Omega Products FPD2001-A User Manual

POSITIVE DISPLACEMENT FLOWMETERS

FPD2000 Series

U ±0.5% Rdg Accuracy U Aluminum, 303 or 316 SS Bodies U Pressure Rating Up to 345 bar (5000 psi)

FPD2004-A shown smaller than actual size.

U Pulse or mA Outputs Available U Bi-Directional Flow Capabilities U Economical Cost

The FPD2000 Series represents a positive displacement meter that is affordable and accurate. One primary feature is the ability to maintain consistent accuracy despite changing viscosity conditions. This reliability, coupled with a large turndown range, offers an affordable replacement for older turbine technology. The meter’s solid construction and excellent dynamic response are well suited to the measurement of oil, grease, fuel, solvents, polyurethanes, brake ﬂuid, skydrol as well as other nonabrasive lubricating ﬂuids. Since there is no need for straight run piping upstream or downstream of the ﬂowmeter, the FPD2000 ﬂowmeters are simple to use and to install. The meters produce good resolution and high accuracy at low ﬂow rates. Flow may be bi-directional, such as for cylinder position measurements, without damage to internal parts.

SPECIFICATIONS

Accuracy: ±0.5% over 10:1 turndown with 30cP ﬂuid Repeatability: ±0.1% Max Fluid Temperature:

Aluminum Body: Meter 85°C (185°F) Stainless Body: Meter 204°C (400°F) Pressure Maximum: 345 bar (5000 psi) Wetted Materials

Body:

FPD2000 Series: Aluminum

FPD2010 Series: 303 SS FPD2020 Series: 316 SS

Gear: Stainless steel O-Ring: PTFE, FKM (optional) Bearings: Stainless steel

Outputs

Temperature Range (Electronics): Standard Aluminum

and SS versions -40 to 85°C (-40 to 185°F)

*Body Height Filtration Model No. Pulses/Liter (Pulses/Gallon) Body Dia cm (inch) cm (inch) (microns)

FPD20X1 14,000 (53,000) 7.6 (3) 8.6 (3.4) 30 FPD20X2 4200 (15,900) 8.4 (3.3) 8.6 (3.4) 30 FPD20X3 1700 (6600) 8.4 (3.3) 8.6 (3.4) 30 FPD20X4 470 (1800) 12.4 (4.9) 13.8 (5.45) 30 FPD20X5 420 (1600) 21.3 (8.4) 17 (6.7) 200

On analog output models (FPD2XXX-A) add 12 cm (4.8") to the body height to obtain overall height.

Stainless Steel Versions with -HT Option:

-40 to 204ºC (-40 to 400ºF)

Square Wave: (Basic unit) Supply Voltage: +10 to 28 Vdc Supply Current: 8 mA @ 12 Vdc,12 mA @ 24 Vdc Duty Signal: 50% ±15% Minimum Signal: 0.5 Hz Frequency: Flow dependent, up to 2000 Hz Driving Capacity: 50 mA max resistive load Output Impedance: 40 Ω - analog switch and

self-resetting fuse

Analog Output (-A Models)

Supply Voltage: 10 to 30 Vdc Output: 4 to 20 mA Input: 0.25 Hz to 5 kHz Amplitude: 1 to 40 Vp-p Update Time: 1/F + 25 msec Linearity: ±0.01% rdg Enclosure Certifcations: NEC Class 1 groups C, D,

Class 2 groups E, F, G

F-75

FPD2005 shown smaller than actual size.

DPF701 shown smaller than actual size, visit omega.com/dpf701.

To Order Visit omega.com/fpd2000_series for Pricing and Details

Model No. NPT Range LPM (GPM) Description

FPD2001 ¹⁄₄ 0.01 to 3 (0.003 to 0.8) Aluminum gear meter with pulse output FPD2002 ¹⁄₄ 0.04 to 7.5 (0.01 to 2) Aluminum gear meter with pulse output

