Omega iDRN-PS-1000 User Manual

MADE

User’s Guide

www.omega.com

e-mail: [e-mail]

Shop on line at

iDRN-PS-1000

UNIVERSAL SWITCHING POWER SUPPLY

Compact DIN-Rail 24 Volt

IN

USA

®

®

L

N

+

-

Servicing North America:

USA:

One Omega Drive, P.O. Box 4047

ISO 9001 Certified

Stamford, CT 06907-0047
TEL: [phone] FAX: [phone]
e-mail: [e-mail]

Canada: 976 Bergar

Laval (Quebec) H7L 5A1
TEL: [phone] FAX: [phone]
e-mail: [e-mail]

For immediate technical or application assistance:

USA and Canada:

Sales Service: 1-800-826-6342 / 1-800-TC-OMEGA

®

Customer Service: 1-800-622-2378 / 1-800-622-BEST

®

Engineering Service: 1-800-872-9436 / 1-800-USA-WHEN

®

TELEX: 996404 EASYLINK: 62968934 CABLE: OMEGA

Mexico TEL: (001)800-TC-OMEGA

SM

FAX: [phone]

En Español: [phone]-7803 e-mail: [e-mail]

Servicing Europe:

Benelux:

Postbus 8034, 1180 LA Amstelveen, The Netherlands
TEL: [phone] FAX: [phone]
Toll Free in Benelux: 0800 0993344
e-mail: [e-mail]

Czech Republic: Rudé armády 1868, 733 01 Karviná 8

TEL: [phone] FAX: [phone]
e-mail: [e-mail]

France: 9, rue Denis Papin, 78190 Trappes

TEL: [phone] FAX: [phone]
Toll Free in France: 0800406342
e-mail: [e-mail]

Germany/Austria: Daimlerstrasse 26, D-75392 Deckenpfronn, Germany

TEL: [phone] FAX: [phone]
Toll Free in Germany: 0800 TC-OMEGA

SM

e-mail: [e-mail]

United Kingdom: One Omega Drive

ISO 9002 Certified River Bend Technology Centre

Northbank, Irlam
Manchester M44 5EX United Kingdom
TEL: [phone] FAX: [phone]
Toll Free in the UK: 0800 488 488
e-mail: [e-mail]

OMEGAnet

SM

On-Line Service Internet e-mail

http://www.omega.com [e-mail]

It is the policy of OMEGA to comply with all worldwide safety and EMC/EMI regulations that apply. OMEGA is constantly
pursuing certification of its products to the European New Approach Directives. OMEGA will add the CE mark to every
appropriate device upon certification.
The information contained in this document is believed to be correct but OMEGA Engineering, Inc. accepts no liability
for any errors it contains, and reserves the right to alter specifications without notice.
WARNING: These products are not designed for use in, and should not be used for, patient connected applications.

This device is marked with the international caution symbol. It is important to read the Setup Guide before installing or
commissioning this device as it contains important information relating to safety and EMC.

1. General Information and Features 2

2. Safety Considerations 3

3. Installation and Removal 4

3.1 Installation Clearance 5

3.2 Mounting on DIN Rail 6

3.3 Removal of Unit 7

4. Input and Output Connections 8

4.1 Block Diagram 8

4.2 Wiring for 115 Vac - Single Phase 9

4.3 Wiring for 230 Vac - Two Phase 10

5. Specifications 11
Input Power 11
Output Power 11
General 12
Wire Connections 12

6. Dimensions 13

7. Temperature Derating Graph 14

CONTENTS

1

The compact iDRN power supplies are designed to
supply well-regulated 24 volt DC power to sensors,
signal conditioners, data acquisition systems and
high level logic equipment.

Significant iDRN features include:

• Tested isolation, primary to output

• Recessed live parts and connector screws

• 35mm DIN rail mounting

• Wide input voltage tolerances

• Protective varistor input shunt

• Input AC spike rejection with LC filters

• LED power-on lamp

• Over-temperature protection

• Short circuit protection

• Low-ripple, well-regulated design

Features

GENERAL INFORMATION AND FEATURES

1

2

SAFETY CONSIDERATIONS

2

3

This device is marked with the international Caution symbol. It is
important to read this manual before installing or commissioning this
device as it contains important information relating to Safety and EMC
(Electromagnetic Compatibility).

Unpacking & Inspection

Unpack the instrument and inspect for obvious shipping damage. Do not attempt to
operate the unit if damage is found.

This instrument is a DIN rail mount device. Installation of this instrument should be done
by Qualified personnel. In order to ensure safe operation, the following instructions
should be followed.

