Omega Products HX93AV-D User Manual

RH/Temp Humidity Transmitters
Wall, Duct Mount, and Remote Probe Models With Optional Dual Built-In Displays
HX93AC
(without displays)
Optional
U 4 to 20 mA or
0 to 1 Vdc Output for Both RH and Temperature
U Splashproof Enclosure U Accurate to 2.5% RH
and 0.6°C
U New Models with
Built-In Display to Indicate Humidity and Temperature
U Duct Mount Kit Included
with Duct Mount and Remote Probe Models
Relative Humidity Control System
The HX93A and HX93DA Series interface directly with OMEGA’s iSeries meters and controllers to create a complete relative humidity control system. iSeries meters and controllers feature totally programmable color displays and embedded internet connectivity. Visit omega.com
HX93AC wall
mount.
The HX93DA and HX93A Series transmitters provide remote and on-site monitoring of relative humidity and temperature. Both series output a linearized current or voltage signal proportional to the measured humidity or temperature. RH outputs are temperature compensated. Current output models enable placing of the transmitter at a remote location virtually any distance away from the measuring device. The HX93DA models feature built-in dual displays that indicate both humidity and temperature simultaneously. All use a thin-film polymer capacitor to sense relative humidity and a Platinum 100 Ω RTD to sense temperature. A stainless steel mesh type filter, easily removable for cleaning, protects the sensors. Mounting screws are easily accessible inside the rugged, polycarbonate enclosure which houses and protects the electronics to NEMA 13 specifications.
Refer to ordering chart on next page for
NIST calibration ordering information.
U Rugged Industrial
Splashproof Design
U “Humidity Only” Models
Also Available, see page Hu-17 for HX92A Series
Hu-19
1
32 DIN temperature/process
DPi32
meter, shown actual size.
HX93AC-D duct mount, shown smaller than actual size.
HX93A(*)-RPI remote probe humidity transmitter, shown smaller than actual size, supplied with a 1 m (3') cable attached to a 124.5 mm (4.9") stainless steel probe.
HX93DAC,
shown smaller
than actual size.
Displays
Humidity and
Temperature
Simultaneously!
Specifications
Input Voltage Range: 24 Vdc nominal
HX93A Series: 6 to 30 Vdc HX93DA Series: 12 to 30 Vdc
Measuring Range
RH: 3 to 95% Temperature: -20 to 75°C (-4 to 167°F)
Accuracy
RH: ±2.5% RH from 20 to 80%RH;
±3.1% RH below 20 and above 80% RH@ 25°C (76°F) with temp coefficient of ±0.1% RH/°F
Temperature: 0.6°C (±1°F)
Output
HX93AC or HX93DAC:
4 to 20 mA for 0 to 100% RH and -20 to 75°C (-4 to 167°F)
HX93AV: 0 to 1 Vdc for 0 to 100% RH and -20 to 75°C (-4 to 167°F)
RH Temperature Compensation:
-20 to 75°C (-4 to 167°F)
RH Time Constant (90% Response at 25°C, in Moving Air @ 1m/s): >10 seconds: 10 to 90% RH; >15 seconds: 90 to 10% RH
Repeatability: ±1% RH, 0.5°F Housing: Gray polycarbonate,
(IP65, DIN 40050) NEMA rated up to 13, UL listed
Connections: Liquid-tight nylon with neoprene gland, for 0.09 to 0.265" diameter cable; internal 4-pin terminal block accepts 14 to 22 gauge wire
Dimensions: HX93A(*) and HX93A(*)-D Enclosure:
79.8 x 81.8 x 54.9 mm (3.14 x 3.22 x 2.16")
HX93A(*)-D Probe: 15.7 D x 124.5 mm L
(0.620 x 4.9") Weight:
HX93A(*): 170 g (6 oz) HX93A(*)-D: 187 g (6.6 oz)
Displays (HX93DA Series Only)
Dual Miniature Loop-Powered Indicators: 3
Reading Rate: 2.5 times per second Display Accuracy:
Relative Humidity: ±2.5% RH Temperature: ±0.6°C (1°F)
Display Resolution: Relative Humidity: 0.1% RH Temperature: 0.1°C (0.1°F)
Display Accuracy in Relation to Output:
Relative Humidity: ±0.3% RH Temperature: ±0.3°C (0.5°F)
1
2 digit LCD
To Order Visit omega.com/hx93a for Pricing and Details
Model No. Description
HX93A(*) Wall mount RH and temperature transmitter HX93A(*)-D Duct mount RH and temperature transmitter HX93A(*)-RP1 Remote probe relative humidity/temp transmitter HX93DAC-(**) Wall mount, dual display RH/temperature transmitter/indicator HX93DAC-D-(**) Duct mount, dual display RH/temperature transmitter/indicator HX93DAC-RP1-(**) Remote probe, dual display RH/temperature transmitter/indicator HX92-CAL Calibration kit, 11 and 75% RH standards PSR-24S
PSR-24L PSR-24L-230
PSU-93 Unregulated power supply, 16 to 23 Vdc, 300 mA max, screw terminal TX4-100 4-conductor shielded transmitter cable 30 m (100') CAL-3-HU† NIST-traceable calibration HX90DM-KIT
For 4 to 20 mA output, specify “C” or for 0 to 1 Vdc output specify “V”.
*
For temperature display in °C insert “C” or for temperature display in °F insert “F”.
**
Ordering Example: HX93DAC-F, wall mount, dual display RH/temp transmitter indicator with °F display with 4 to 20 mA output, with HX92-CAL calibration kit.
Regulated power supply, US plug, 90 to 264 Vac input, 24 Vdc output, 400 mA, screw terminals, UL Regulated power supply, US plug, 90 to 264 Vac input, 24 Vdc output, 400 mA, stripped leads, UL Regulated power supply, European plug, 230 Vac input, 24 Vdc output, 400 mA, stripped leads, CE
Spare duct mount kit [for HX93DAC-(**)-D, HX93DAC-(**)-RP1, HX93A(*)-D & HX93A(*)-RP1 models only]
H
u
Hu-20
Loading...