Omega Products IP210-X120 User Manual

CURRENT TO PRESSURE (I/P) CONVERTER
IP210 Series
Control Air 3-15 to 3-120 psi
$
535
All Models
Loop PoweredIdeal for Pneumatic
Control Systems
IP65 Sealed CaseZero and Span
Rugged Zinc-Cast
Housing
A “current to pressure” converter (I/P) converts an analog signal (4 to 20 mA) to a proportional linear pneumatic output (3 to 15 psig). Its purpose is to translate the analog output from a control system into a precise, repeatable pressure value to control pneumatic actuators/operators, pneumatic valves, dampers, vanes, etc. The IP210 is a loop-powered instrument, which eliminates the need for an external power supply (except for IP210-X120).
Principle of Operation
OMEGA’s IP210 converts an analog signal (4 to 20 mA) to a proportional linear pneumatic output (3 to 15 psig). Its uncomplicated design and proven electromagnetic force balance deliver consistently high performance.
IP210-X15, $535,
shown actual size.
The IP210 provides a reliable, repeatable, accurate means of converting an electrical signal into pneumatic pressure. Its force balance principle is a coil suspended in a magnetic field on a flexible mount. At the lower end of the coil is a flapper valve that operates against a precision ground nozzle to create a backpressure on the servo diaphragm of a booster relay.
The input current flows in the coil and produces a force between the coil and the flapper valve, which controls the servo pressure and the output pressure.
Zero adjustment of the unit is made by turning a screw that regulates the distance between the flapper valve and the air nozzle. Span adjustment
See Section Y for a
Selection of Scientific,
Technical, and Reference
Books Available from
omega.com
is made by varying a potentiometer, which shunts input current past the coil. An integral volume flow booster provides adequate flow capacity, resulting in fast response time and accurate control.
L-9
LOOP-POWERED ELECTROPNEUMATIC CONTROL
FRONT VIEW
REMOVABLE ORIFICE
SUPPLY IN
OUTPUT
2 HOLES 06.5 mm
PLUG ORIENTS 4 WAYS
RANGE OR SPAN
(TYPICAL)
8
(0.31)
=
=
=
=
=
=
RANGE ZERO
54
(2.1)
73 (2.9)
54 (2.1)
61.5 (2.4)
120
(4.7)
51 (2)
67 (2.6)
OUTLET PRESSURE (bar)
FLOW (N/MIN)
RELIEF FLOW CHARACTERISTICS
(SUPPLY PRESSURE 7 bar)
FORWARD FLOW CHARACTERISTICS
(SUPPLY PRESSURE 7 bar)
FLOW (N/MIN)
OUTLET PRESSURE (bar)
5
4
3
2
1
0
0 100 200 300 400 500 600
8
6
4
2
0
-700 -600 -500 -400 -300 -200 -100 0
OUTLET PRESSURE
MAX
MIN
MIN
MAX
INPUT SIGNAL
SPAN/ZERO ADJUSTMENTS
R
20% OF OUTPUT RANGE
100 200 300 400 500 600
8
-300 -200 -100 0
Dimensions: mm (in)
SPECIFICATIONS
Accuracy: 0.5% FS Supply Sensitivity: 0.025% span
per % supply pressure change
Zero Adjustment: 5% FS Span Adjustment: 20% FS Operating Temp:
-20 to 70°C (-5 to 160°F)
Compensated Temp:
-10 to 60°C (15 to 140°F)
Thermal Effects:
<0.1%/°C over operating range Input Resistance: <300 Ω
To Order (Specify Model Number)
MODEL NO. PRICE INPUT RANGE OUTPUT RANGE
IP210-X15 $535 4 to 20 mA 3 to 15 psig IP210-X30 535 4 to 20 mA 3 to 30 psig IP210-X60 535 4 to 20 mA 3 to 60 psig IP210-X120 535 4 to 20 mA* 3 to 120 psig
3-wire system. External 24 Vdc power supply required.
*
Comes complete with operator’s manual.
Ordering Examples: IP210-X15, I/P converter, takes a 4 to 20 mA control signal and converts it into 3 to 15 psig control air, $535. IP210-X60, I/P converter, takes a 4 to 20 mA control signal and converts it into 3 to 60 psig control air, $535.
Recommended Reference Book: Valve Handbook, GE-2317, $135. Visit omega.com/bobi for Additional Books
Media: Oil-free, clean, dry air filtered
to 25 µm
Recommended Supply Pressure:
25 to 30 psig (filtered air) Max Supply Pressure: 80 psig
(for IP210-X120: 135 psi) Min Supply Pressure: 10 psi above
maximum output pressure
Air Consumption (Leakage): 0.03 scfm Flow Rate: 10
scfm
60 psi;
0.06 >60 psi Response Time: <30 psi
[less than 0.5 s (10 to 90% step);
Failure Mode: Upon electrical failure, the signal pressure falls to bleed pressure
Pressure Port:
1
4 FNPT
Electrical Connection: DIN 43650 with screw terminals included
Housing: IP65 rated, epoxy-painted zinc die castings
Construction: Nitrile diaphragms, stainless steel/nylon flapper, nozzle and supply valve, integral surface mounting bracket included
Weight: 1.7 kg (3 lb)
VALVES AND REGULATORS
30 psi: 2 s]
MOST POPULAR MODELS HIGHLIGHTED!
L
L-10
Loading...
+ 1 hidden pages