This instrument has no power-on switch. An external switch or circuit-breaker shall be included in the
building installation as a disconnecting device. It shall be marked to indicate this function, and it shall
be in close proximity to the equipment within easy reach of the operator. The switch or circuit-breaker
shall not interrupt the Protective Conductor (Earth wire), and it shall meet the relevant requirements
of IEC 947–1 and IEC 947-3 (International Electrotechnical Commission). The switch shall not be
incorporated in the mains supply cord.

Furthermore, to provide protection against excessive energy being drawn from the mains supply in
case of a fault in the equipment, an overcurrent protection device shall be installed.

• The Protective Conductor must be connected for safety reasons. Check that the
power cable has the proper Earth wire, and it is properly connected. It is not safe to
operate this unit without the Protective Conductor Terminal connected.

• Do not exceed voltage rating on the label located on the top of the instrument
housing.

• Always disconnect power before changing signal and power connections.

• Do not use this instrument on a work bench without its case for safety reasons.

• Do not operate this instrument in flammable or explosive atmospheres.

• Do not expose this instrument to rain or moisture.

• Unit mounting should allow for adequate ventilation to ensure instrument does not
exceed operating temperature rating.

• Use electrical wires with adequate size to handle mechanical strain and power
requirements. Install without exposing bare wire outside the connector to minimize
electrical shock hazards.

EMC Considerations

• Whenever EMC is an issue, always use shielded cables.

• Never run signal and power wires in the same conduit.

• Use signal wire connections with twisted-pair cables.

• Install Ferrite Bead(s) on signal wires close to the instrument if EMC problems
persist.

If a rail assembly is to be transported, then
disconnection, dismounting and separate
packing of the power supply is
recommended.

For units that must be shipped installed on
the rail, additional bracing to resist
transportation shocks is recommended.

Do not attempt to install or connect to the
power supply when the mains are
energized.

Warning!

INSTALLATION AND REMOVAL

3

4

3.1 Installation Clearance

Ensure that there is enough room for mounting the power
supply unit. There should be a minimum of 1" [25mm] spacing
to allow sufficient air circulation for proper cooling.

Figure 3.1 — Mounting

INSTALLATION AND REMOVAL

3

5

1" [25mm] 1" [25mm]

AC POWER IN

SIGNAL INPUT

DC POWER IN

SIGNAL INPUT

DC POWER IN

DIN RAIL

SIGNAL
CONDITIONER
MODULES

24V-BUS

DC POWER OUT

SIGNAL INPUT

DC POWER IN

POWER SUPPLY

3.2 Mounting on DIN Rail

To install unit onto DIN Rail

1. Tilt unit, position mounting slot onto DIN Rail, as shown.

2. Push unit towards DIN Rail and it will snap into place.

Figure 3.2 — Mounting on 35mm DIN Rail

INSTALLATION AND REMOVAL

3

6

3

7

3.3 Removal of Unit

1. Insert flat screw-driver into tab and push downwards.

2. Unit will detach from DIN Rail.

Figure 3.3 — Removal of Unit

INSTALLATION AND REMOVAL

4

8

4.1 Block Diagram of Power Supply

Figure 4.1 — Block Diagram

4.2 Wiring

Warning: Do not turn on the ac power to the power supply

unit until you have completed all output connections. Failure
to do so may result in injury!

This device must only be installed electrically by a specially
trained electrician with corresponding qualifications.

Warning: To avoid potential electric shock use National
Electrical Code (NEC) safety practices when wiring and
connecting this unit to a power source.

INPUT AND OUTPUT CONNECTIONS

4

9

INPUT AND OUTPUT CONNECTIONS

4.2 Wiring (Continued)

115Vac - Single phase power wiring

Figure 4.2— Wiring for 115Vac - Single Phase

FUSE 1

Input Power

USE AWG 12-26 WIRE

L

N

USE A SWITCH TO APPLY

*

+24V POWER TO THE LOAD,
IF THE CAPACITANCE OF
THE LOAD WILL DRAW MORE
THAN 7 AMPS AT TURN ON.

+

-

Output Voltage

(for shielded wire
connections, if necessary)

Switch

*

Switch

Earth
Return
+24 V

LINE

NEUTRAL

Earth

To Signal

Conditioner

Modules

Earth

4.3 Wiring (Continued)

230Vac - Two phase power wiring

Figure 4.3— Wiring for 230Vac - Two Phase

INPUT AND OUTPUT CONNECTIONS

4

10

Input Power

USE AWG 12-26 WIRE

L

N

+

-

Output Voltage

(for shielded wire
connections, if necessary)

Switch

*

L1

Switch

FUSE 1

FUSE 2

USE A SWITCH TO APPLY

*

+24V POWER TO THE LOAD,
IF THE CAPACITANCE OF
THE LOAD WILL DRAW MORE
THAN 7 AMPS AT TURN ON.

