Omega Products LDP63200-4 User Manual

Large Display Process Meter



LDP63200 Series

Starts at

520

⻬ 57 mm (2.25") and

101 mm (4") High Red LED Digits

⻬ Programmable Scaling

and Decimal Points

⻬ Programmable User Input ⻬ Dual 5 Amp

Form C Relay

⻬ Aluminum NEMA 4X

(IP65) Case Construction

⻬ RS232/RS485 Serial

Communications

⻬ Universally Powered

The LDP63200 Series are versatile large display meters available as a DC volt, current, or process meter with scaling, serial communications and dual relay outputs. The 5-digit displays are available in either 57 mm (2.25") or 101 mm (4") high red LED digits with adjustable display intensities. The 57 mm (2.25") high models are readable up to 39.6 m (130'). The 101 mm (4") high models are readable up to

54.9 m (180'). Both versions are constructed of a NEMA 4X (IP65) enclosure in light weight aluminum. All models also come with dual Form C relay outputs and RS232/ RS485 serial communications.

Specifications

Display: 5-digit, 57 mm (2.25") or

101 mm (4") intensity adjustable red LED (-99999 to 99999)

Power Requirements

AC Power: 50 to 250 Vac 50/60 Hz,

26 VA

DC Power: 21.6 to 250 Vdc, 11 W DC Out: ±24 Vdc at 100 mA if input

voltage is greater than 50 Vac/Vdc ±24 Vdc at 50 mA if input voltage is less than 50 Vdc

Isolation: 2300 Vrms for 1 min to all inputs and outputs

Input Ranges: Jumper selectable

4" High

LEDS

LDP63200-2, $520.

A/D Converter: 16 bit resolution A/D Conversion Rate: 6 readings/sec Display Response Time: 500 msec min

User Input

Software: Selectable pull-up (8.6 K) or

pull-down resistor (3.9 K) that determines active high or active low input logic.

Trigger levels: VIL= 1.0V max; VIH=

2.4V min; V Response Time: 5 msec typ; 50 msec

debounce (activation and release)

Communications

Type: RS485 or RS232 Isolation To Sensor and User Input

Commons: 500 Vrms for 1 min Working Voltage: 50V not isolated from

all other commons

Data: 7/8 bits Parity: No, odd or even Baud Rate: 300 to 38.4 K Bus Address: Selectable 0 to 99,

max 32 m (105') per line (RS485) Memory: Nonvolatile EEPROM retains

all programming parameters and max/min values when power is removed

Output

Type: Single FORM-C relay Isolation to Sensor and User Input

Commons: 1400 Vrms for 1 min Working Voltage: 150 Vrms Contact Rating:

Resistive Load:

5 amps @ 120/240 Vac or 28 Vdc

Inductive Load:

Life Expectancy: 100,000 min operations

MAX

= 28 Vdc

⁄8 H.P. @ 120 Vac

M-1

LDP63200-4, $718.

2.25" High LEDS

Both shown smaller

than actual size.

Response Time

Turn On: 4 msec max Turn Off: 4 msec max

Environmental Conditions

Operating Temperature: 0 to 65°C

(32 to 149ºF) Storage Temperature: -40 to 70°C

(-40 to 158ºF)

Operating and Storage Humidity:

0 to 85% max RH (non-condensing)

Vibration According to IEC 68-2-6:

Operational 5 to 150 Hz, in X, Y, Z direction for 1.5 hours, 2 g’s (1 g relay)

Shock According to IEC 68-2-27:

Operational 30 g’s (10 g relay), 11 msec in 3 directions

Altitude: Up to 2000 m (6561') Connections: Internal removable

terminal blocks

Wire Strip Length: 10 mm (0.4") Wire Gage: 24-12 AWG copper wire,

90°C rated insulation only

Torque: 5.3 inch-lbs (0.6 N-m) max Cable Diameter: Outside diameter must

be 4.6 mm (0.181") to 7.9 mm (0.312") to maintain NEMA 4 (IP65) rating of cord grips

Construction: Aluminum enclosure, steel side panels with textured black polyurethane paint for scratch and corrosion resistance protection. Meets NEMA 4X (IP65) specifications. Installation Category II, pollution degree 2

Weight:

LDP63200-2: 2.04 kg (4.5 lb) LDP63200-4: 4.76 kg (10.5 lb)



Extended Warranty

Program



Air Pressure Stabilization Vent

Dimensions: mm (in)

Model No. X (Length) Y (Height) Z (Center) LDP63200-2 406.4 (16) 101.6 (4) 304.3 (12)

LDP63200-4 660.4 (26) 200 (7.875) 558.8 (22)

D.C. Voltages: 200 mV, 2V, 20V, 200V, 10V

Input Accuracy at 23°C Input Temperature

Range Less than 85% RH Impedance Resolution Coefficient

200 mV 0.1% of span 1.027 MΩ 10 µv 70 ppm/°C

2V 0.1% of span 1.027 MΩ 0.1 mV 70 ppm/°C

20V 0.1% of span 1.027 MΩ 1 mV 70 ppm/°C

200V 0.1% of span 1.027 MΩ 10 mV 70 ppm/°C

10V 0.1% of span 1.027 MΩ 1 mV 70 ppm/°C

D.C. Currents: 200 µA, 2 mA, 20 mA, 200 mA

Input Accuracy at 23°C Input Max Temperature

Range Less than 85% RH Impedance Input Signal Resolution Coefficient

200 µA 0.1% of span 1.111 kΩ 15 mA 10 nA 70 ppm/°C

2 mA 0.1% of span 111 Ω 15 mA 0.1 µA 70 ppm/°C

20 mA 0.1% of span 11 Ω 15 mA 1 µA 70 ppm/°C

200 mA 0.1% of span 1 Ω 15 mA 10 µA 70 ppm/°C

57.15 (2.25)

Comes complete with operator’s manual.

Accessory (Field Installable)

Ordering Example: LDP63200-4, large 102 mm (4") display process meter, $718. OCW-3, OMEGACARE to a total of 5 years ($179), $718 + 179 = $897.

D.C. Process: 4 to 20 mA, 1 to 5 Vdc, 0/1 to 10 Vdc

OMEGACARESMextended warranty program is available for models shown on this page. Ask your sales representative for full details when placing an order. OMEGACARE covers parts, labor and equivalent loaners.

Input Range Select Range

4 to 20 mA Use the 20 mA range

1 to 5 Vdc Use the 10V range

1 to 10 Vdc Use the 10V range

AVAILABLE FOR FAST DELIVERY!

To Order (Specify Model Number)

Model No. Price Description (Display Meter Only, No Outputs) LDP63200-2 $520 Large 57 mm (2.25") display process meter LDP63200-4 718 Large 102 mm (4") display process meter

Model No. Price Description LDP63200-PLUG $5 Plug to seal unused wiring connection ports (for NEMA 4 rating only)

extends standard 2-year warranty

M-2

+ 1 hidden pages