Omega Products HH505 Installation Manual

OMEGA

HH505

Digital Thermometer

omega. com

OMEGAnetSM On-Line Service

http://www.omega.com

USA: ISO 9001 Certified Canada:

One Omega Drive, Box 4047 976 Bergar

Stamford, CT 06907-0047 Laval (Quebec) H7L5A1

Tel: [phone] Tel: [phone]

FAX: [phone] FAX: [phone]

e-mail: [e-mail] e-mail: [e-mail]

USA and Canada: Mexico and Latin America:

Sales Service: 1-800-826-6342 / 1-800-TC-OMEGA

Customer Service: 1-800-622-2378 / 1-800-622-BEST

Engineering Service: 1-800-872-9436 / 1-800-USA-WHENSMEn Español: [phone]

TELEX: 996404 EASYLINK: 62968934 CABLE: OMEGA e-mail: [e-mail]

Benelux: Germany/Austria:

Postbus 8034, 1180 LA Amstelveen, Daimlerstrasse 26, D-75392

The Netherlands Deckenpfronn, Germany

Tel: [phone] FAX: [phone] Tel: [phone] FAX: [phone]

Toll Free in Benelux: 06 0993344 Toll Free in Germany: 0800 82 66342

e-mail: [e-mail] e-mail: [e-mail]

Czech Republic: United Kingdom: ISO 9002 Certified

ul. Rude armady 1868, 733 01 Karvina- One Omega Drive

Hranice, Czech Repubic Riverbend Technology Centre Northbank, Irlam,

Tel: [phone] FAX: [phone] Manchester, M44 5EX, England

e-mail: [e-mail] Tel: [phone] FAX: [phone]

France:

9, rue Denis Papin, 78190 Trappes Toll Free in England: 0800-488-488

Tel: [phone] FAX: [phone] e-mail: [e-mail]

Toll Free in France: 0800-4-06342

e-mail: [e-mail]

It is the policy of OMEGA to comply with all worldwide safety and EMC/EMI regulations that apply. OMEGA is constantly pursuing certification
of its products to the European New Approach Directives. OMEGA will add the CE mark to every appropriate device upon certification.
The information contained in this document is believed to be correct but OMEGA Engineering, Inc. accepts no liability for any errors it contains,
and reserves the right to alter specifications without notice.
WARNING: These products are not designed for use in, and should not be used for, patient connected application.

For immediate technical or application assistance:

Servicing North America:

SM

SM

Servicing Europe:

TM

Internet e-mail

[e-mail]

Tel: (95) 800-TC-OMEGA

FAX: [phone]

SM

INTRODUCTION

This instrument is a 4½ digit, compact-sized portable digital thermometer
designed to use external 100W Platinum RTD as temperature sensor. Tem­perature indication follows Reference Temperature/Resistance Tables (Pt385
for European Curve, Alpha=.00385 and Pt3926 for American Curve, Al­pha=.003926).

SAFETY INFORMATION

It is recommended that you read the safety and operation instructions before
using the thermometer.

WARNING

To avoid electrical shock, do not use this instrument when working

voltages at the measurement surface over 24V AC or DC.

WARNING

To avoid damage or burns, do not make temperature

measurement in microwave ovens.

The symbol on the instrument indicates that the operator must refer to an
explanation in this manual.

1

SPECIFICATIONS

ELECTRICAL

Temperature Scale: Celsius or Fahrenheit user-selectable.
Measurement Range:

Pt385(100W) -200°C to 800°C, (-328°F to 1472°F)
Pt3926(100W ) -200°C to 630°C, (-328°F to 1166°F)

Resolution: 0.1°C or 0.2°F
Accuracy: Accuracy is specified for operating temperatures over the range of

18°C to 28°C (64°F to 82°F), for 1 year, not including RTD probe error.

±(0.05% rdg + 0.2°C) on °C scale
±(0.05% rdg + 0.4°F) on °F scale

Temperature Coefficient: 0.1 times the applicable accuracy specification

per °C from 0°C to 18°C and 28°C to 50°C (32°F to 64°F and 82°F to 122°F).
Input Protection: 24V dc or 24V ac rms maximum input voltage on any

combination of input pins.

Maximum Differential Common Mode Voltage (Maximum Voltage be­tween T1 and T2 during measurement): 1volt.
Reading Rate: one time per second.
Input Connector: MTP miniature RTD 3 prong connector.

2

ENVIRONMENTAL

Ambient Operating Ranges: 0°C to 50°C (32°F to 122°F) <80% R.H.
Storage Temperature: -20°C to 60°C (-4°F to 140°F) <70% R.H.

