Omega Products LDPF63000 User Manual

M-X

M

LARGE DISPLAY METER

FOR DIGITAL INPUT

LDPF63000

$

515

⻬ Large LED Display

Readable to 21 m (70')

⻬ Digital Input Module;

Count and Rate Input
Serial Slave

⻬ Alarms, Analog Output,

and Communication

⻬ Programmable

User Inputs

⻬ Programmable

Function Keys

⻬ PC Software for

Meter Configuration

⻬ NEMA 4 (IP65)

The LDPF63000 display is a
versatile display that can increase
productivity by offering the plant
floor or production area a large
visual display of their current status.
Whether your measurement is rate
or count, the LDPF63000 can
satisfy your requirement. These
LDPF63000 displays accept various
digital inputs through the use of
input modules that allow the unit to
adapt to most any application.
Additional plug-in option cards can
add alarms, analog output, and
communication/bus capabilities,
making the LDPF63000 a truly
intelligent panel meter.

SPECIFICATIONS

Rate Display

Accuracy: ±0.01%
Min Frequency: 0.01 Hz
Max Frequency: 34 kHz

(depending on set-up)

Max Display:

6 Digits: 999999

Adjustable Display (Low) Update:

0.1 to 99.9 seconds

Counter Displays

Maximum Display:
8-Digits: ±99999999 (greater than

6-digits display alternates between
high order and low order)

Inputs A and B

DIP switch selectable to accept pulses
from a variety of sources including
switch contacts, TTL outputs, magnetic
pickups and all standard sensors
Logic: Input trigger levels

V

IL

= 1.5V max;

V

IH

= 3.75V min
Current Sinking: Internal 7.8 kΩ
pull-up to 12 Vdc,

I

MAX

= 1.9 mA
Current Sourcing: Internal 3.9 kΩ
pull-down, 7.3 mA max @ 28 Vdc,

V

MAX

= 30 Vdc

Filter: Damping capacitor provided
for switch contact bounce. Limits input
frequency to 50 Hz and input pulse
widths to 10 msec minimum

Magnetic Pickup

Sensitivity: 200 mV peak
Hysteresis: 100 mV
Input Impedance: 3.9 kΩ @ 60 Hz
Max Input Voltage: ±40V peak, 30 Vrms
Dual Count Modes: When any dual

count mode is used, then user inputs
1 and/or 2 will accept the second signal
of each signal pair. The user inputs do
not have the Logic/Mag, High/Low
Freq, and Sink/Source input setup
switches. The user inputs are
inherently a logic input with no low
frequency filtering. Any mechanical
contacts used for these inputs in a
dual count mode must be debounced
externally. The user input may only be
selected for sink/source by the user
jumper placement.

LDPF63000, $515, shown
smaller than actual size.

M-X

Prescaler Output

NPN Open Collector: I

SNK

= 100 mA

max @

V

OL

= 1 Vdc max VOH= 30 Vdc
max with duty cycle of 25% min and
50% max

Display: 38 mm (1.5") red LED
Power: 85 to 250 Vac, 50/60 Hz, 18 VA
Annunciators: A, B, C, SP1, SP2, SP3,

and SP4
Keypad: Five tactile membrane
switches integrated into the front panel

Enviromental Conditions

Operating Temperature Range:

0 to 45°C (32 to 113°F)

Storage Temperature Range:

-40 to 60°C (-40 to 140°F)

Operating and Storage Humidity:

0 to 85% max RH (non-condensing)

Altitude: Up to 2000 m (1.24 mi)

Mounting Requirements

Max panel thickness is 9.5 mm (0.375")
Min panel thickness for NEMA 4 (IP65)
sealing is 1.57 mm (0.060")
Connections: All wiring connections
are made to the module via high
compression cage-clamp terminal
blocks. Wiring instructions are provided.
Construction: Steel front panel,
enclosure, and rear cover with textured
black polyurethane paint for scratch
and corrosion resistance protection.
Sealed front panel meets NEMA 4
(IP65) specifications for indoor use
when properly installed. Installation
Category II, Pollution Degree II.
Panel gasket and keps nuts included.

