Omega Products HPP-600 Installation Manual

HPP-600

Pneumatic Hand Pump

INSTRUCTION

SHEET

M4673/0508

Shop online at: omega.com e-mail: [e-mail]
For latest product manuals: omegamanual.info

Volume Control

The HPP-600 pump is equipped with two knobs for fine adjustment of the system
pressure

. The vent knob can be used to slowly reduce the system pressure. The
vent knob should be closed prior to pressurizing the system by turning the knob
awa

y from the pump housing. The Vernier knob can be used to increase or

decrea

se the system at a more controlled rate. For fast relieve of the pressure,

move the pressure/vacuum pin to the opposite direction.

Pressure/Vacuum Selector

The pump can be used to generate pressure or vacuum depending on the position
of the pin located in the pressure/vacuum switch. Press the pin on the side of the
pump housing according to labels for the desired operation.

For High Pressure Operation

Prior to pressurizing, back out the Vernier knob until the ring on the Vernier shaft
is showing. Pump to pressurize. Turn the Vernier knob towards the pump
housing and the pressure should easily be able to reach 600 psi.

NOTE:

The pump uses a Schrader valve instead of a needle valve. Thus, full open or
closed is several turns from the end of the travel. Over-tightening does not
increase the seal.

Fittings

The pump is equipped with 1/8" and 1/4" BSP ports. In order to use NPT fittings, a
NPT to BSP Parallel Thread Adapter is required. These adapters, which are
included with the pump, have a bonded washer attached to the male end of the
adapter.

MAINTENANCE

No routine maintenance is required. A periodic check of system calibration is
recommended
Omeg
ma
an

a Engineering if repair is needed (field repair should not be attempted and

y void warranty). Be sure to include a brief description of the problem plus

y relevant application notes. Contact customer service to receive a return

. The Pump is not field serviceable and should be returned to

goods authorization number before shipping.

OMEGAnet®On-Line Service Internet e-mail

omega.com [e-mail]

U.S.A.: One Omega Drive, Box 4047

ISO 9001 Certifie

Canada:

U.S.A. and Canada:

Mexico:

Czech Republic:

Germany/Austria: Daimlerstrasse 26, D-75392 Deckenpfronn, Germany

United Kingdom: One Omega Drive, River Bend Technology Centre

ISO 9001 Certified

It is the policy of OMEGA Engineering, Inc. to comply with all worldwide safety and EMC/EMI
regulations that apply. OMEGA is constantly pursuing certification of its products to the European Ne
Approach Directives. OMEGA will add the CE mark to every appropriate device upon certification.

The information contained in this document is believed to be correct, but OMEGA Engineering,
Inc. accepts no liability for any errors it contains, and reserves the right to alter specifications
without notice. WARNING: These products are not designed for use in, and should not be used
for, human applications.

d Stamford, CT 06907-0047

Tel: [phone]

X: [phone]

FA
e-mail: [e-mail]

976 Bergar
Laval (Quebec) H7L 5A1, Canad
Tel: [phone]

X: [phone]

FA
e-mail: info@omega.c

For immediate technical or application assistance:

Sales Service: 1-800-826-6342/1-800-TC-OMEGA
Customer Service: 1-800-622-2378/1-800-622-BEST
Engineering Service: 1-800-872-9436/1-800-USA-WHEN
En Espan˜ol: [phone]-7803
FAX: [phone]
e-mail: [e-mail]
[e-mail]

Frystatska 184, 733 01 Karvina´, Czech Republic
Tel: [phone]

X: [phone]

FA
Toll Free: 0800-1-66342
e-mail: [e-mail]

Tel: [phone]
FA

X: [phone]
Toll Free in Germany:
e-mail: [e-mail]

Northbank, Irlam, Manchester
M44 5BD United Kingdom
Tel: [phone]
FA

X: [phone]
Toll Free in United Kingdom: 0800-488-488
e-mail: [e-mail]

Servicing North America:

a

a

Servicing Europe:

0800 639 7678

®

®

®

OMEGA ENGINEERING, INC. warrants this unit to be free of defects in materials and workmanship for a period of 13 months from

WARRANTY/ DISCLAIMER

date of pu rchase. OMEGA’s
warranty to cover handling and shipping time. This ensures that OMEGA’s customers receive maximum coverage on each product.