FPD2003 ¹⁄₂ 0.11 to 26.4 (0.03 to 7) Aluminum gear meter with pulse output FPD2004 ³⁄₄ 0.19 to 75 (0.05 to 20) Aluminum gear meter with pulse output FPD2005 1¹⁄₄ 1.9 to 227 (0.5 to 60) Aluminum gear meter with pulse output FPD2001-A ¹⁄₄ 0.01 to 3 (0.003 to 0.8) Aluminum gear meter with 4 to 20 mA output FPD2002-A ¹⁄₄ 0.04 to 7.5 (0.01 to 2) Aluminum gear meter with 4 to 20 mA output FPD2003-A ¹⁄₂ 0.11 to 26.4 (0.03 to 7) Aluminum gear meter with 4 to 20 mA output FPD2004-A ³⁄₄ 0.19 to 75 (0.05 to 20) Aluminum gear meter with 4 to 20 mA output FPD2005-A 1¹⁄₄ 1.9 to 227 (0.5 to 60) Aluminum gear meter with 4 to 20 mA output FPD2011 ¹⁄₄ 0.01 to 3 (0.003 to 0.8) 303 SS gear meter with pulse output FPD2012 ¹⁄₄ 0.04 to 7.5 (0.01 to 2) 303 SS gear meter with pulse output FPD2013 ¹⁄₂ 0.11 to 26.4 (0.03 to 7) 303 SS gear meter with pulse output FPD2014 ³⁄₄ 0.19 to 75 (0.05 to 20) 303 SS gear meter with pulse output FPD2015 1¹⁄₄ 1.9 to 227 (0.5 to 60) 303 SS gear meter with pulse output FPD2011-A ¹⁄₄ 0.01 to 3 (0.003 to 0.8) 303 SS gear meter with 4 to 20 mA output FPD2012-A ¹⁄₄ 0.04 to 7.5 (0.01 to 2) 303 SS gear meter with 4 to 20 mA output FPD2013-A ¹⁄₂ 0.11 to 26.4 (0.03 to 7) 303 SS gear meter with 4 to 20 mA output FPD2014-A ³⁄₄ 0.19 to 75 (0.05 to 20) 303 SS gear meter with 4 to 20 mA output FPD2015-A 1¹⁄₄ 1.9 to 227 (0.5 to 60) 303 SS gear meter with 4 to 20 mA output FPD2021 ¹⁄₄ 0.01 to 3 (0.003 to 0.8) 316 SS gear meter with pulse output FPD2022 ¹⁄₄ 0.04 to 7.5 (0.01 to 2) 316 SS gear meter with pulse output FPD2023 ¹⁄₂ 0.11 to 26.4 (0.03 to 7) 316 SS gear meter with pulse output FPD2024 ³⁄₄ 0.19 to 75 (0.05 to 20) 316 SS gear meter with pulse output FPD2021-A ¹⁄₄ 0.01 to 3 (0.003 to 0.8) 316 SS gear meter with 4 to 20 mA output FPD2022-A ¹⁄₄ 0.04 to 7.5 (0.01 to 2) 316 SS gear meter with 4 to 20 mA output FPD2023-A ¹⁄₂ 0.11 to 26.4 (0.03 to 7) 316 SS gear meter with 4 to 20 mA output FPD2024-A ³⁄₄ 0.19 to 75 (0.05 to 20) 316 SS gear meter with 4 to 20 mA output

Accessories

Model No. Description

DPF701 Pulse input 6-digit panel meter for rate or total, visit omega.com/dpf701 FPD2000-CONNECTOR Replacement 6-pin connector for the FPD2000 pulse output models FPD2000A-CONNECTOR Replacement 3-pin connector for the FPD2000-A 4 to 20 mA output models

Comes complete with operator’s manual, K-factor certiﬁcate, and connector. Certiﬁcate does not include points and is not a NIST certiﬁcate. FPD2000, pulse output models, come with the 6-pin FPD2000-CONNECTOR.

FPD2000-A, 4 to 20 mA output models, come with the FPD2000A-CONNECTOR. For High Temperature option on stainless steel models, add sufﬁx “-HT” to model number, for additional cost. Ordering Examples: FPD2003, aluminum gear meter with pulse output,

⁄

DIN panel meter with red LED display.

FPD2012-A, 303 SS gear meter with 4 to 20 mA output,

NPT, 0.01 to 2 GPM range.

⁄

NPT connections, 0.03 to 7 GPM range and DPF701 digital

F-76