Weight: 1.2 kg (2.7 lb) (less module)

OPTION BOARDS
SPECIFICATIONS

RS485 Communication Card:
(LDP6-CDC10 or LDP6-CDC1C)

Type: RS485 multi-point

balanced interface

Isolation to Sensor and User
Input Commons: 500 Vrms for 1 min

Working Voltage: 50V not isolated

from all other commons

Baud Rate: 300 to 19.2k
Data Format: 7/8 bits; odd, even,

or no parity
Bus Address: 0 to 99, max 32 meters

per line
Transmit Delay: Selectable

2 to 50 msec or 50 to 100 msec

RS232 Communication Card
(LDP6-CDC20 or LDP6-CDC2C)

Type: RS232 half duplex
Isolation to Sensor and User

Input Commons: 500 Vrms for 1 min

Working Voltage: 50V not Isolated

from all other commons

Baud Rate: 300 to 19.2k
Data Format: 7/8 bits; odd, even

or no parity

MODBUS®Communications Card
(LDP6-CDC40 or LDP6-CDC4C)

Type: RS485; RTU and ASCII

MODBUS modes

Isolation to Sensor and User Input
Commons: 500 Vrms for 1 minute

Working Voltage: 50V not isolated

from all other commons

Baud Rates: 300 to 38400
Data: 7/8 bits
Parity: No, odd, or even
Addresses: 1 to 247

Analog Output Card (LDP6-CDL)

Types: 0 to 20 mA, 4 to 20 mA and

0 to 10 Vdc

Isolation to Sensor and User Input
Commons: 500 Vrms for 1 min
Working Voltage: 50V not isolated

from all other commons
Accuracy: 0.17% of FS (18 to 28°C);

0.4% of FS (0 to 50°C)

Resolution: 1/3500
Compliance:

10 Vdc: 10 kΩ load min
20 mA: 500 Ω load max

Update Time: 200 msec max to within

99% of final readout value (digital filter
and internal zero correction disabled)
700 msec max (digital filter disabled,
internal zero correction enabled)

LDP63000-AC: 1 sec max to within
99% of final readout value (digital filter
disabled)

Setpoint Output Cards (Four

Types of Field Installable Cards)

Response Time: 200 msec max to within

99% of final readout value (digital filter
and internal zero correction disabled)
700 msec max (digital filter disabled,
internal zero correction enabled)

LDP63000-AC Only: 1s max to within
99% of final readout value (digital filter
disabled)

LDP63000-T Only: 200 msec typ.;
700 msec max (digital filter disabled)

Dual Relay Card (LDP6-CDS10)

Type: Two Form C (SPDT) relays
Isolation to Sensor and User Input

Commons: 2000 Vrms for 1 min
Working Voltage: 250V
Contact Rating:

One Relay Energized: 5 A @

120/240 Vac or 28 Vdc (resistive
load),

1

⁄8 HP @120 Vac, inductive load
total current with both relays
energized not to exceed 5 A

Life Expectancy: 100k cycles min at
full load rating. External RC snubber
extends relay life for operation with
inductive loads.

Quad Relay Card (LDP6-CDS20)

Type: Four Form A (SPST) relays
Isolation to Sensor and User Input

Commons: 2300 Vrms for 1 min
Working Voltage: 250 Vrms
Contact Rating:

One Relay Energized: 3 A @ 250

Vac or 30 Vdc (resistive load),

1

⁄10 HP @120 Vac, inductive load total
current with all four relays energized
not to exceed 4 A

Life Expectancy: 100k cycles min at
full load rating. External RC snubber
extends relay life for operation with
inductive loads.

Quad Sinking Open
Collector (LDP6-CDS30)

Type: Four isolated sinking

NPN transistors

Isolation to Sensor and User
Input Commons: 500 Vrms for 1 min
Working Voltage: 50V not isolated

from all other commons
Rating: 100 mA max @ Vsat = 0.7V
max Vmax = 30V

Quad Sourcing Open
Collector (LDP6-CDS40)

Type: Four isolated sourcing

PNP transistors

Isolation to Sensor and User
Input Commons: 500 Vrms for 1 min

Working Voltage: 50V not isolated

from all other commons

Rating:

Internal Supply: 24 Vdc ± 10%,

30 mA max total all four
External Supply: 30 Vdc max,
100 mA max each output

Programming Software

(Free download at omega.com/dp6soft)
Allows configuration of the LDPF63000
meter from a PC. This software offers
standard drop-down menu commands,
that make it easy to program the meter.
The unit program can then be saved in
a PC file for future use. A serial plug-in
card is required to program the meter
using the software.