OMEGA OM-CP-RHTEMP1000IS-A2 Manual

OM-CP-RHTEMP1000IS-A2

Xxxxx Xxxxxx

Xxxxx Xxxxxx Xxxxxxxx

M0000/0016

INSTRUCTION

SHEET

Shop online at omega.comSM e-mail: [e-mail]
For latest product manuals: www.omegamanual.info

TM

Intrinsically Safe Temperature and Humidity
Data Logger with Stainless Steel Enclosure

MQS5095/0820

800898

OM-CP-RHTEMP1000IS-A2

Product Notes

The OM-CP-RHTemp1000IS-A2 carries hazardous location, intrinsically safe certification in accordance with
the latest issue of:
FM3600, FM3610, CAN/CSA-C22.2 No. 60079-0:15, CAN/CSA-C22.2 No. 60079-11:14

Certified Intrinsically Safe for:

- Class 1 Division 1 Group ABCD

- Class 1 Division 2 Group ABCD

- Temperature Class: T4A

Operational Warnings

- When used in hazardous locations, the OM-CP-RHTEMP1000IS-A2 is to be installed prior to the location
becoming hazardous and removed only after the area is no longer hazardous.

- The maximum allowed ambient temperature for the OM-CP-RHTEMP1000IS-A2 (under any circumstances) is
80 °C. The minimum rated operating temperature is -40 °C.

- The OM-CP-RHTEMP1000IS-A2 is approved for use only with the Tadiran TL-2150 battery. Replacement with
any other battery will void the safety rating.

- Batteries are user replaceable, but are to be removed or replaced only in locations known to be non­hazardous.

- Tampering or replacement of non-factory components may adversely aect the safe use of the product, and
prohibited. Except for replacement of the battery, the user may not service the OM-CP-RHTEMP1000IS-A2.
Omega or an authorized representative must perform all other service to the product.

2

OM-CP-RHTEMP1000IS-A2

Installation Guide

Installing the Software

Install Omega 4 software (see specifications for compatible versions) and USB Drivers onto a Windows PC
(Windows XP SP3 or later). Follow the instructions provided in the Installation Wizard.

Installing the Interface Cable

- OM-CP-IFC400 or OM-CP-IFC406
Follow the instructions provided in the Installation Wizard to install the USB Interface Drivers.

Device Operation

Connecting and Starting the Data Logger

- Once the software is installed and running, plug the interface cable into the docking station (OM-CP-IFC400
or OM-CP-IFC406).

- Connect the USB end of the interface cable into an open USB port on the computer.

- Place the data logger into the docking station.

- The data logger will automatically appear under Connected Devices within the software.

- For most applications, select “Custom Start” from the menu bar and choose the desired start method,
reading rate and other parameters appropriate for the data logging application and click “Start”. (“Quick
Start” applies the most recent custom start options, “Batch Start” is used for managing multiple loggers at
once, “Real Time Start” stores the dataset as it records while connected to the logger.)

- The status of the device will change to “Running”, “Waiting to Start” or “Waiting to Manual Start”,
depending upon your start method.

- Disconnect the data logger from the docking station and place it in the environment to measure.

Note: The device will stop recording data when the end of memory is reached or the device is stopped, unless user selectable
memory wrap is enabled. At this point the device cannot be restarted until it has been re-armed by the computer.

Stopping and Downloading Data from the Data Logger

- Place the logger into the docking station (OM-CP-IFC400 or OM-CP-IFC406).

- Highlight the data logger in the Connected Devices list. Click “Stop” on the menu bar.

- Once the data logger is stopped, with the logger highlighted, click “Download”. You will be prompted to
name your report.

- Downloading will ooad and save all the recorded data to the PC.

Communication
To ensure desired operation of the OM-CP-RHTEMP1000IS-A2, please keep the surface clear of any
foreign objects or substances. The OM-CP-RHTEMP1000IS-A2’s data is downloaded through external
contact with the OM-CP-IFC400 or OM-CP-IFC406 docking station. Covering the surface with foreign
objects (i.e. Calibration Labels) can prevent the communication and/or downloading process.

3

OM-CP-RHTEMP1000IS-A2

Product Maintenance

Battery Replacement

Materials: Replacement Battery Tadiran TL-2150 (OM-CP-BAT113)

- Observe Operational Warnings when removing and replacing the battery.

