Omega Products FL-3207C User Manual

65 AND 150 mm ROTAMETERS

Dimensions show flowmeter side view. Face width (not shown) is 32 mm (1.25"). Use center line dimensions for drilling panel.

Drill two 15 mm (0.59'') holes to fit inlet and outlet. Maximum panel thickness is 9.5 mm (0.375"). Use the 2 retaining nuts supplied to secure flowmeter.

(1.85)

open

(1.13)

(0.55)

12.7

(0.50)

(4.25)

size

Center

Line

9.5

(0.375) maximum

panel thickness

(0.625)

Featuring Standard Industrial Dimensions and Superior Readability

U Up to ±2% FS Accuracy U Non-Rotating Seal

Spindle

U Easy-to-Read

Scale Design

U Special Dimensions for

Interchangeability

The OMEGA® precision variablearea rotameters can measure ﬂows of air, water, and gases, with up to ±2% FS accuracy (models ending in “07” or “45” have ±5% FS accuracy) and 0.25% FS repeatability. These units feature an easy-to-read millimeter scale and come with correlation charts for air and water. The scale is fused on the metering tube in 1 mm (³⁄₃₂") increments, which enables a user to read the ﬂow rate with the highest accuracy.

The scale design, in which a vertical line runs through the length of the scale and intersects the horizontal scale divisions, reduces parallax and eye fatigue, thus ensuring high-accuracy readings (see inset, next page). The front polycarbonate resin shield is also curved to act as a magnifying glass, which yields superior performance over other rotameters with standard designs

Non-Rising Stem Needle Valve

The 150 mm size ﬂowmeters are also available with a non-rising stem type needle valve for special applications. This 15-turn metering valve has superior ﬂow-rate control, and is particularly suited to use in chromatography applications. The sliding tapered-needle mechanism virtually eliminates sticking or buildup due to foreign matter in the ﬂuid stream, without variations or saw-toothing of the ﬂow rate.

FL-3207G

Optional

shown larger

than actual size.

Shielded for Pressurized Systems

These rotameters, with precisionbored borosilicate glass metering tubes, are fully shielded against breakage. A white opaque rear shield provides a background to aid in discerning the ﬂoat position.

Panel Mounting Design

These rotameters are equipped with horizontal ports and NPT threads for easy panel mounting. The ports have external threads and are equipped with panel retaining nuts. No additional mounting hardware is required. Simply drill 2 holes 131 mm (5.156") apart (center to center) for 65 mm units, 240 mm (9.469") apart (center to center) for 150 mm units. Each hole should be 16 mm (5⁄8") in diameter.

SPECIFICATIONS

Scales: 65 or 150 mm

arbitrary scale

Accuracy: ±2% FS (*±5% FS) Repeatability: ± Connections: Flow Tube: Borosilicate glass End Fittings: Anodized aluminum

or 316 SS

Side Panels: Aluminum Valve Oriﬁce: Polyacetal for

aluminum models, PCTFE 316 SS models O-Rings: Buna in aluminum models, FKM in 316 SS models

Packings: FKM Float Stops: PTFE Maximum Temperature:

250°F (180°F for water)

Maximum Pressure: 200 psig Valve Oriﬁce: Polyacetal for

aluminum units, PCTFE for 316 SS

⁄4% FS

⁄8 FNPT, horizontal

for

B-21

FL-3207G

Panel-Mount Installation

Dimensions: mm (inch)

Rotameters with 65 mm Flow Tubes

To Order Visit omega.com/fl3200_fl3500 for Pricing and Details

Model No. Model No. Aluminum Frame 316 SS Frame

Air Water FL-3207G* FL-3307G* 5.77 0.07 FL-3207ST* FL-3307ST* 16.77 0.28

FL-3207C* FL-3307C* 32.99 0.62 FL-3235G FL-3335G 48.7 0.59 FL-3235ST FL-3335ST 214.5 2.38

FL-3207G shown larger than actual size.

FL-3213G FL-3313G 104 1.75 FL-3213ST FL-3313ST 298 5.78

FL-3210G FL-3310G 202 2.64 FL-3210ST FL-3310ST 522 12.0 FL-3210C FL-3310C 818 20.8 FL-3251G FL-3351G 986 20.5

FL-3251ST FL-3351ST 1946 55.6 FL-3292G FL-3392G 1249 26.97 FL-3292ST FL-3392ST 2520 70.67 FL-3292C FL-3392C 3680 03.5 FL-3288G FL-3388G 2040 39.7

FL-3288ST FL-3388ST 3980 108.3 FL-3288C FL-3388C 5739 169.8 FL-3265G FL-3365G 2678 52.0 FL-3265ST FL-3365ST 4922 150.0 FL-3296ST FL-3396ST 12,058 364.0 FL-3217ST FL-3317ST 24,680 745.0 FL-3263ST FL-3363ST 42,094 1261.0 FL-3263C FL-3363C 58,500 1866.0

Rotameters with 150 mm Flow Tubes

Model No. Model No. Aluminum Frame 316 SS Frame

Max

FL-3445G* FL-3545G* 18.6 0.196

FL-3445ST* FL-3545ST* 61.8 0.956

FL-3445C* FL-3545C* 110 1.92 FL-3441G FL-3541G 48.5 0.53 FL-3441ST FL-3541ST 141.5 2.45

Polycarbonate resin shield acts as a magnifier to ensure high accuracy with less eye fatigue.

FL-3461G FL-3561G 92 0.85 FL-3461SA FL-3561SA 140 1.92

FL-3461ST FL-3561ST 263 4.7 FL-3461C FL-3561C 454 8.5 FL-3402G FL-3502G 374 5.5 FL-3402ST FL-3502ST 814 20.4

FL-3402C FL-3502C 1222 33.7 FL-3403G FL-3503G 825 16.5 FL-3403ST FL-3503ST 1682 46.0 FL-3404G FL-3504G 2313 53.5 FL-3404ST FL-3504ST 4562 130.4

FL-3405G FL-3505G 3807 84.3 FL-3405ST FL-3505ST 7590 216.6 FL-3439G FL-3539G 8678 210.0 FL-3439ST FL-3539ST 16,737 506.0 FL-3440G FL-3540G 22,536 54.0 FL-3440ST FL-3540ST 41,512 1288.0 FL-3440C FL-3540C 59,494 1881.0

Comes complete with correlation tables (one each for air and water) on the back of the instruction sheet. G suffix denotes glass float, ST suffix denotes 316 SS float, C suffix denotes carboloy float, SA suffix denotes sapphire float.

For units without valve, add suffix “-NV” to model number.

For 16 turn, high-resolution non-rising stem valve for 150 mm rotameters, add suffix “-HRV” to model number, for

additional cost.

†

Minimum flow rate is 10% of maximum.

Accuracy ±5% on these models.

For NIST traceable certificate for air, add suffix “-NISTAIR” to model number, for additional cost. For water, add suffix “-NISTWATER” to model number, for additional cost.

Ordering Examples: FL-3403ST, 150 mm flowtube in aluminum frame. FL-34406-NV, 150 mm flowtube in aluminum frame, no valve. FL3502G-HRV, 150 mm flowtube in 316 SS frame with high resolution valve.

B-22

Max Flow Rate† (cc/min)

Flow Rate† (cc/min)

Air Water