Omega Products OM-80 Installation Manual

omega.com

e-mail: [e-mail]

For latest product manuals:

omegamanual.info

OM-80 SERIES

Miniature RFID Data Loggers

Shop online at

User’s Guide

MADE IN

Servicing North America:

U.S.A.: Omega Engineering, Inc., One Omega Drive, P.O. Box 4047

ISO 9001 Certified Stamford, CT 06907-0047 USA

Toll Free: 1-800-826-6342 TEL: [phone]
FAX: [phone] e-mail: [e-mail]

Canada: 976 Bergar

Laval (Quebec), H7L 5A1 Canada
Toll-Free: 1-800-826-6342 TEL: [phone]
FAX: [phone] e-mail: [e-mail]

For immediate technical or application assistance:

U.S.A. and Canada: Sales Service: 1-800-826-6342/1-800-TC-OMEGA

®

Customer Service: 1-800-622-2378/1-800-622-BEST

®

Engineering Service: 1-800-872-9436/1-800-USA-WHEN

®

Mexico/ En Español: 001 [phone] FAX: [phone]
Latin America [e-mail] e-mail: [e-mail]

Servicing Europe:

Benelux: Managed by the United Kingdom Office

Toll-Free: 0800 099 3344 TEL: [phone]
FAX: [phone] e-mail: [e-mail]

Czech Republic: Frystatska 184

733 01 Karviná, Czech Republic
Toll-Free: 0800-1-66342 TEL: [phone]
FAX: [phone] e-mail: [e-mail]

France: Managed by the United Kingdom Office

Toll-Free: 0800 466 342 TEL: [phone]
FAX: [phone] e-mail: [e-mail]

Germany/Austria: Daimlerstrasse 26

D-75392 Deckenpfronn, Germany
Toll-Free: 0800 6397678 TEL: [phone]
FAX: [phone] e-mail: [e-mail]

United Kingdom: OMEGA Engineering Ltd.

ISO 9001 Certified One Omega Drive, River Bend Technology Centre, Northbank

Irlam, Manchester M44 5BD United Kingdom
Toll-Free: 0800-488-488 TEL: [phone]
FAX: [phone] e-mail: [e-mail]

OMEGAnet®Online Service Internet e-mail

omega.com [e-mail]

It is the policy of OMEGA Engineering, Inc. to comply with all worldwide safety and EMC/EMI
regulations that apply. OMEGA is constantly pursuing certification of its products to the European New
Approach Directives. OMEGA will add the CE mark to every appropriate device upon certification.

The information contained in this document is believed to be correct, but OMEGA accepts no liability for any
errors it contains, and reserves the right to alter specifications without notice.
WARNING: These products are not designed for use in, and should not be used for, human applications.

Table of Contents

Section Page

Section 1 Introduction ......................................................................................... 1-1

1.1 Precautions ................................................................................................. 1-1

1.2 Safety Warnings and IEC Symbols ......................................................... 1-2

1.3 Statement on FCC and CE Marking ....................................................... 1-2

1.4 Product Labeling ....................................................................................... 1-3

Section 2 Hardware .............................................................................................. 2-1

2.1 Package Inspection ................................................................................... 2-1

2.2 Included Items ........................................................................................... 2-1

Section 3 Software ................................................................................................ 3-1

3.1 Getting Started ........................................................................................... 3-1

3.2 Software Installation ................................................................................. 3-1

3.3 USB Driver Installation ............................................................................ 3-3

3.4 OM-80 Series Data Logging Software .................................................... 3-6

Section 4 Hardware Installation ........................................................................ 4-1

Section 5 Tag Configuration/Operation ........................................................... 5-1

5.1 Tag Information ......................................................................................... 5-1

5.2 Configuring Tag Settings ......................................................................... 5-3

5.3 Logging Data ............................................................................................. 5-5

5.4 Retrieving Data .......................................................................................... 5-5

Section 6 Calibration ........................................................................................... 6-1

Section 7 Troubleshooting .................................................................................. 7-1

7.1 Tag Troubleshooting ................................................................................. 7-1

7.2 Reader Troubleshooting ........................................................................... 7-1

Section 8 Service ................................................................................................... 8-1

Section 9 Specifications ...................................................................................... 9-1

Section 10 Approvals & Regulatory Compliance .........................................10-1

