Power SuPPlieS
For oPen Frame StePPer DriveS
OMPS Series
OMPS150A24, OMPS300A48
l Universal Input Voltage Range
from 85 to 265 Vac
l Built-In Active PFC Filter,
PF>0.95, Conforms to
EN61000-3-2
l Pending for Safety Approvals:
CE, CCC, UL/CSA/EN60950
l EMI: Conform to EN55011-B,
EN55022-B, FCC-B
l EMS: Conform to
EN61000-4-2, 3, 4, 5, 6, 8, 11
l LED Power Good Indicator
l Peak Current for
Motor Application
l 100% Full Load Burn-In Test,
High Performance,
High Reliability
l Compact Size, 15% Smaller
than Conventional Products
OMPS150A24
l 24V Output, Manually Adjustable
Output Voltage
l High Flexibility with 3 Optional
Connection Methods for Input/
Output: Horizontal or Vertical
Terminal Block or Connectors to
Fit Wire Harness
OMPS300A48
l 48V Output, Manually Adjustable
Output Voltage
l High Flexibility with 2 Optional
Connection Methods for Input/
Output: Horizontal or Vertical
Terminal Block
l Fan Speed Control by Output
Current to Extend Lifetime
l Remote Sense to Compensate
Wire/Connection Voltage Drop
Open-frame stepper drives require a
separate DC power supply for operation.
Omegamation offers two power supplies that
are matched for use with our open-frame
stepper drive selection: the OMPS150A24
and the OMPS300A48.
Both power supplies are switched-mode,
regulated DC power supplies with active PFC
filters. The OMPS150A24 is 24 Vdc, 6.3 A
(150 W)
while the OMPS300A48 is 48 Vdc,
6.7 A (300 W).
OMPS150A24 SPECIFICATIONS
Nominal Output Voltage: 24V
Maximum Output Current: 6.3 A
Peak Output Current: 9.5 A
Maximum Output Power: 151.2 W
Efficiency (Typical) (115/230 Vac)1:
82/85%
Input Voltage Range: 85 to 265 Vac
(47 to 63 Hz) or 120 to 370 Vdc
Input Current (Typical) (115/230 Vac)1:
1.8/0.9 A
Inrush Current (Typical): 16 A at
115 Vac, 32 A at 230 Vac, Ta = 25°C
(77°F), cold start
Harmonic Current: Compliance to
EN61000-3-2
Power Factor (Typical) (115/230 Vac)
0.99/0.95
Output Voltage Range: 21.6 to 26.4V
1
OMPS150A24
shown smaller
than actual size.
OMPS300A48
shown smaller
than actual size.
Ripple and Noise (115/230 Vac)
150 mV
Line Regulation2: 96 mV
Load Regulation2: 120 mV
Temperature Coefficient: Less than
0.02 %/°C
Over Current Protection3: 6.6/9.7 A
Over Voltage Protection4: 27.6 to 32.4V
Hold-Up Time (Typical)
(115/230 Vac)1: 20 ms
Leakage Current: 0.75 mA maximum,
0.25 mA (Typical) at 115 Vac, 0.5 mA
(Typical) at 230 Vac
Series Operation: Possible
Remote ON/OFF Control:
Option, CN3: 4 to 10V, Power ON;
0 to 0.8V, Power OFF
Operating Temperature: -10 to 70°C
(14 to 158°F)
Operating Humidity: 20 to 90% RH
(no dewdrop)
Storage Temperature: -30 to 85°C
(-22 to 185°F)
Storage Humidity: 10 to 95% RH
(no dewdrop)
Cooling Method: Convection cooling/
forced air cooling
Withstand Voltage:
Input - Output: 3.0 KVac (20 mA)
Input - FG: 2.0 KVac (20 mA)
Output - FG: 500 Vac (100 mA)
for 1 minute
:
Isolation Resistance: More than
100 MΩ at Ta = 25°C (77°F) and
70% RH, Output - FG: 500 Vdc
1, 2
:
D-37
115
(4.53)
11
(0.44)
11
(0.44)
65
(2.56)
64
(2.52)
50
(1.95)
25
(0.98)
14
(0.54)
57
(2.24)
117
(4.61)
215
(8.46)
50
(1.97)
Vibration: At no operating, 10 to 55 Hz,
10 min 1 cycle 19.6m/s2 constant, X, Y,
Z, 1 hour each
Safety: Pending, UL60950, CSA60950,
EN60950
EMI5: Compliance to FCC-Class B,
EN55011/EN55022-B,CISPR22 Class B
EMS Immunity5: Compliance to
EN61000-4-2, -3, -4, -5, -6, -8, -11
Weight (Typical): 620 g (21.87 oz)
Dimensions: 50 x 99 x 199 mm
(1.97 x 3.9 x 7.83")
1
At maximum output power, nominal input
voltage, Ta = 25°C (77°F).
