Page 1
M
M-X
EXTRA LARGE DISPLAY METER
FOR DIGITAL INPUT
LDPF63100 Series
$
696
LDPF63100, $696, shown smaller than actual size.
⻬ Large LED Display
Readable to 54 m (180')
⻬ Digital Input; Count and
Rate Input Serial Slave
⻬ Alarms, Analog Output,
and Communication
⻬ Programmable
User Inputs
⻬ Universal AC Powered
(85 to 250 Vac)
⻬ PC Software for Meter
Configuration
⻬ NEMA 4X (IP65)
The LDPF63100 display is a
versatile display that can increase
productivity by offering the plant
floor or production area a large
visual display of their current status.
Whether your measurement is rate,
count, or time. The LDPF63100 can
satisfy your requirement. The
displays accept various digital
inputs through the use of input
modules that allow the unit to adapt
to most any application. Additional
plug-in option cards can add alarms,
analog output, and communication/
bus capabilities, making the it a truly
intelligent panel meter.
SPECIFICATIONS
Display: 101 mm (4") red LED
6-Digit (-99999 to 999999)
Power Requirements: 85 to 250 Vac,
50/60 hz, 10 VA
Inputs A and B
DIP switch selectable to accept pulses
from a variety of sources including
switch contacts, TTL outputs, magnetic
pickups and all standard sensors.
Logic: Input trigger levels
V
IL
= 1.5V max; VIH= 3.75V min
Current Sinking: Internal 7.8 KΩ
pull-up to +12 Vdc, I
MAX
= 1.9 mA
Current Sourcing: Internal 3.9 KΩ
pull-down, 7.3 mA max @ 28 Vdc,
V
MAX
= 30 Vdc
Filter: Damping capacitor provided for
switch contact bounce. Limits input
frequency to 50 hz and input pulse
widths to 10 msec minimum
Magnetic Pickup
Sensitivity: 200 mV peak
Hysteresis: 100 mV
Input Impedance: 3.9 KΩ @ 60 hz
Max Input Voltage: ±40V peak,
30 Vrms
Dual Count Modes:
When any dual count mode is used,
then user inputs 1 and/or 2 will accept
the second signal of each signal pair.
The user inputs do not have the
Logic/Mag, High/Low Freq, and
Sink/Source input setup switches.
The user inputs are inherently a logic
input with no low frequency filtering. Any
mechanical contacts used for these
inputs in a dual count mode must be
debounced externally. The user input
may only be selected for sink/source by
the user jumper placement.
Prescaler Output
NPN Open Collector: I
SNK
= 100 mA
max @ V
OL
= 1 Vdc max, VOH= 30 Vdc
max with duty cycle of 25% min
and 50% max
Display Indication: Three vertical
dots on the left side of the unit identify
the displays for the following modules
Setpoint Indication: Four vertical
dots on the right side of the unit
identify the setpoint “ON” condition,
with SP 1 being the top position
through SP 4 at the bottom
Programming: The unit is a large
display, designed to be remotely
mounted. Therefore, the unit does
not have a programming keypad.
Unit programming should be
accomplished by one of the
following methods:
Rear Terminal Block: External
switches can be wired via the
terminal block to allow unit
programming. A minimum of
3 switches would be required.
Optional Programming Remote
(LD6-PGM): This option provides a
10' interconnecting cable and
programming box. The programming
remote contains buttons allowing easy
programming of the display.
Optional Serial Programming:
You can purchase an RS232 or
RS485 Comms card and program the
unit via Windows
®
based software
programs. See available Comm cards
shown on ordering page
Environmental Conditions
Operating Temperature Range:
Determined by the input module
Storage Temperature Range:
-40 to 60°C (-40 to 15°F)
Operating and Storage Humidity:
0 to 85% max RH (non-condensing)
Altitude: Up to 2000 m (6562')
Mounting Requirements:
Max panel thickness is 9.5 mm (0.375")
Min panel thickness for NEMA 4 (IP65)
sealing is 1.52 mm (0.060")
Page 2
M-X
Dimensions: mm (in)
629
(24.77)
183
(7.22)
118
(4.65)
91.5
(3.60)
154.7
(6.09)
Connections: Wiring connections are
made to the terminal block and input
module via high compression
cage-clamp terminal blocks
Terminal Block Wiring
Wire Strip Length: 7.5 mm (0.3")
Wire Gage: 30-12 AWG copper wire
Maximum Torque: 5-7 inch-lbs
(0.58-0.81 N-m)
Construction: Aluminum front panel,
enclosure, and rear cover with textured
black polyurethane paint for scratch and
corrosion resistance protection. Sealed
front panel meets NEMA 4X (IP65)
specifications for indoor use when
properly installed. Installation Category
II, Pollution Degree 2. Panel gasket and
keps nuts included.