10.1 FCC (Domestic Use: USA & Canada) ................................................. 10-1

10.2 International Usage & CE Marking (Pending) ................................. 10-1

10.3 CE Declaration of Conformity (DOC) ................................................ 10-1

10.4 ESD Susceptibility ................................................................................. 10-1

i

OM-80 Series Miniature RFID Data Loggers

List of Figures

Section Figure Description .............................................................. Page

Section 1 1-1 IEC Symbols ............................................................... 1-2

1-2 OM-84 Tag Label ....................................................... 1-3

1-3 OM-80-RD1 Reader Top Label ................................ 1-3

1-4 OM-80-RD1 Reader Bottom Label .......................... 1-3

Section 3 3-1 Welcome Screen ......................................................... 3-1

3-2 License Agreement Screen ....................................... 3-2

3-3 Choose Install Location ............................................ 3-2

3-4 Installation Complete Screen ................................... 3-3

3-5 Welcome To The New Found

Hardware Wizard Screen ......................................... 3-4

3-6 Install Software Automatically Wizard Screen ..... 3-5

3-7 Completing The New Found

Hardware Wizard Screen ......................................... 3-5

3-8 Launch Data Logging Software .............................. 3-6

3-9 OM-84 Data Logging Program ................................ 3-7

3-10 Reader Tab .................................................................. 3-8

3-11 Data Display Graph .................................................. 3-9

3-12 Data Display Table .................................................... 3-9

Section 5 5-1 Tag Information Tab .................................................. 5-1

5-2 Tag Settings Tab ......................................................... 5-3

Section 6 6-1 Temperature Calibration Window .......................... 6-1

6-2 Remove Tag Window ............................................... 6-1

6-3 Calibration Complete Window ............................... 6-2

ii

OM-80 Series Miniature RFID Data Loggers

Section 1 - Introduction

Please read this manual completely before unpacking and operating your
miniature RFID data logger and reader system. It’s important read and follow all
notes, cautions, warnings and safety precautions before operating this device.
“Device” referrers to your data logger tag and reader.

Small, simple and affordable, the OM-80 series of data loggers measure and
record temperature at a user specified interval ranging from 1 second to over 9
hours. The tag is equipped with a one-button, three-LED user interface. The
start/status button can be used to activate the tag or check on the tag's status.
Two of the LEDs are used to indicate whether the tag has measured
temperatures that exceed programmable upper and lower temperature limits.
The third LED is used to indicate the tag's status through a series of blinks.

The tag is configured using a reader and PC user software to operate in one of
two modes:

ALARM CLOCK MODE

The tag begins collecting data at a prescribed time.

DELAY MODE

The tag begins collecting data after a specified delay from when the button is
pressed.

Once the tag has finished collecting data or in the highly unlikely event that it
loses power, the tag must be presented to reader/host software to download the
data and re-configure it for another data collection run. The tag can only collect
one series of temperature readings at time. The tag cannot be started, then halted
and later re-started, without intervention of the host software.

The OM-80 reader/host software requires no programming skills, and enables
you to effortlessly select a sample interval, specify a TAG ID, and initiate the
start of data collection. The data logger can be configured and ready to use in
just moments. In addition, all data can be saved in a format easily compatible
with spreadsheet applications such as Microsoft Excel. It is our goal to bring you
accurate, low-cost, easy-to-use data loggers that will easily integrate into your
working environment. To better serve you and understand your needs, we
welcome and appreciate your feedback.

1.1 Precautions

• This device is not designed for use in any medical or nuclear applications.

• Do not operate this device in flammable or explosive environments.

• Never operate with a power source other than the one recommended in this
manual.

• Do not operate this device outside of the recommended use outlined in this
manual.

There are no user serviceable parts inside your device.
Attempting to repair or service your unit may void your
warranty:

1-1

Introduction

1

NOTE:

1.2 Safety Warnings and IEC Symbols

This device is marked with international safety and hazard symbols in
accordance with IEC standards. It is important to read and follow all precautions
and instructions in this manual before operating or commissioning this device as
it contains important information relating to safety and EMC. Failure to follow
all safety precautions may result in injury and or damage to your device. Use of
this device in a manner not specified will void your warranty

IEC Symbols Description

Caution, refer to accompanying documentation

EU’s Waste Electrical and Electronic Equipment Compliance

Figure 1-1 IEC Symbols

OM-80 Series data loggers contain a lithium battery. Do not cut open, incinerate,
heat above 85°C, recharge, submerge under water or other liquid or expose the
battery to rain or excess humidity. Disposer per local regulations.

