Page 1
AP24MT, AP24ET,
AP15ET, AP10ET
Convection Panel Heaters
Instruction
Manual
Page 2
omega altise
2
Important Safety Instructions
1. Disconnect the power plug before dismantling, assembling or before cleaning.
2. Make sure the heater is on a dry and even surface.
3. Always use the heater in an upright position.
4. Do not insert or allow foreign objects to enter any ventilation or exhaust opening, as this may cause an electric
shock, fire or damage to the appliance.
5. This appliance is not intended for use by persons (including children) with reduced physi cal, sen sory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
6. Children should be supervised to ensure that they do not play with the appliance.
7. The heater must not be located immediately below a socket-outlet;
8. Do not use this heater in the immediate surroundings of a bath, a shower, or a swimming pool;
9. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified
persons in order to avoid a hazard;
10. Do not use your appliance with an extension cord unless it has been checked and tested by a qualified electrician
or electrical supplier.
11. Do not use the appliance for any other purpose than its intended use.
12. Do not position the appliances in close proximately to curtains or other combustible materials. Keep combustible
material such as furniture, cushions, bedding, paper, clothes, curtains etc. at least 1.0m away from the heater.
13. Do not operate in areas where gasoline, paint or other flammable liquids are used or stored.
14. Do not use the appliance in rooms less than 4m
2
area.
CAUTION: In order to avoid a hazard due to inadvertent resetting of the thermal cutout, this appliance must
not be supplied through an external switching device such as a timer, or connected to a circuit that is
regularly switched on and off by the utility.
WARNING: IN ORDER TO AVOID OVERHEATING, DO NOT COVER THIS HEATER
Read all instructions before using this unit. Keep them for future reference.
Page 3
omega altise
3
Specifications
Model AP24MT AP24ET AP15ET AP10ET
Rated Voltage 240V / 50Hz 240V / 50Hz 240V / 50Hz 240V / 50Hz
Watts 2400W 2400W 1500W 1000W
Controls Manual Manual Manual Manual
Thermostat Mechanical Electronic (5-30o) Electronic (5-30o) Electronic (5-30o)
Heating Element Sheathed heating element with aluminium diffuser (safe, silent and long-lasting)
24hr Timer
9 9 9 9
Wall Mountable
9 9 9 9
Castors
9 9 9 9
Safety Features
Safety cut-out; Control box
cover; Lockable castors
Safety cut-out; Control box
cover; Lockable castors
Safety cut-out; Control box
cover; Lockable castors
Safety cut-out; Control box
cover; Lockable castors
IP Status IP24 IP24 IP24 IP24
Measurements
(l x h x d mm)
1000 x 440 x 105 1000 x 440 x 105 740 x 440 x 105 580 x 440 x 105
Nett Weight (kg) 8.2 8.0 6.3 4.8
Warranty 7 year repair / replacement 7 year repair / replacement 7 year repair / replacement 7 year repair / replacement
M: mechanical thermostat E: electronic thermostat T: timer
Assembly Instructions
Remove all items of packaging from the panel. As this
convector panel heater is designed to be wall mounted OR
freestanding please follow the below instructions according
to your choice:
TO WALL MOUNT THE PANEL
Where to install the heater?
1. Ensure the safety zones (shown in mm) are kept free
(see Figure 1).
2. The panel convector must not be installed immediately
below a wall socket. The heater must be connected to
a socket outlet or permanent terminal box at least
10cm to one side of the heater (see Figure 2).
3. If the heater is installed in the Bathroom or in a humid
area, the socket outlet or permanent terminal box must
conform to the IP24 requirement (please consult an
electrician for further details).
4. The panel convector must not be installed in a draught
likely to affect the control settings (under a ventilating
fan, etc.)
Figure 1.
Fi
g
ure 2.
Page 4
omega altise
4
Attaching the wall mounting bracket
What you will need:
1. Screwdriver
2. Pencil/pen to mark the drill holes on the wall
3. Drill
4. 4 x screws for fixing (Suggest 4mm expansion screws
for most installations).
IMPORTANT: Only use the wall mounting bracket supplied
with the unit. For your convenience, the wall mounting
bracket is oriented centrally on the back of the unit.
Figure 3.
1. Loosen the small screw used to fix the wall mounting
bracket to the back of the unit located on the top right
hand side looking from the back. Place to one side.
2. Slide the wall mounting bracket down and away from
the unit.
3. Using the wall mounting bracket as a template for
positioning, place the bracket on the bottom of the wall.
Mark the screw-holes through the holes marked A and
B as shown in Figure 3.
4. Raise the bracket so that the holes marked
C and D are aligned with the marks already made on
the wall in Step 3. Mark the upper holes through holes
E and B as shown in Figure 4.
Figure 4.
5. Drill the four holes into the wall as marked. 4mm
expansion screws are suggested for use to secure the
wall-mounting bracket to the wall.