2
Ripple and noise measured at bandwidth
of 20 MHz by using a 12” twisted pair-wire
terminated with 0.1uF and 47uF parallel
capacitors.
3
Constant current limit with automatic
recovery. Avoid operating at overload or
dead short for more than 60 seconds.
4
Shutdown output voltage, manual reset.
Re-power on to recover.
5
This power supply is considered a
component to be installed in final equipment
which should be re-confirmed to meet
EMC directives.
OMPS300A48 SPECIFICATIONS
Nominal Output Voltage: 48V
Maximum Output Current: 6.7 A
Peak Output Current: 8.7 A
Maximum Output Power: 321.6 W
Efficiency (Typical) (115/230 Vac)1:
80/85%
Input Voltage Range: 85 to 265 Vac
(47 to 63 Hz) or 120 to 370 Vdc
Input Current (Typical) (115/230 Vac)
3.6/1.8 A
Inrush Current (Typical): 20 A at
115 Vac, 32 A at 230 Vac, Ta = 25°C
(77°F), cold start
Harmonic Current: Compliance to
EN61000-3-2
Power Factor (Typical) (115/230 Vac)1:
0.99/0.95
Output Voltage Range: 43.2 to 52.8
Ripple and Noise (115/230 Vac)
1, 2
:
240 mV
Line Regulation2: 96 mV
Load Regulation2: 240 mV
Temperature Coefficient: Less than
0.02%/°C
Over Current Protection3: 7.0/8.9 A
Over Voltage Protection4: 55.2 to 64.8V
Over Temperature Protection: Yes
Hold-Up Time (Typical)
(115/230 Vac)1: 20 ms
Leakage Current: 0.75 mA maximum,
0.25 mA (typical) at 115 Vac, 0.5 mA
(typical) at 230 Vac
Series Operation: Yes
Remote ON/OFF Control:
Option, CN2: 4 to 10V, power ON;
0 to 0.8V, power OFF
Remote Sensing: Option
Operating Temperature: -10 to 65°C
(14 to 149°F)
Operating Humidity: 20 to 90% RH
(no dewdrop)
Storage Temperature: -30 to 85°C
(-22 to 185°F)
Storage Humidity: 10 to 95% RH
(no dewdrop)
1
:
Cooling Method:
Forced air by blower fan
Withstand Voltage:
Input - Output: 3.0 KVac (20 mA)
Input - FG: 2.0 KVac (20 mA)
Output - FG: 500 Vac (100 mA)
for 1 minute
Isolation Resistance: More than 100M
Ω at Ta = 25°C (77°F) and 70% RH,
Output - FG: 500 Vdc
Vibration: At no operating, 10 to 55 Hz,
10 min 1 cycle 19.6 m/s2 constant, X, Y,
Z, 1 hour each
Safety: Pending, UL60950, CSA60950,
EN60950
EMI5: Compliance to FCC-Class B,
EN55011/EN55022-B,CISPR22 Class B
EMS Immunity5: Compliance to
EN61000-4-2, -3, -4, -5, -6, -8, -11
Weight (Typical): 900 g (31.75 oz)
Dimensions: 50 x 115 x 215 mm
(1.97 x 4.53 x 8.46")
1
At maximum output power, nominal input
voltage, Ta = 25°C (77°F).