Weight: 2.25 kg (5 lbs) (less module)
OPTION BOARDS
SPECIFICATIONS
RS485 Communication Card
(LDP6-CDC10 or LDP6-CDC1C)
Type: RS485 multi-point
balanced interface
Isolation to Sensor and User Input
Commons: 500 Vrms for 1 min
Working Voltage: 50V not isolated from
all other commons
Baud Rate: 300 to 19.2k
Data Format: 7/8 bits; odd, even,
or no parity
Bus Address: 0 to 99,
max 32 meters per line
Transmit Delay: Selectable;
2 to 50 msec or 50 to 100 msec
RS232 Communication Card
(LDP6-CDC20 or LDP6-CDC2C)
Type: RS232 half duplex
Isolation to Sensor and User Input
Commons: 500 Vrms for 1 min
Working Voltage: 50V not isolated from
all other commons
Baud Rate: 300 to 19.2k
Data Format: 7/8 bits; odd, even
or no parity
Modbus Communications Card
(LDP6-CDC40 or LDP6-CDC4C)
Type: RS485; RTU and ASCII
MODBUS modes
Isolation to Sensor and User Input
Commons: 500 Vrms for 1 minute
Working Voltage: 50V not isolated from
all other commons
Baud Rates: 300 to 38400
Data: 7/8 bits
Parity: No, Odd, or Even
Addresses: 1 to 247
Transmit Delay: Programmable; See
Transmit Delay explanation.
Analog Output Card (LDP6-CDL)
Types: 0 to 20 mA, 4 to 20 mA and
0 to 10 Vdc
Isolation to Sensor and User Input
Commons: 500 Vrms for 1 min
Working Voltage: 50V not isolated
from all other commons
Accuracy: 0.17% of FS (18 to 28°C);
0.4% of FS (0 to 50°C)
Resolution: 1/3500
Compliance:
10 Vdc: 10 KΩ load min
20 mA: 500 Ω load max
Update Time: 200 msec max to within
99% of final readout value (digital filter
and internal zero correction disabled)
700 msec max (digital filter disabled,
internal zero correction enabled)
LDP63000-AC: 1 sec max to
within 99% of final readout value
(digital filter disabled)
Setpoint Output Cards (Four
Types of Field Installable Cards)
Response Time: 200 msec max
to within 99% of final readout value
(digital filter and internal zero
correction disabled) 700 msec max
(digital filter disabled, internal zero
correction enabled)
LDP63000-AC Only: 1 sec max
to within 99% of final readout value
(digital filter disabled)
LDP63000-T Only: 200 msec typ;
700 msec max (digital filter disabled)
Dual Relay Card (LDP6-CDS10)
Type: Two FORM-C relays
Isolation to Sensor and User Input
Commons: 2000 Vrms for 1 min
Working Voltage: 250V
Contact Rating:
One Relay Energized: 5 Amps
@ 120/240 Vac or 28 Vdc (resistive
load), 1⁄8 HP @120 Vac, inductive load
(total current with both relays
energized not to exceed 5 Amps)
Life Expectancy: 100 K cycles min at
full load rating. External RC snubber
extends relay life for operation with
inductive loads
Quad Relay Card (LDP6-CDS20)
Type: Four FORM-A relays
Isolation to Sensor and User Input
Commons: 2300 Vrms for 1 min
Working Voltage: 250 Vrms
Contact Rating:
One Relay Energized: 3 amps @
250 Vac or 30 Vdc (resistive load),
1
⁄10 HP @120 Vac, inductive load (total
current with all four relays energized
not to exceed 4 Amps)
Life Expectancy: 100 K cycles min at
full load rating. External RC snubber
extends relay life for operation with
inductive loads
Quad Sinking Open Collector
(LDP6-CDS30)
Type: Four isolated sinking NPN
transistors
Isolation to Sensor and User Input
Commons: 500 Vrms for 1 min
Working Voltage: 50V not isolated from
all other commons
Rating: 100 mA max @ V
SAT
= 0.7V max
V
MAX
= 30V
Quad Sourcing Open Collector
(LDP6-CDS40)
Type: Four isolated sourcing PNP
transistors
Isolation to Sensor and User Input
Commons: 500 Vrms for 1 min
Working Voltage: 50V not isolated from
all other commons
Rating:
Internal Supply: 24 Vdc ± 10%,
30 mA max total all four
External Supply: 30 Vdc max,
100 mA max each output
Programming Software
(Free download at omega.com)
Allows configuration of the LDPF63100
meter from a PC. This software offers
standard drop-down menu commands,
that make it easy to program the meter.
The unit program can then be saved in a
PC file for future use. A serial plug-in
card is required to program the meter
using the software.
Page 3
LDPF63100, $696, shown smaller than actual size.
M
M-3
To Order
(Specify Model Number)
Model No. Price Description
LDPF63100 $696 Large display meter, digital inputs, 85 to 250 Vac power
AVAILABLE FOR FAST DELIVERY!