6. The unit can now be hooked onto the wall mounting
bracket through the four slots on the back. Please refer
to the Figure 5.
7. Replace and tighten the small screw used to fix the
wall mounting bracket to the back of the unit.
8. To remove the unit reverse the above steps.
Figure 5.
TO ATTACH THE CASTORS TO USE THE
PANEL AS A PORTABLE HEATER
Parts list
Support (2pcs) Castor (4pcs) Clip (2pcs)
1. Press 2 castors into the bottom of each of the supports
as shown to the right
2. Turn the body of the unit upside down, with the front of
the unit facing away from you.
3. Place the support over the base so that the securing
hooks line up with the grille on the bottom
4. Slide the support towards to front of the unit making
sure that both lines of securing hooks are firmly in
place over the base cut outs.
5. Secure in place with the clip. Some force may be
necessary.
Page 5
omega altise
5
Operating Instructions
Preparation
Remove the screw that is used to secure the cover (1)
to the control panel in an anti-clockwise direction.
Switching on the Unit
The unit may be switched on (setting I) or off (setting
O) by using the switch (2) on the right hand side panel.
Heating
Turn the temperature selector (3) clockwise to select
the required temperature. The heater will warm the
room uniformly and quickly. Air enters the heater from
below where it is heated and then exits through the
grid at the top of the heater.
The room temperature can be set between approx.
5 °C and 30 °C. The thermostat switches the heater off
once the set temperature has been reached and
switches on and off intermittently to maintain the
required temperature.
During the first operation, the heater may
give off a smell. Ensure that the room is
well ventilated (for example, open a
window).
Timer setting
Each unit comes with a 24 hour timer (4), which
overrides the heat switches and thermostat. However,
the unit must be connected with the power supply and
switched on for the timer to work.
Manual operation
If you do not wish to use the timer function you must
push all of the time segments towards the centre and
you can manually operate the unit.
If all the time segments are pushed out, the unit will not
operate.
Automatic operation
For the unit to operate automatically, you will need to
have the unit switched on and the current time set. To
do this you will need to rotate the clock face clockwise,
until the correct time is aligned with the indicator arrow
at the top.
NB: The timer’s rotating face acts like a 24 hour
clock. The number 12 is 12pm Noon and the
number 24 represents 12am Midnight.
For times when you wish the heater to switch ON,
push the corresponding time segment towards the
centre. Each time segment represents around 15
minutes, so if you want the heater continuously ON for
2 hours, push 8 segments towards the centre face.
You can set as many ON periods as you like within a
24hr period. These settings will repeat every day until
changed.
When the power is switched OFF, or during a power
failure, the timer will stop functioning. The correct time
must be reset when power is restored.
The clock face turns CLOCKWISE ONLY.
Forcing the clock face in the other
direction will destroy timing gears and
void the product warranty
Page 6
omega altise
6
Safety Notes
Control Panel Cover
It is recommended that you use the small screw
provided to secure the control panel cover in place to
avoid children from touching the controls, or random
operation of the unit.
Air outlet
The air outlets must not be obstructed.
For safety reasons the upper and lower air grilles must
never be covered with items such as washing nor
obstructed by items in too close proximity
Objects should not be leant against the unit nor placed
between the unit and the wall.
Never leave combustible materials, such as wood,
paper, textiles or flammable items such as wax, petrol,
aerosol cans etc. in the vicinity of the warm air outlet.
Safety thermal cut-out
The panel convector heater is equipped with a safety
cut-out that switches the heater off if it overheats.
Once the heater has switched off due to overheating,
remove the cause of the fault, e. g. blocked air grids.
When the heater has cooled down for several minutes
it will restart automatically. If the heater then cuts off
again, switch off the heater and call an authorized
serviceman
Care and Maintenance
1. Always disconnect the cord from the electrical
outlet before cleaning the unit.
2. Light accumulated dust may be removed from the
upper and lower grilles with a soft cloth or vacuum
cleaner using the dusting brush attachment.
3. Wipe the exterior surfaces of the unit occasionally
with a cloth moistened (not dripping wet) with a
mild soap solution. Dry the surfaces thoroughly
with a soft dry cloth before operating.
4. Avoid the use of gasoline, benzine, thinner etc as
they may result in damage to the unit.
5. If keeping the unit as a portable heater, please
store the unit in a clean dry place when not in use.
CAUTION! Do not immerse the heater in
water or allow water to drip into the
interior of the heater housing as this
could create a fire or electric shock
hazard.
WARNING! Do not attempt to open or
repair the heater yourself. Doing so
could void the warranty and cause
damage or personal injury.
Omega Altise products are distributed in Australia by MEA,
(A Division of Hagemeyer Brands Australia Pty Ltd)
ABN 28 001 375 686
Locked Bag 4013, Kingsgrove NSW 2208
Phone: 1300 739 033
Fax: 1800 838 899
Email: customerservice@meaappliances.com.au
Web: meaappliances.com.au
Loading...