Omega Products FPU5-MT-110 User Manual

OMEGAFLEX® PERISTALTIC PUMP

FPU500

U Stainless Steel Rotor Assembly U Ideal for Use in Sterile, Corrosive or

General Operating Environments

U Flow Rates from 1.0 to 2280 mL/Min

(36 GPH)

U Mounts Directly onto OMEGAFLEX

Motor or Compatible Pump Motor

U Easily Stackable Mounting for

Multichannel Pumping

U Three-Roller Geometry Reduces

Pulsation and Improves Priming

U Polysulfone Housing for Durability

and Chemical Resistance

The FPU500 Series peristaltic pumps from OMEGA® offer exceptional simplicity, ease of use, and variable ﬂow capability. A motor turns the pump’s rollers, which squeeze ﬂuid through precision-bore tubing in a wavelike motion. The ﬂuid does not come into contact with the pump; only the outside wall of the tubing does. This makes these pumps ideal for use in sterile, corrosive, or general ﬂuid ﬂow operating environments.

The pump is self-priming and non-siphoning. When one section of the tube fatigues, simply move the tube along to an unused section and continue pumping. No tools are required to load the tube. A precision-molded tubing cavity provides the proper occlusion for the recommended tubing. A tube clamp holds the tubing securely in place. Tubing is easily changed without removing the pump.

One pump can be used for many different applications, or you can mount two pumps onto the motor. The pumps work with a wide variety of OMEGAFLEX silicone, Santoprene, and Norprene

plastic tubing. Vinyl, FKM, Tygon,

tubing can be purchased in a broad range of sizes. The standard rotor assembly is made of stainless steel.

The FPU500 pump can be purchased with an optional adaptor plate that can be used to mount the pump to a motor other than the FPU5-MT pump motor. The pump comes standard with 2 short mounting screws, used to mount one pump at a time. If you need to stack two pumps, order long mounting screws.

FPU500 shown smaller than actual size.

SPECIFICATIONS

Maximum Back Pressure: 20 psi Maximum RPM to Prime: 100 RPM Tube Wall: 1.6 mm ( Fluid Temperature Range: -46 to 149°C (-50 to 300°F) Dimensions, Pump: 102 H x 102 W x 57 mm D (4 x 4 x 2 Optional Mounting Plate: 76 H x 64 W x 3.2 mm D

⁄2 x 1⁄8")

(3 x 2

Weight, Pump: 408 g (14.4 oz) Optional Mounting Plate: 91 g (32 oz) Maximum Tubing Size: 8 mm ( Maximum Tube Durometer: 65 Shore A

Tube Tubing Maximum Flowrate Wall (inch) Size (inch) mL/Rev. @ 600 RPM, mL/min

¹⁄₁₆

⁄16")

¹⁄₃₂

0.05 30

¹⁄₁₆

0.22 132

¹⁄₈

0.9 540

³⁄₁₆

1.9 1140

¹⁄₄

3.0 1800

⁵⁄₁₆

3.8 2280

⁄4")

Changing Tubing Is a Snap! Just Follow These Four Easy Steps:

Step 1: Snap Open with Easy Push-Button Release

Step 2: Loop Tubing Over Rollers. No Need to Thread!

Step 3: Push to Close

L-23

Step 4: Tighten Screw to Secure Tubing

OMEGAFLEX® PUMP MOTOR

FPU5-MT-Series

975

FPU5-MT-110 pump motor, shown smaller than actual size, with two FPU500 pumps.

U Digital Display of Flow Rate, RPM, Total

Volume, Fluid Temperature (°C or °F), Flow Duration, or Tube ID

U Flow Rate 1.0 to 2280 mL/Min

(10 to 600 RPM) Reversible

U Easy-to-Read Display U Rear Panel Type K SMP Female

Thermocouple Input

U Tachometer Feedback,

±0.5% Speed Control

U Accepts Two Pumps, One on Each Side

or Two Stacked Together

U Membrane Keypad for Easy Calibration U Remote Control Capabilities

• Aux. In: Remote Start/Stop

• Aux. Out: Remote Monitor

U Built-In Electronic Braking and

Reversing for Fast Stops and Directional Changes

U Accepts Metric or English Tube Sizes U Displays Information in English,

French, Spanish, German, or Italian

Calibrating the unit is easy with the user-friendly control software. Simply select a tubing size and the desired ﬂow rate, and the pump motor locks in the required RPM. Select nominal calibration values stored in ROM (read only memory) or calibrate via gravimetric or ﬂowmeter measurements. Fluid temperature may be displayed (using an optional thermocouple probe). The last ﬂow settings are stored in memory when the drives are shut off.

SPECIFICATIONS

Motor: Reversible, 1⁄10 HP (75 W), 90 Vdc Display: 16-character dot matrix LCD, 9 mm H ( Power: 90 to 130 Vac, 1.5 A; 190 to 260 Vac, 0.8 A Line Cord: 1.8 m (6') with U.S. standard plug on 115 Vac

units; European plug on 230 Vac units Housing: Painted sheet metal with rubber feet; units are stackable

Dimensions: 152 H x 254 W x 254 mm D (6 x 10 x 10") Weight: 8.2 kg (18 lb)

⁄8") characters

To Order Visit omega.com/fpu500 for Pricing and Details

Model No. Description

FPU5-MT-110 Pump motor (110 Vac)

FPU5-MT-220 Pump motor (220 Vac)

FPU500 Peristaltic pump

The OMEGAFLEX® FPU5-MT pump motor offers microprocessor control and a digital display, and is designed to be fully compatible with OMEGA’s FPU500 pump. No mounting plate is needed, just two mounting screws. A 2280 mL/minute. The user enters values and controls all operations through a convenient membrane keypad. A dot matrix LCD provides for easy viewing.

⁄10 HP (75 W) motor provides ﬂow rates of up to

L-24

Accessories

Model No. Description

FPU500-AP Adaptor plate

FPU500-LMS Long mounting screws (2)

FPU500-SMS Short mounting screws (2)

FPU500-RA Replacement rotor assembly

Comes complete with operator’s manual. Ordering Example: FPU5-MT-110, pump motor and, FPU500,

peristaltic pump.