B thin film
RTD elements whose resistance vs.
temperature characteristics conform to the
International Standard IEC 60751 (also
known as DIN Platinum RTDs). The sensors
also include four #26 AWG stranded nickel
plated copper extension wires that are PFA
insulated and jacketed. The RTD element is
bonded to the inner surface of the shell
adhesive foil backing to enhance thermal
transfer for faster response times.

OPERATING INSTRUCTIONS:

1. Prepare the surface to be measured by
cleaning it of oils and dirt. A general
solvent or alcohol will do. Doing this will
allow for better surface adhesion.

2. Peel the protective tape from the underside
of the mounting surface (see Figure 1).
(Take care not to get finger oils on the
silicone adhesive or mounting surfaces.)

3. Simply press the sensor onto the surface
and rub for maximum adhesion. It is

advised that the leads also be affixed to the
mounting surface to reduce the pull forces
on the wires and provide strain relief to the
sensor

4. Connect the extension wires to a
temperature measuring or controlling
device and you are ready to begin taking
temperature readings.

SPECIFICATIONS:

RTD Type: Platinum
Base Resistance:

100 Ohms at 0°C

Tolerance:

Class B = ±0.30+0.005t (t=temperature in °C)

Temperature Rating:

-50 to 200°C (-58 to 392°F)

Materials:
Pad:

Molded silicone rubber over aluminum foil
backing

Mounting Adhesive: silicone
Wire: #26 AWG stranded nickel plated

copper, PFA insulated and jacketed

Dimensions:
SA2C Pad:

50 x 15 x 2.5 mm (1.96 x 0.59 x 0.098")

SA2F Pad:

35 x 12 x 2.5 mm (1.38 x 0.47 x 0.098")

Wire Lengths Available:

1 m (40"), 2 m (80") and 3 m (120")

Figure 2. SA2F Pad

Figure 1. SA2C Pad

SA2-RTD

Molded Silicone Surface RTD Sensors

INSTRUCTION

SHEET

M0503D/0708

Shop online at: omega.com e-mail: [e-mail]
For latest product manuals: omegamanual.info

2.5

T/C WIRE

(40 INCHES)

1 METER

SILCONE

RUBBER

15

(0.59)

(0.098)

50

(1.96)

PROTECTIVE PAPER TAPE
OVER SILICONE ADHESIVE

DIMENSIONS: MM (IN)

12

(0.47)

2.5

(0.098)

35

(1.38)

SILICONE RUBBER HOUSING WITH SILICONE
ADHESIVE AND PROTECTIVE PAPER TAPE ON
MOUNTING SURFACE

1 METER

(40 INCHES)

T/C WIRE

It is the policy of OMEGA Engineering, Inc. to comply with all worldwide safety and EMC/EMI regulations that apply. OMEGA is constantly pursuing
certification of its products to the European New Approach Directives. OMEGA will add the CE mark to every appropriate device upon certification.

The information contained in this document is believed to be correct, but OMEGA accepts no liability for any errors it contains, and reserves the
right to alter specifications without notice.
WARNING: These products are not designed for use in, and should not be used for, human applications.

WARRANTY/DISCLAIMER

OMEGA ENGINEERING, INC. warrants this unit to be free of defects in materials and workmanship for a period of 13 months from
date of purchase. OMEGA’s WARRANTY adds an additional one (1) month grace period to the normal one (1) year product
warranty to cover handling and shipping time. This ensures that OMEGA’s customers receive maximum coverage on each
product.

If the unit malfunctions, it must be returned to the factory for evaluation. OMEGA’s Customer Service Department will issue an
Authorized Return (AR) number immediately upon phone or written request. Upon examination by OMEGA, if the unit is found to be
defective, it will be repaired or replaced at no charge. OMEGA’s WARRANTY does not apply to defects resulting from any action of the
purchaser, including but not limited to mishandling, improper interfacing, operation outside of design limits, improper repair, or
unauthorized modification. This WARRANTY is VOID if the unit shows evidence of having been tampered with or shows evidence of
having been damaged as a result of excessive corrosion; or current, heat, moisture or vibration; improper specification;
misapplication; misuse or other operating conditions outside of OMEGA’s control. Components in which wear is not warranted,
include but are not limited to contact points, fuses, and triacs.