GENERAL
Display: 4½ digit liquid crystal display (LCD) with maximum reading of 19999.
Overload: "----.-" is display.
Battery: Standard 9V battery.
Battery Life: 100 hours typical.
Auto power off: The meter key switch inactive for more than 30 minutes,

press power key to resume operation.

Dimensions: 192mm(H) x 91mm(W) x 52.5mm(D).
Weight: 365g.

3

OPERATING INSTRUCTIONS

1

Power Switch

The key turns the thermometer on or off. In the data SET mode, can not
power off, must leave data SET mode then power off.

2

°C/°F Selecting the Temperature Scale (Main display)

Reading the main displayed in either degrees Celsius(°C) or degrees
Fahrenheit(°F). When the thermometer is turned on, it is set to the
temperature scale that was in use when the thermometer was last turned
off. To change the temperature scale, press the °C/°F key.

3

HOLD Mode (only Main display)

Pressing the HOLD key to enter the Data Hold mode, the
"HOLD" annunciator is displayed. When HOLD mode is selected, the
thermometer held the present readings and stops all further measure­ments.
Pressing the HOLD key again to cancel HOLD mode causing thermometer
to resume taking measurements.
In the MIN/MAX recording mode, press HOLD key to stop the recording.
Press HOLD key again to resume recording. (Previously recorded reading
are not erased).

4

Relative value Recall display mode.

Press REL RECALL key to display the Relative set value on second display.
Press REL RECALL key again to exit this mode.

4

5

Pt385/Pt3926 T1 Input RTD Probe Select

The Pt385/Pt3926 key switch the T1 input selects the Pt385 or Pt3926 RTD
probe as input.
When the thermometer is turned on, it is set to the probe selected that was
in use when the thermometer was last turned off.

MIN MAX with Time record Mode

6

Press MIN MAX key to enter the MIN MAX Recording mode, (displays the
Maximum reading with time, Minimum reading with time and Average
reading stored in record mode). In the this mode the automatic power-off
feature is disabled and key, °C/°F key, REL key, SET key, Hi/Lo LIMITS
key, Pt385/Pt3926 and all RECALL keys are disabled.
The beeper emits a tone when a new minimum or maximum value is
recorded.
Present temperature reading displayed on second display.
Push MIN MAX key to cycle through the MAX, MIN and AVG readings.
If an overload is recorded, the averaging function is stopped and average
value display"----.-".
The true average of all the reading taken over at least 22 hours preiod can
be displayed. If 22 hours is exceeded, new averages are no longer
calculated. The last calcalated value is retained as the average reading, but
the actual minimum and maximum reading will continue to be captured.
In the this mode, press HOLD key to stop the recording of readings, all
values are frozen, press again to restart recording.
To prevent accidental loss of MIN, MAX and AVG data, in this mode can only
be cancelled by pressing and hold down the MIN MAX key for 2 seconds to
exit and erased recorded readings.

5

7

REL Relative mode

Pressing REL key to enter the Relative mode, zero the display, and store
the displayed Reading as a reference value and annunciator REL is
displayed. Present temperature reading displayed on second display.
Press REL key again to exit the relative mode.
The relative value can also be entered by the user. (See "SET mode" later
in this manual.)
When the desired Relative value has been entered, press REL key to enter
the Relative mode, press SET key use set Relative value as a reference
value. Press REL key again to exit the relative mode.
In the Relative mode, the value (can not >±3000.0 counts) shown on the
LCD is always the difference between the stored reference and the present
reading.

8

°C/°F Selecting the Temperature Scale (Second display)

Readings the second displayed in either degrees Celsius(°C) or degrees
Fahrenheit(°F). When the thermometer is turned on, it is set to the
temperature scale that was in use when the thermometer was last turned
off. To change the temperature scale, press the °C/°F key.

6

9

SET mode (Relative value set, Time set and Hi/Lo

1. Press SET key to enter Relative valuse SET mode (Press ENTER key can

escape relative valuse set mode), REL set mode. = = = =.= is displayed in
main display.
Relative value is entered via overlay numbers, then press overlay ENTER
key, stored the relative value, enter Time set mode.

2. Time set mode, (Press ENTER key can escape Time set mode)

=.= = = : = = is displayed in second and third display. Time (hours, minutes,
seconds) value is entered via overlay numbers, then press overlay ENTER
key. Time start from set time value, enter Hi/Lo Limits value set mode.

Limits value set)

3. Hi Limit value set mode,

Limit value set mode), = = = =.= is displayed in main display, Hi Limit value
is entered via overlay numbers, then press overlay ENTER key, stored the
Hi Limit value, enter Lo Limit value set mode (Press ENTER key can escape
Lo Limit value set mode). = = = =.= is displayed in main display, Lo Limit
value is entered via overlay numbers, then press overlay ENTER key,
stored the Lo Limit value and exit SET mode.

