HIGH-ACCURACY STAINLESS STEEL
CANTILEVER BEAMS
STANDARD AND METRIC MODELS
LC501/LCM501 Series
LC511/LCM511 Series
Tension/Compression
0-100 lb to 0-100,000 lb-
Standard Models
0-25 kgf to 0-10,000 kgfMetric Models
STANDARD
LC501-20K, $695, shown
smaller than actual size.
METRIC
LCM501-10K, $695 shown
smaller than actual size.
Starts at
$
340
Standard
⻬ FM Approved
Intrinsically Safe Rating
⻬ All Stainless Steel
Construction for Harsh
Industrial Applications
⻬ 0.25% Interchangeability
for Multiple Cell
Applications
⻬ 5-Point Calibration
Provided
IP65
Protection
Level
TWA5-750 self adjusting weigh
module, $560, shown smaller than
actual size. See page F-76.
F-73
A
GF
W
D1
D1
D
D
4.6 m (15') 4-CONDUCTOR
PVC INSULATED CABLE
1/2-14 NPT FITTING
E
22 (0.88)
B
C
30°
32
(1.25)
42
(1.67)
57
(2.25)
44 (1.75)
Wiring Code
Wire—Pin Connector
GREEN (A) + Output
WHITE (B) – Output
BLACK (C and E) – Input
RED (D and F) + Input
SPECIFICATIONS
A
GF
B
E
4.6 m (15')
4-CONDUCTOR PVC
CABLE
LC501/LC511: 10-32
TAPPED HOLE FOR
LOCKING SCREW
J
D1
D1
I
C
D
D
LCM501/LCM511: M5 x 0.8
Excitation: 10 Vdc, 15 Vdc max
Output: 3 mV/V ±0.25%
5-Point Calibrated (in Compression):
0%, 50%, 100%, 50%, 0%
Linearity: ±0.03% FSO
Hysteresis: ±0.02% FSO
Repeatability: ±0.02% FSO
Zero Balance: ±1% FSO
Agency Approvals: FM Intrinsically
Safe IS/I.II.III/1/CDEFG
Operating Temp Range:
-34 to 82°C (-30 to 180°F)
Compensated Temp Range:
16 to 71°C (60 to 160°F)
Thermal Effects:
Zero: ±0.001% FSO/ºF (0.0018%/°C)
Span: ±0.001% FSO/ºF (0.0018%/°C)
Safe Overload: 150% of capacity
Ultimate Overload: 300% of capacity
Input Resistance: 360 Ω minimum
Output Resistance: 350 ±10 Ω
FS Deflection: 0.5 mm (0.02") typical
Construction: 17-4 PH stainless steel,
>20,000 lb, high-alloy steel
Electrical:
LC501/LCM501: 4.6 m (15')
4 conductor shielded cable
LC511/LCM511: 6-pin DT02H-10-6P
or equivalent
Mating Connector: PT06F10-6S
$26.50 (sold separately)
Ranges ≤20,000 lb/10,000 kgf
Ranges >20,000 lb
Dimensions:
mm (in)
Wire PIN Connection
GN A +Output
WT B -Output
BK C&E -Input
RD D&F +Input
Dimensions: mm (in)
CAPACITY ABCDD1 EFGIJ
100 to 121 19 25 9.9 15 25 13 25 3⁄8-18 UNC1⁄2-20 0.9
750 lb (4.75) (0.75) (1.0) (0.39) (0.59) (1.0) (0.50) (1.0) (2)
1K to 5K lb 173 25 38 13 20 38 13 381⁄2-14 UNC1⁄2-20 1.8
10K lb 197 25 38 20 n/a 38 19 51 1⁄2-14 UNC3⁄4-16 2.3
20K lb 241 25 64 20 n/a 51 25 571⁄2-14 UNC 1-12 5
50K to 330 51 102 26 40 90 32 701⁄2-14 UNC n/a 19
100K lb (13.00) (2.0) (4.0) (1.03) (1.56) (3.5) (1.25) (2.75) (42)
25 to 121 19 25 9.9 15 25 13 25 3⁄8-18 UNC M12 x 1.75 0.9
250 kgf (4.75) (0.75) (1.0) (0.39) (0.59) (1.0) (0.50) (1.0) (2)
500 to 173 25 38 13 20 38 13 381⁄2-14 UNC M12 x 1.75 1.8
2500 kgf (6.75) (1.0) (1.5) (0.53) (0.77) (1.5) (0.50) (1.5) (4)
5000 kgf 197 25 38 20 n/a 38 19 51 1⁄2-14 UNC M20 x 1.5 2.3
10,000 kgf 241 25 64 20 n/a 51 25 571⁄2-14 UNC M24 x 2.0 5
Accessory Hardware:
TWA/TWAM Series (Page F-76)
Self-Adjusting Weigh Modules
Nickel-Plated Carbon Streel or
(6.75) (1.0) (1.5) (0.53) (0.77) (1.5) (0.50) (1.5) (4)
(7.75) (1.0) (1.5) (0.77) (1.5) (0.75) (2.0) (5)
(9.50) (1.0) (2.5) (0.77) (2.0) (1.00) (2.25) (11)
(7.75) (1.0) (1.5) (0.77) (1.5) (0.75) (2.0) (5)
(9.50) (1.0) (2.5) (0.77) (2.0) (1.00) (2.25) (11)
Stainless Steel
WEIGHT
kg (lb)
STANDARD
LOAD CELLS
F-74
METRIC