2
Ripple and noise measured at bandwidth
of 20 MHz by using a 12" twisted pair-wire
terminated with 0.1uF and 47uF parallel
capacitors.
3
Constant current limit with automatic
recovery. Avoid operating at overload or
dead short for more than 60 seconds.
4
Shutdown output voltage, manual reset.
Re-power on to recover.
5
This power supply is considered a
component to be installed in final equipment
which should be re-confirmed to meet EMC
directives.
D
Drives and Motors
OMPS150A24OMPS300A48
50
(1.97)
25
(0.98)
(1.65)
(1.58)
40
(1.58)
Dimensions: mm (inch)
D-38
199
(7.83)
42
40
65
(2.56)
117
(4.61)
45
(1.77)
50
(1.95)
(3.90)
25
(0.98)
99
12
(0.49)
V+
V-
VIN
+
_
VOUT
+
_
red
blk blk
N
L
GND
LN
Chassis Gnd
Gnd
screw
10 ohm
50 watt
4700 mfd
100V
Power Supply
RC050
ST DRIVE
V+
V-
A+
A-
B+
B-
STEP
MOTOR
Back panel
Internal
fuse
F1
Optional
connections
available on
some motors
F1 fuse should be sized at 1.5 times the input current
rating of the power supply, slo blo type.
F2 fuse : refer to ST hardware manual for appropriate size
F2
OMRC-050
l Wide Input Voltage Range
l Regeneration Present LED
l Power LED
OMRC-050 Regen Clamp –
For Stepper Drive Power
Supply Protection
There is a special consideration if the
power supply voltage will be at or near the
maximum voltage rating of the drive. If the
motor will be rapidly decelerating a large
inertial load from a high speed, care has to
be taken to absorb the returned energy. The
energy stored in the momentum of the load
must be removed during deceleration and be
safely dissipated. Because of its efficiency,
the drive has no means of dissipating this
energy so it returns it to the power supply.
In effect, instead of drawing current from the
power supply, the drive becomes a source of
current itself. This current may then charge
the power supply capacitor to destructive
voltage levels; this condition is commonly
known as motor regeneration. The
OMRC-050 Regen Clamp is designed
to protect your power supply from
regeneration, and is recommended when
your motor application exceeds the following
conditions:
NEMA 17 motors @ speeds > 30 rps
NEMA 23 motors @ speeds > 10 rps
NEMA 34 motors @ speeds > 4 rps
Motor deceleration rate > 100 rps
OMRC-050 shown
close to actual size.
Power Wiring Diagram for ST Drive with OMRC-050 Regen Clamp
SPECIFICATIONS
Input Voltage Range: 24 to 80 Vdc
Continuous Input Power: 50 W
Peak Input Power: 800 W
Dimensions: 76.2 x 101.6 x 57.15 mm
(3 x 4 x 2.25")
To Order Visit omega.com/ps_series for Pricing and Details
MODEL NO. DESCRIPTION
OMPS150A24 24V, 6.3 A power supply with active PFC filter
OMPS300A48 48V, 6.7 A power supply with active PFC filter
ACCESSORIES
MODEL NO. DESCRIPTION
OMRC-050 Regeneration clamp, 24 to 80 Vdc
POWER CORD-SE AC power cord with stripped end termination
POWER CORD-SE-M16 2.4 m (8') power cord with M16 cable gland strain relief, 3x16 AWG, 250 Vac max
Ordering Examples: OMPS300A48, 48V, 6.7 A power supply with active PFC filter, and OMRC-050, regen clamp.
OMPS150A24, 24V, 6.3 A power supply with active PFC filter.
D-39
Loading...