4. When the thermometer is turned on. The Relative set value and Hi/Lo Limits

set value that was in use when thermometer was last turned off set values.

is displayed (Press ENTER key can escape Hi

7

10

Hi Limit value Recall display mode

Press Hi RECALL key to display the Hi set Limit value on second display.
Press Hi RECALL key again to exit this mode.

Lo Limit value Recall display mode

11

Press Lo RECALL key to display the Hi set Limit value on second display.
Press Lo RECALL key again to exit this mode.

Hi/Lo Limits mode (only Main display)

12

Press Hi/Lo Limits key to enter the Hi/Lo Limits comparative mode, when
input temperature value exceed Hi or Lo Limits value. The beeper emits a
continuity pulse tone. Press Hi/Lo Limits key again to exit the Hi/Lo Limits
mode.

8

OPERATOR MAINTENANCE

WARNING

To avoid possible electrical shock, disconnect the thermocouple

connectors from the rmometer before removing the cover.

Battery Replacement

Power is supplied by a 9 volt "transistor" battery. The " " appears on the LCD
display when replacement is needed. To replace the battery, remove the two
screws from the back of the meter and lift off the battery cover. Remove the
battery from battery contacts.

RTD PROBE CONNECTION

P/N : 17650-0505

RW1

+

G

+

-

RW1=RW2=RW3
RW= WIRE RESISTANCE

RW2

-

RW3

G

9

RTD

100W

Pt385

(Pt3926)

TEMPERATURE VS RESISTANCE TABLE(ITS90)

°C Pt385 Pt3926

-200°C 18.521W 16.996W

-100°C 60.256W 59.479W
0°C 100.000W 100.000W

100°C 138.505W 139.272W
200°C 175.856W 177.362W
300°C 212.052W 214.275W
400°C 247.092W 250.018W
500°C 280.977W 284.591W
600°C 313.708W 317.994W
700°C 345.280W -
800°C 375.700W -

10

HH 504 / HH 505 CALIBRATION PROCEDURE

Note: The following calibration procedure should perform only by qualified technicians

who have access to the items as following.

Equipment: The class of calibrator had better 10 times greater than the measured meter.

1. Turn off the meter then set the adjusted jumper to J1.

2. Insert the 383.00Ω calibrator to the T1 then turn on the meter, the main
display reading reads 1830.0 then press " ENTER " key.

3. The second display is stabilized (about 5sec.), then press " ENTER " key
when the meter auto power off then set the jumper back to J3 position.

4. Turn on the meter then Insert the 100.00Ω calibrator. The display reading
reads 0°C if the calibration procedure is right.

383.00W CALIBRATOR

RW1

+

G
+
_

_

RW2

RW3

G

℃

-200℃ 18.521Ω 16.996Ω

-100℃ 60.256Ω 59.479Ω
0℃ 100.000Ω 100.000Ω

100℃ 138.505Ω 139.272Ω
200℃ 175.856Ω 177.362Ω
300℃ 212.052Ω 214.275Ω
400℃ 247.092Ω 250.018Ω
500℃ 280.977Ω 284.591Ω
600℃ 313.708Ω 317.994Ω
700℃ 345.280Ω

Pt385 Pt3926

383.00W

―

RW1=RW2=RW3
RW=WIRERESISTANCE

800℃ 375.700Ω

1

―

OMEGA ENGINEERING, INC. warrants this unit to be free of defects in materials and workmanship for a period of 13 months
from date of purchase. OMEGA Warranty adds an additional one (1) month grace period to the normal one (1) year product
warranty to cover handling and shipping time. This ensures that OMEGA's customers receive maximum cov erage on each product.If
the unit should malfunction, it must be returned to the factory for evaluation. OMEGA's Customer Service Department will issue an
Authorized Return (AR) number immediately upon phone or written request. Upon examination by OMEGA, if the unit is found to
be defective it will be repaired or replaced at no charge. OMEGA's W ARRANTY does not apply to defects resulting from any action
of the purchaser, including but not limited to mishandling, improper interfacing, operation outside of design limits, improper repair,
or unauthorized modification. This WARRANTY is V OID if the unit shows e vidence of having been tampered with or shows evidence
of being damaged as a result of excessive corrosion; or current, heat moisture or vibration; improper specification; misapplication;
misuse or other operating conditions outside of OMEGA's control. Components which wear are not warranted, including but not
limited to contact points, fuses, and triacs.

