Omega Products LVR-A6 User Manual

ECONOMICAL LIQUID LEVEL
FM
APPROVED
TRANSMITTERS
Suitable for Levels to Six Feet
LVR20/30 Series
$
650
Rugged SS Construction
4-20 mA or Resistance Output
1
4" Resolution
The OMEGA®LVR20 and LVR30 Series continuous liquid level sensors operate on a basic voltage divider network principle. As the float rises, a magnet in the float closes a series of reed switches in sequence which varies the tapped-off portion of the voltage divider resistor network. The LVR20 has the basic voltage divider output—the regulated DC voltage input equals the maximum voltage output. The LVR20 has a nominal 1,200 resistance; thus, with a 10 Vdc supply, 8.3 mA of current are required.
The OMEGA panel meters can be used to power and display the resistance from the LVR20; when relays are required, the DP25E-A meter can be used. For maximum accuracy, the readout device for the LVR20 should be zero and span adjusted after wiring is completed to compensate for any effects due to the resistance of the lead wires. The LVR20 can also be made intrinsically safe when used with OMEGA’s intrinsic safety barriers and when properly powered. The LVR30 Series is provided with a signal conditioner to provide a 4-20 mA output when powered by 10-30 Vdc. The LVR30 Series cannot be made intrinsically safe.
All LVR30 units are supplied with a J-box with screw terminal
®
DPF52 or DP24-E
connections. All LVR20 units are supplied without a J-box with 24 inches of bare wire coming out of the top of the unit with a 1⁄2 MNPT conduit connection. All LVR20 and LVR30 Series units can be wired for increasing output with either increasing or decreasing height of liquid; standard output is increasing output with increasing height. For other lengths, adaptor systems are available. They consist of two parts: the LVR-C coupling (2 x2FNPT) and an LVR-A pipe nipple (2 x2MNPT) of various lengths to change the insertion depth of the LVR20 or LVR30 sensor. When using the adaptors, a zero offset is introduced into the output signal which must be compensated for in the readout device (for example, the mA signal will not go down to 4 mA, nor will the voltage output go down to zero).
Retaining clip pliers are required to remove the float when using the adaptor system.
SPECIFICATIONS
Wetted Parts: 304 SS stem and
mounting, 316 SS float, 18-8 SS float stop
Liquid Temperature: -40 to 110°C (-40 to 230°F)
Minimum Liquid Specific Gravity:
0.75
Ambient Operating Temperature:
LVR20: -40 to 110°C (-40 to 230°F); LVR30: -15 to 71.1°C (5 to 160°F)
LVR30 Temperature Coefficient:
±0.00388%FS/°F
Storage Temperature:
LVR20: -40 to 110°C (-40 to 230°F); LVR30: -40 to 100°C (-40 to 212°F)
Max Operating Pressure: 300 psig Operating Voltage: LVR30: 10 to
40 Vdc; LVR20: 5 to 30 Vdc LVR30 Loop Impedance: (Volts in - 10)
x 46.66 = with 24 Vdc power, max loop impedance = 653 .
Connections: LVR30 is 2-wire; LVR20 is 3-wire
Accuracy: LVR30: 0.4% of full scale or
1
±
2", whichever is greater. LVR20: ±1⁄2"
Weights: LVR30–5 lbs. + LVR20–1 LVR-C–1
3
4 lbs. + 1⁄4 lb. per foot;
1
4 lbs.
1
4 lb. per foot;
LVR20 Supplied
Without J-box
LVR30 Series Shown Smaller Than Actual Size
Indicating Lengths from 1 to 6 Feet
K-15
DIMENSIONS FOR LVR20 AND LVR30
69.9
(2-3/4)
52.4 (2-1/16)
DIA. TYP
2 MNPT
C
Indicating
Length
Lowest
Level
Indicated
D
A
B
E
8 (5/16)
13 (1/2)
1/2 FNPT
J-Bo
x
Supplied
with LV R3 0
only
Highest
Level
Indicated
A: Float travel = indicating length +3⁄8" ±1⁄4" B: Stem length = indicating length + 39⁄16" ±1⁄16" C: Distance to float stop = 6.4 mm (1⁄4") ±1⁄16" D: 39.7 mm (19⁄16") E: 44.5 mm (13⁄4") (Assumes 1.0 S.G. Fluid)
Dimensions: mm (in)
Use the LVR20 and LVR30 transmitters with the DPF50 Series indicators. See section M for details.
Dimensions: mm (in)
150 lb 304 SS Coupling, 2 x 2 FNPT
Model No. Price LVR-C $40
LVR-A Pipe Nipples
LVR-C Coupling
Pipe Nipples, 304 SS, 150 lb fittings, 2 x 2 MNPT
Model No. Price Weight (lbs) Indicating Length Change LVR-A4 12 11⁄4 4" LVR-A5 20 11⁄2 5" LVR-A6 19 13⁄4 6" LVR-A7 30 2 7" LVR-A9 32 21⁄2 9" LVR-A11 37 3 11" LVR-A13 43 31⁄2 13"
MOST POPULAR MODELS HIGHLIGHTED!
To Order (Specify Model No.)
Voltage Divider
Isolated 4-20mA Output Voltage in = Voltage out Model No. Price Model No. Price Indicating Length LVR31 $775 LVR21 $650 1'
LVR32 925 LVR22 800 2' LVR33 1100 LVR23 950 3' LVR34 1250 LVR24 1100 4' LVR35 1400 LVR25 1250 5' LVR36 1550 LVR26 1400 6'
Ordering Examples: LVR31, 316 SS level sensor with mounted J-box and 0.3 m (1') indicating length, $775.
LVR22 is a 304 SS level sensor with 2 ft long indicating length, nominal 0-1200 ohm resistance change and a 2" MNPT mounting thread, $608.
K-16
K
FLOW
Loading...
+ 1 hidden pages