OMEGA is pleased to offer suggestions on the use of its various products. However, OMEGA neither assumes responsibility
for any omissions or errors nor assumes liability for any damages that result from the use of its products in accordance with
information provided by OMEGA, either verbal or written. OMEGA warrants only that the parts manufactured by the
company will be as specified and free of defects. OMEGA MAKES NO OTHER WARRANTIES OR REPRESENTATIONS OF ANY
KIND WHATSOEVER, EXPRESSED OR IMPLIED, EXCEPT THAT OF TITLE, AND ALL IMPLIED WARRANTIES INCLUDING ANY
WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED. LIMITATION
OF LIABILITY: The remedies of purchaser set forth herein are exclusive, and the total liability of OMEGA with respect to this
order, whether based on contract, warranty, negligence, indemnification, strict liability or otherwise, shall not exceed the
purchase price of the component upon which liability is based. In no event shall OMEGA be liable for consequential,
incidental or special damages.

CONDITIONS: Equipment sold by OMEGA is not intended to be used, nor shall it be used: (1) as a “Basic Component” under 10 CFR
21 (NRC), used in or with any nuclear installation or activity; or (2) in medical applications or used on humans. Should any Product(s)
be used in or with any nuclear installation or activity, medical application, used on humans, or misused in any way, OMEGA assumes
no responsibility as set forth in our basic WARRANTY/ DISCLAIMER language, and, additionally, purchaser will indemnify OMEGA and
hold OMEGA harmless from any liability or damage whatsoever arising out of the use of the Product(s) in such a manner.

RETURN REQUESTS / INQUIRIES

Direct all warranty and repair requests/inquiries to the OMEGA Customer Service Department. BEFORE RETURNING ANY
PRODUCT(S) TO OMEGA, PURCHASER MUST OBTAIN AN AUTHORIZED RETURN (AR) NUMBER FROM OMEGA’S CUSTOMER
SERVICE DEPARTMENT (IN ORDER TO AVOID PROCESSING DELAYS). The assigned AR number should then be marked on the
outside of the return package and on any correspondence.

The purchaser is responsible for shipping charges, freight, insurance and proper packaging to prevent breakage in transit.

FOR WARRANTY

RETURNS, please have the following

information available BEFORE contacting OMEGA:

1. Purchase Order number under which the product was
PURCHASED,

2. Model and serial number of the product under warranty, and

3. Repair instructions and/or specific problems relative to the
product.

FOR NON-WARRANTY REPAIRS,

consult OMEGA for
current repair charges. Have the following information
available BEFORE contacting OMEGA:

1. Purchase Order number to cover the COST of the repair,

2. Model and serial number of the product, and

3. Repair instructions and/or specific problems relative to

the product.

OMEGA’s policy is to make running changes, not model changes, whenever an improvement is possible. This affords our customers the latest in
technology and engineering.

OMEGA is a registered trademark of OMEGA ENGINEERING, INC.
© Copyright 2008 OMEGA ENGINEERING, INC. All rights reserved. This document may not be copied, photocopied, reproduced, translated, or

reduced to any electronic medium or machine-readable form, in whole or in part, without the prior written consent of OMEGA ENGINEERING, INC.

Servicing North America:

U.S.A.: One Omega Drive, Box 4047

ISO 9001 Certified

Stamford, CT 06907-0047
Tel: [phone] FAX: [phone]
e-mail: [e-mail]

Canada: 976 Bergar

Laval (Quebec) H7L 5A1, Canada
Tel: [phone] FAX: [phone]
e-mail: [e-mail]

For immediate technical or application assistance:

U.S.A. and Sales Service: 1-800-826-6342/1-800-TC-OMEGA

®

Canada: Customer Service: 1-800-622-2378/1-800-622-BEST

®

Engineering Service: 1-800-872-9436/1-800-USA-WHEN

®

Mexico: En Espan˜ ol: [phone]-7803 e-mail:[e-mail]

FAX: [phone] [e-mail]

OMEGAnet®Online Service Internet e-mail

omega.com [e-mail]

Servicing Europe:

Czech Frystatska 184, 733 01 Karviná, Czech Republic
Republic: TEL: [phone]

FAX: [phone]
Tol Free: 0800-1-66342
e-mail: [e-mail]

Germany/ Daimlerstrasse 26, D-75392 Deckenpfronn, Germany
Austria: Tel: [phone]

FAX: [phone]
Toll Free in Germany: 0800 639 7678
e-mail: [e-mail]

United One Omega Drive, River Bend Technology Centre
Kingdom: Northbank, Irlam, Manchester

ISO 9001 Certified

M44 5BD United Kingdom
Tel: [phone]
FAX: [phone]
Toll Free in United Kingdom: 0800-488-488
e-mail: [e-mail]