OMEGA is pleased to offer suggestions on the use of its various products. However , OMEGA neither assumes responsibility
for any omissions or errors nor assumes liability for an y damages that result fr om the use of its products in accordance
with information provided by OMEGA, either verbal or written. OMEGA warrants only that the parts manufactured by it
will be as specified and free of defects. OMEGA MAKES NO OTHER WARRANTIES OR REPRESENTATIONS OF ANY KIND
WHATSOEVER, EXPRESSED OR IMPLIED, EXCEPT THAT OF TITLE AND ALL IMPLIED WARRANTIES INCLUDING ANY
WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED.
LIMITATION OF LIABILITY: The remedies of purchaser set forth herein are exclusive and the total liability of OMEGA with
respect to this order, whether based on contract, warranty, negligence, indemnification, strict liability or otherwise, shall
not exceed the purchase price of the component upon which liability is based. In no event shall OMEGA be liable for
consequential, incidental or special damages.

CONDITIONS: Equipment sold by OMEGA is not intended to be used, nor shall it be used: (1) as a "Basic Component" under 10
CFR 21 (NRC), used in or with any nuclear installation or activity; or (2) in medical applications or used on humans. Should any
Product(s) be used in or with any nuclear installation or activity, medical application, used on humans, or misused in any way,
OMEGA assumes no responsibility as set forth in our basic WARRANTY / DISCLAIMER language, and additionally, purchaser will
indemnify OMEGA and hold OMEGA harmless from any liability or damage whatsoever arising out of the use of the Product(s) in
such a manner.

Direct all warranty and repair requests/inquiries to the OMEGA Customer Service Department. BEFORE RETURNING ANY
PRODUCT(S) TO OMEGA, PURCHASER MUST OBTAIN AN AUTHORIZED RETURN (AR) NUMBER FROM OMEGA'S
CUSTOMER SERVICE DEPARTMENT (IN ORDER TO AVOID PROCESSING DELAYS). The assigned AR number should then
be marked on the outside of the return package and on any correspondence.
The purchaser is responsible for shipping charges, freight, insurance and proper packaging to prevent breakage in transit.

FOR WARRANTY RETURNS, please have the f ollowing

information available BEFORE contacting OMEGA:

1. P.O. number under which the product was PURCHASED.

2. Model and serial number of the product under warranty, and

3. Repair instructions and/or specific problems relative to the
product.

OMEGA's policy is to make running changes, not model changes, whenever an improvement is possible. This affords our customers the latest
in technology and engineering. OMEGA is a registered trademark of OMEGA ENGINEERING, INC. © Copyright 1999 OMEGA ENGINEERING,
INC. All rights reserved. This document may not be copied, photocopied, reproduced, translated, or reduced to any electronic medium or
machine-readable from, in whole or in part, without prior written consent of OMEGA ENGINEERING, INC.

WARRANTY / DISCLAIMER

RETURN REQUESTS / INQUIRIES

FOR NON-WARRANTY REPAIRS, consult OMEGA for

current repair charges. Have the following information
available BEFORE contacting OMEGA:

1. P.O. number to cover the COST of the repair.

2. Model and serial number of product , and

3. Repair instructions and/or specific problems relative to the
product.

Where Do I Find Everything I Need for

Process Measurement and Control?

OMEGA...Of Course!

TEMPERATURE

þ Thermocouple, RTD & Thermistor

Probes, Connectors, Panels & Assemblies

þ Wire: Thermocouple, RTD & Thermistor

þ Calibrators & Ice Point References

þ Recorders, Controllers & Process Monitors

þ Infrared Pyrometers

PRESSURE/STRAIN AND FORCE

þ Transducers & Strain Gauges

þ Load Cells & Pressure Gauges

þ Displacement Transducers

þ Instrumentation & Accessories

FLOW/LEVEL

þ Rotameters, Gas Mass Flowmeters

& Flow Computers

þ Air Velocity Indicators

þ Turbine/Paddlewheel Systems

þ Totalizers & Batch Controllers

pH/CONDUCTIVITY

þ pH Electrodes, Testers & Accessories

þ Benchtop/Laboratory Meters

þ Controllers, Calibrators, Simulators

& Pumps

þ Industrial pH & Conductivity Equipment

M-2810/0799

DATA ACQUISITION

þ Data Acquisition &

Engineering Software

þ Communications-Based

Acquisition Systems

þ Plug-in Cards for Apple, IBM

& Compatibles

þ Datalogging Systems

þ Recorders, Printers & Plotters

HEATERS

þ Heating Cable

þ Cartridge & Strip Heaters

þ Immersion & Band Heaters

þ Flexible Heaters

þ Laboratory Heaters

ENVIRONMENTAL
MONITORING AND CONTROL

þ Metering & Control Instrumentation

þ Refractometers

þ Pumps & Tubing

þ Air, Soil & Water Monitors

þ Industrial Water & Wastewater

Treatment

þ pH, Conductivity & Dissolved Oxygen

Instruments