- Unscrew the bottom of the logger and remove the battery.

- Place the new battery into the logger. Caution: Observe correct battery polarity when installing.

- Screw the cover back onto the logger.

O-Rings

O-Ring maintenance is a key factor when properly caring for the OM-CP-RHTEMP1000IS-A2. The O-Rings
ensure a tight seal and prevent liquid from entering the inside of the device.

Recalibration

Recalibration is recommended annually for any Omega data logger; a reminder is automatically displayed in
the software when the device is due.

Still need help? For more troubleshooting tips and information, refer to the built in help section visit us online at www.omega.com

or contact us for support at 1 [phone].

4

OM-CP-RHTEMP1000IS-A2

OM-CP-RHTEMP1000IS-A2 General Specifications

Description OM-CP-RHTEMP1000IS-A2

Temperature Sensor Resistance Temperature Detector (RTD)

Temperature Range -40 °C to +80 °C (-40 °F to +176 °F)

Temperature Resolution 0.01°C (0.018 °F)

Calibrated Accuracy ±0.5 °C (0 °C to ±50 °C), ±0.9 °F (32 °F to 122 °F)

Humidity Sensor Capacitive Polymer

Humidity Range 0 %RH to 100 %RH (non-condensing)

Humidity Resolution 0.1 %RH

Calibrated Accuracy ±3.0 %RH maximum

Specified Accuracy Range

Memory 32,768 Readings

Start Modes Software programmable immediate or delay start, up to 24 months in advance

Real Time Recording May be used with PC to monitor and record data in real time

Reading Rate 1 reading every second up to 1 reading every 24 hours

Lethality Equations

Calibration Digital calibration through software

Calibration Date Automatically recorded within device and displayed in software

Time Accuracy 16 seconds / month -40 °C to 80 °C

Data Format Date and time stamped ºC, ºF, K, ºR; %RH, mg/mL, Dew Point

Required Interface Package OM-CP-IFC400 or OM-CP-IFC406

Battery Type

Baud Rate 125,000 baud

Typical Battery Life 2 years typical at 15 minute reading rate

Operating System

Compatibility

Omega Software

Compatibility

Operating Environment -40 °C to +80 °C (-40 °F to +176 °F), 0 %RH to 100 %RH (case properly sealed)

Material 316 Stainless Steel/Radel

IP Rating Not Rated - Caution: Do not submerge this product to retain IS rating

Dimensions 1.67 in x 0.97 in dia. (42.3 mm x 24.6 mm dia.)

Weight 2.4 oz (68 g)

Approvals

25 %RH to 75 %RH, +20 °C to +40 °C (68 °F to 104 °F)
Hysteresis Error 1 % Typical, 3 % Maximum

Sterilization Units and Pasteurization Units are available within software with a click of
a button

Tadiran TL-2150 (OM-CP-BAT113) 3.6 V lithium battery included, user replaceable in a
non-hazardous location

Windows XP SP3 7/8/10 or later

Standard Software version 4.2.19.1 or later
Secure Software version 4.2.18.0 or later

CE
FM Class 3600, Rev. Jan 2018
FM Class 3610, Rev. Jan 2018
CAN/CSA-C22.2 No. 60079-0:15
CAN/CSA-C22.2 No. 60079-11:14

BATTERY WARNING: Fire, explosion, and severe burn hazard. Do not short circuit, charge, force over discharge,

disassemble, crush, penetrate or incinerate. Battery may leak or explode if heated above 80 °C (176 °F).

5

Specifications subject to change. See Omega’s terms and conditions at www.omega.com

omega.com [e-mail]

TM

Servicing North America:

U.S.A. Omega Engineering, Inc.
Headquarters: Toll-Free: 1-800-826-6342 (USA & Canada only)

Customer Service: 1-800-622-2378 (USA & Canada only)
Engineering Service: 1-800-872-9436 (USA & Canada only)
Tel: [phone] Fax: [phone]
e-mail: [e-mail]

The information contained in this document is believed to be correct, but OMEGA accepts no liability for any errors it contains, and reserves the
right to alter specifications without notice.