1.3 Statement on FCC and CE Marking

1.3.1 FCC Marking

FCC ID: WR3-OM80RD1 IC: 8205A-OM80RD1

This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions: 1.) This device may not cause harmful interference. 2.)
This device must accept any interference received, including interference that
may cause undesired operation.

1.3.2 CE Marking

It is the policy of OMEGA to comply with all worldwide safety and EMI/EMC
regulations that apply. OMEGA is constantly pursuing certification of its
products to the European New Approach Directives. OMEGA will add the CE
mark to every appropriate device upon certification. For additional information
see Section 11 - Approvals & Regulatory Compliance.

Introduction

1

1-2

1.4 Product Labeling

1.4.1 Tag Label

Figure 1-2. OM-84 Tag Label

1.4.2 Reader Labels

Figure 1-3. Reader Top Label OM-80-RD1

Figure 1-4. Reader Bottom Label OM-80-RD1

Introduction

1

1-3

START

HI ALARM

LOW ALARM

OMEGA ENGINEERING INC.

Stamford, Ct 06907

omega.com

Made in U.S.A.

!

Li

Li

CAUTION: Read Accompanying Documentation.

Not For Medical Use.

Range: -40 to 60 C (140 F)

13.56 MHz

STATUS

Contains Lithium Battery. Do not incinerate.

Always dispose of this product in a manner

consistent with local, regional and national

regulations. Do not recharge.

PATENT PENDING

NOMAD

®

RFID TEMPERATURE LOGGER

mini

Model: OM-84-TMP

®

13.56 MHZ

RFID TAG READER

PLACE TAG HERE

OM-80 SERIES

!

This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:

1) This device may not cause harmful interference;

2) This device must accept any interference received,
including interference that may cause undesired
operation.

FCC ID: WR3-OM80RD1
IC: 8205A-OM80RD1

OMEGA ENGINEERING, INC.
Stamford, CT 06907

Made in U.S.A. omega.com

®

Section 2 - Hardware

It is important that you read this manual completely and follow all safety
precautions before operating this instrument.

2.1 Package Inspection

Remove the packing list and verify that you have received all your equipment. If
you have any questions about the shipment, please call our Customer Service
Department at 1-800-622-2378 or 203-359-1660. We can also be reached on the
Internet at omega.com, e-mail: [e-mail]. When you receive the
shipment, inspect the container and equipment for any signs of damage. Note
any evidence of rough handling in transit. Immediately report any damage to
the shipping agent.

The carrier will not honor any damage claims unless all shipping material is
saved for inspection. After examining and removing contents, save packing
material and carton in the event reshipment is necessary.

2.2 Included Items

The following items are supplied in the box.

With kit OM-84-TMP-KIT:

• 5 temperature logging tags with factory replaceable battery

• 1 Benchtop USB tag reader

• 1 User Software CD

• 1 USB cable

• 1 Soft carrying case

• 1 Permanent marker

With kit OM-85-TMP-KIT:

• 5 temperature logging tags in hard plastic case with field replaceable battery

• 1 Benchtop USB tag reader

• 1 User Software CD

• 1 USB cable

• 1 Soft carrying case

• 1 Permanent marker

2-1

Hardware

2

Section 3 – Software

3.1 Getting Started

The following program files are included on the OM-80 Series User Software CD
supplied with kit. These files can also be downloaded from the omega.com
website should you misplace your CD.

• OM-80 Series Data Logging Program

• OM-80 Series Manual (pdf format)

• OM-80 Series Data Sheet (pdf format)

• OM-80-RD1 USB drivers

3.2 Software Installation

Insert the CD ROM labeled OMEGASOFT®OM-80 Series Data Logging Software
into your CD ROM drive. From the Windows Start menu, choose the Run
command and type d:\setup into the Open field and click OK. If your CD ROM
drive is not the D: drive, use the correct letter in the instructions above. You will
then see the welcome window as shown below.

Figure 3-1. Welcome to the Omega Engineering Data Loggin Application Setup Wizard

Click “Next” to continue the installation or “Cancel” to quit. When you click
Next the license agreement window will appear.

3-1

Software

3

Figure 3-2. License Agreement

Click “I Agree” to continue the installation or “Cancel” to quit.

Figure 3-3. Choose Install Location

This window allows you to specify a location for the application to be installed.
You can click Browse to choose another location or click Install to keep the
default location. After you click Install you should see a progress bar and then
the completing installation window as shown below. Click Finish to complete
the installation.

Software

3

3-2