Optional Plug-in Output Cards (Field Installable)
Optional Plug-in Output Cards (Field Installable)
Model No. Price Description
Setpoint Alarms (Only 1 Alarm Card Can Be Installed Into Base Meter)
LDP6-CDS10 $37 Dual setpoint relay output card
LDP6-CDS20 28 Quad setpoint relay output card
LDP6-CDS30 37 Quad setpoint sinking open collector output card
LDP6-CDS40 37 Quad setpoint sourcing open collector output card
Analog Output
LDP6-CDL10 $74 Analog output card
Communications (Only 1 Communications Card Can Be Installed Into Base Meter)
LDP6-CDC10 $48 RS485 Serial communications output card with terminal block
LDP6-CDC1C 48 Extended RS485 Serial communications output card with dual RJ11 connector
LDP6-CDC20 48 RS232 Serial communications output card with terminal block
LDP6-CDC2C 48 Extended RS232 Serial communications output card with 9-Pin D connector
LDP6-CDC40 58 MODBUS communications card
LDP6-CDC4C 58 Extended MODBUS communications card with dual RJ11 connector
Software is free—Download from omega.com
Comes with complete operator’s manual.
Note: Adding option cards—meters can be fitted with up to 3 optional plug-in cards, however, only 1 card from each function type can be
installed at a time. The function types include setpoint alarms, analog output and communications. The cards can be installed initially or at a
later date. Each optional plug-in card is shipped with installation and programming instructions.
Ordering Example: LDPF63100, large display meter for digital input, 85 to 250 Vac power, LDP6-CDL10 analog output card, $696 + 74 = $770.
Model No. Price Description
LDP6-PGM $61 Remote programming module with 3 m (10') cable
LDP6-ENC12 168 NEMA 4 (IP65) enclosure
LDP631-SHR 52 Shroud
LDP6-EN/SH 209 NEMA 4 (IP65) enclosure with shroud
EE-2401 30 Reference Book: Electricians Testing and
Troubleshoooting Pocket Guide
Accessories
Page 4
One Omega Drive | Stamford, CT 06907 | 1-888-TC-OMEGA (1-888-826-6342) | info@omega.com
EPG05
www.omega.com
UNITED KINGDOM
www. omega.co.uk
Manchester, England
0800-488-488
UNITED STATES
www.omega.com
1-800-TC-OMEGA
Stamford, CT.
CANADA
www.omega.ca
Laval(Quebec)
1-800-TC-OMEGA
GERMANY
www.omega.de
Deckenpfronn, Germany
0800-8266342
Karviná, Czech Republic
FRANCE
www.omega.fr
Guyancourt, France
088-466-342
CZECH REPUBLIC
www.omegaeng.cz
596-311-899
BENELUX
www.omega.nl
Amstelveen, NL
0800-099-33-44
More than 100,000 Products Available!
Temperature
Calibrators, Connectors, General Test and Measurement
Instruments, Glass Bulb Thermometers, Handheld Instruments
for Temperature Measurement, Ice Point References,
Indicating Labels, Crayons, Cements and Lacquers, Infrared
Temperature Measurement Instruments, Recorders Relative
Humidity Measurement Instruments, RTD Probes, Elements
and Assemblies, Temperature & Process Meters, Timers and
Counters, Temperature and Process Controllers and Power
Switching Devices, Thermistor Elements, Probes and
Assemblies,Thermocouples Thermowells and Head and Well
Assemblies, Transmitters, Wire
Flow and Level
Air Velocity Indicators, Doppler Flowmeters, Level
Measurement, Magnetic Flowmeters, Mass Flowmeters,
Pitot Tubes, Pumps, Rotameters, Turbine and Paddle Wheel
Flowmeters, Ultrasonic Flowmeters, Valves, Variable Area
Flowmeters, Vortex Shedding Flowmeters
pH and Conductivity
Conductivity Instrumentation, Dissolved Oxygen
Instrumentation, Environmental Instrumentation, pH
Electrodes and Instruments, Water and Soil Analysis
Instrumentation
Data Acquisition
Auto-Dialers and Alarm Monitoring Systems,
Communication Products and Converters, Data
Acquisition and Analysis Software, Data Loggers
Plug-in Cards, Signal Conditioners, USB, RS232, RS485
and Parallel Port Data Acquisition Systems, Wireless
Transmitters and Receivers
Pressure, Strain and Force
Displacement Transducers, Dynamic Measurement
Force Sensors, Instrumentation for Pressure and Strain
Measurements, Load Cells, Pressure Gauges, Pressure
Reference Section, Pressure Switches, Pressure Transducers,
Proximity Transducers, Regulators,
Strain Gages, Torque Transducers, Valves
Heaters
Band Heaters, Cartridge Heaters, Circulation Heaters,
Comfort Heaters, Controllers, Meters and Switching
Devices, Flexible Heaters, General Test and Measurement
Instruments, Heater Hook-up Wire, Heating Cable
Systems, Immersion Heaters, Process Air and Duct,
Heaters, Radiant Heaters, Strip Heaters, Tubular Heaters
click here to go to the omega.com home page
Loading...