OMEGA ENGINEERING, INC. warrants this unit to be free of defects in materials and workmanship for a period of 13 months
from date of purchase. OMEGA’s WARRANTY adds an additional one (1) month grace period to the normal one (1) year product
warranty to cover handling and shipping time. This ensures that OMEGA’s customers receive maximum coverage on each product.

If the unit malfunctions, it must be returned to the factory for evaluation. OMEGA’s Customer Service Department will issue an
Authorized Return (AR) number immediately upon phone or written request. Upon examination by OMEGA, if the unit is found
to be defective, it will be repaired or replaced at no charge. OMEGA’s WARRANTY does not apply to defects resulting from
any action of the purchaser, including but not limited to mishandling, improper interfacing, operation outside of design limits,
improper repair, or unauthorized modification. This WARRANTY is VOID if the unit shows evidence of having been tampered with
or shows evidence of having been damaged as a result of excessive corrosion; or current, heat, moisture or vibration; improper
specification; misapplication; misuse or other operating conditions outside of OMEGA’s control. Components in which wear is not
warranted, include but are not limited to contact points, fuses, and triacs.

OMEGA is pleased to offer suggestions on the use of its various products. However, OMEGA neither assumes
responsibility for any omissions or errors nor assumes liability for any damages that result from the use of its
products in accordance with information provided by OMEGA, either verbal or written. OMEGA warrants only
that the parts manufactured by the company will be as specified and free of defects. OMEGA MAKES NO OTHER
WARRANTIES OR REPRESENTATIONS OF ANY KIND WHATSOEVER, EXPRESSED OR IMPLIED, EXCEPT THAT OF
TITLE, AND ALL IMPLIED WARRANTIES INCLUDING ANY WARRANTY OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE HEREBY DISCLAIMED. LIMITATION OF LIABILITY: The remedies of purchaser set forth
herein are exclusive, and the total liability of OMEGA with respect to this order, whether based on contract, warranty,
negligence, indemnification, strict liability or otherwise, shall not exceed the purchase price of the component upon
which liability is based. In no event shall OMEGA be liable for consequential, incidental or special damages.

CONDITIONS: Equipment sold by OMEGA is not intended to be used, nor shall it be used: (1) as a “Basic Component” under 10
CFR 21 (NRC), used in or with any nuclear installation or activity; or (2) in medical applications or used on humans. Should any
Product(s) be used in or with any nuclear installation or activity, medical application, used on humans, or misused in any way,
OMEGA assumes no responsibility as set forth in our basic WARRANTY / DISCLAIMER language, and, additionally, purchaser will
indemnify OMEGA and hold OMEGA harmless from any liability or damage whatsoever arising out of the use of the Product(s) in
such a manner.

For Other Locations Visit omega.com/worldwide

WARRANTY/DISCLAIMER

RETURN REQUESTS / INQUIRIES

Direct all warranty and repair requests/inquiries to the OMEGA Customer Service Department. BEFORE RETURNING ANY
PRODUCT(S) TO OMEGA, PURCHASER MUST OBTAIN AN AUTHORIZED RETURN (AR) NUMBER FROM OMEGA’S CUSTOMER
SERVICE DEPARTMENT (IN ORDER TO AVOID PROCESSING DELAYS). The assigned AR number should then be marked on the
outside of the return package and on any correspondence.

The purchaser is responsible for shipping charges, freight, insurance and proper packaging to prevent breakage in transit.

FOR WARRANTY RETURNS, please have the following
information available BEFORE contacting OMEGA:

1. Purchase Order number under which the product was
PURCHASED,

2. Model and serial number of the product under warranty, and

3. Repair instructions and/or specific problems relative to the
product.

OMEGA’s policy is to make running changes, not model changes, whenever an improvement is possible. This affords our customers the latest in technology and
engineering. OMEGA is a registered trademark of OMEGA ENGINEERING, INC.

© Copyright 2016 OMEGA ENGINEERING, INC. All rights reserved. This document may not be copied, photocopied, reproduced, translated, or reduced to any electronic
medium or machine-readable form, in whole or in part, without the prior written consent of OMEGA ENGINEERING, INC.

FOR NON-WARRANTY REPAIRS,
repair charges. Have the following information available BEFORE
contacting OMEGA:

1. Purchase Order number to cover the COST of the repair,

2. Model and serial number of the product, and

3. Repair instructions and/or specific problems relative to the
product.

consult OMEGA for current