If the unit malfunctions, it must be returned to the factory for e valuation. OMEGA’s
Authorized Return (AR) number immediately upon phone or written request. Upon examination by OMEGA, if the unit is found to be
defective, it will be repaired or replaced at no charge. OMEGA’s
purchaser, in cluding but not limited to mishandling, improper interf acing, operation outside of design limits, improper repair,
unauthorized modification. This WARRANTY is VOID if the unit shows evidence of having been tampered with or shows evidence of
hav ing been damag ed a s a r esult of exces siv e
misapplication; misuse or other operating conditions outside of OMEGA’s control. Compo nents in which wear is not warrante d,
include but are not limited to contact points, fuses, and triacs.

OMEGA is pleased to off er suggestio ns on t he use of its vari ous products . Ho wever, OMEGA neither assumes
respons ibility for any omissi ons or er rors nor assume s liab ility for any damages that r esult from the use of it
products in accordance with information provided by OMEGA, either verbal or written. OMEGA warrants only that th
parts manufactured by the company will be as specified and free of defects. OMEGA MAKES NO OTHER WARRANTIE
OR REPRESENTATIONS O F ANY KIND WHATSOEVER, EXPRESSED OR IMPLIED, EXCEPT T HAT
IMPLIE D WARRANTIES INCLUDIN G ANY W ARRAN TY OF M ERCHA NTABILIT Y AND F ITNES S FOR A PARTIC ULAR
PURPOSE
excl usiv e,
negligence, indemnification, strict liability or otherwise, shall not exceed the purchase price of the component upon
which liability is based. In no event shall OMEGA be liable for consequential, incidental or special damages.

CONDITIONS: Equipment sold by OMEGA is not intended to be used, nor shall it be used: (1) as a “Basic Component” under 10 CF
21 (NRC), used in or with any nuclear installation or activity; or (2) in medical applications or used on humans. Should any Product(s
be used in or with any nuclear installation or activity, medical application, used on humans, or misused in any way,
no responsibility as set forth in our basic WARRANTY/ DISCLAIMER language, and, additionally, purchaser will indemnify OMEGA
and hold OMEGA harmless from any liability or damage whatsoever arising out of the use of the Product(s) in such a manner.

Direct all warra nty and repai r requests/in quiri es to the OMEGA Custom er Service Departmen t. BEFORE RETURNING ANY

PRODUCT( S) TO OMEG A, PURCHASER MUST OB TAIN AN
SERVICE DEPART
outside of the return package and on any correspondence.
The purchaser is responsible for shipping charges, freight, insurance and proper packaging to prevent breakage in transit.

FOR WARRANTY RETURNS, please have the following
information available BEFORE contacting OMEGA

1. Purchase Order number under which the product wa

2. Model and serial number of the product under

3. Repair instructions and/or specific problems relative to the

w

OMEGA’s policy is to make running changes, not model changes, whenever an improvement is possible. This affords our customers the lat­est in technology and engineering.

OMEGA is a registered trademark of OMEGA ENGINEERING, INC
© Copyright 2008 OMEGA ENGINEERING, INC. All rights reserved. This document may not be copied, photocopied, reproduced, translated, or

reduced to any electronic medium or machine-readable form, in whole or in part, without the prior written consent of OMEGA ENGINEERING, INC.

ARE HEREBY DISCLA IMED. LIMITATION OF LIABILITY: The remedies of pur chaser set forth herei n are

and the total liabili ty of OME GA with respect to th is order, whether bas ed on con tra ct, warra nty,

PURCHASED

product.

,

WARRANTY adds an addi tional one (1) mon th grace period to the norm al one (1) year produ ct

Customer Service Department wi ll issue an

WARRANTY does not apply to defects resulting from any action of the

cor ros ion ; or cur rent, heat , moist ure or vibr ation; imp rop er s pecifi cation ;

OF TITLE, AND ALL

OMEGA assumes

RETURN REQUESTS / INQUIRIES

MENT (IN ORDER TO AVOID PROCESSING DELAYS). The assi gned AR numbe r should then be marked on the

:

warranty, and

AUTHORIZ ED RETURN (AR) NUMBER FROM OME GA’S C USTOMER

FOR NON-WARRANTY REPAIRS,
charges. Have the following information available BEFORE
contacting OMEGA

s

1. Purchase Order number to cover the COST of the repair,

2. Model and

3. Repair instructions and/or specific problems relative to the
product.

.

:

serial number of the product, and

consult OMEGA for current repair

or

s
e

S

R

)