Earth
Return
+24 V

L2

Earth

To Signal

Conditioner

Modules

Earth

SPECIFICATIONS

5

11

INPUT POWER

Input Voltage: 115 - 240Vac ±10%
Frequency: 50/60 Hz
Current: 0.400A @ 103Vac

0.190A @ 265Vac
Overvoltage Protection: 275 Volt Varistor
Overcurrent Protection: Fuse TR-5 800mA Time-lag / IEC 127-3
Input Wattage: 26 Watts

OUTPUT POWER

Output Voltage: 24Vdc ±2% @ 850mA (Resistive Load)
Output Wattage: 20 Watts*

* For higher output wattage greater than 20 watts follow the chart on
section 7, Figure 6.2.

Ripple: less than 100 mVrms
Operating Indicator: Front Panel LED

Short-Circuit/
Overload Protection: Current limiting with automatic short-

circuit protection and temperature
shutdown accomplished by the switcher.

Maximum number of
Signal Conditioner Depends on module used and
modules powered: configuration (6-10 modules)

SPECIFICATIONS

5

12

GENERAL

Operating Temperature: 23° to 122°F(-5° to 50°C)

Storage Temperature: -40° to 176°F(-40° to 80°C)

Mounting: 35mm DIN Rail

Size: Height: 3.55" (90mm)

Width: 0.99" (25mm)
Depth: 4.38" (111mm)

Weight: 0.3 lbs. (0.14 kg)

Equipment Type: CLASS I
Overvoltage: CAT II
Pollution Degree: 2

Insulation input to ouput: Dielectric strength to 2500V transient

based on EN61010 for 265Vrms
working voltage

WIRE CONNECTIONS

Screw down wire clamps, AWG 12 to 26 (ferrules recommended
for stranded wire).

DIMENSIONS

6

13

INPUT AC VOLTAGE / POWER OUTPUT

7

14

Example: If ambient is 50ºC, maximum wattage is 21W max. for
120-265Vac. If unit is operated at 21W at an input voltage of 100V,
the maximum ambient temperature allowed is 40ºC.

Figure 6.2 — Temperature Derating Graph

MAXIMUM POWER OUTPUT

INPUT AC
VOLTAGE

AMBIENT TEMPERATURE ºC

120V 265V

115V

110V

105V

100V

25ºC

-5ºC 30ºC

35ºC 40ºC 45ºC

50ºC

20W

24W

23W

22W

21W

AC INPUT CURRENT @ 100VAC INPUT

OUTPUT POWER AC CURRENT

20W 338mA
21W 355mA
22W 373mA
23W 392mA
24W 412mA

NOTES

15

NOTES

16

WARRANTY/DISCLAIMER

OMEGA ENGINEERING, INC. warrants this unit to be free of defects in materials and
workmanship for a period of 13 months from date of purchase. OM EGA Warranty adds an additional
one (1) month grace period to the normal one (1) year product warranty to cover handling and
shipping time. This ensures that OMEGA’s customers receive maximum coverage on each product.

If the unit should malfunction, it must be returned to the factory for evaluation. OMEGA’s Customer
Service Department will issue an Authorized Return (AR) number immediately upon phone or written
request. Upon examination by OMEGA, if the unit is found to be defective it will be repaired or replaced
at no charge. OMEGA’s WARRANTY does not apply to defects resulting from any action of the
purchaser, including but not limited to mishandling, improper interfacing, operation outside of design
limits, improper repair, or unauthorized modification. This WARRANTY is VOID if the unit shows
evidence of having been tampered with or shows evidence of being damaged as a result of excessive
corrosion; or current, heat, moisture or vibration; improper specification; misapplication; misuse or other
operating conditions outside of OMEGA’s control. Components which wear are not warranted, including
but not limited to contact points, fuses, and triacs.

OMEGA is pleased to offer suggestions on the use of its various products. However,
OMEGA neither assumes responsibility for any omissions or errors nor assumes liability
for any damages that result from the use of its products in accordance with information
provided by OMEGA, either verbal or written. OMEGA warrants only that the parts
manufactured by it will be as specified and free of defects. OMEGA MAKES NO OTHER
WARRANTIES OR REPRESENTATIONS OF ANY KIND WHATSOEVER, EXPRESSED OR
IMPLIED, EXCEPT THAT OF TITLE, AND ALL IMPLIED WARRANTIES INCLUDING ANY
WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
HEREBY DISCLAIMED. LIMITATION OF LIABILITY: The remedies of purchaser set forth
herein are exclusive and the total liability of OMEGA with respect to this order, whether
based on contract, warranty, negligence, indemnification, strict liability or otherwise,
shall not exceed the purchase price of the component upon which liability is based. In
no event shall OMEGA be liable for consequential, incidental or special damages.

CONDITIONS: Equipment sold by OMEGA is not intended to be used, nor shall it be used: (1) as a
“Basic Component” under 10 CFR 21 (NRC), used in or with any nuclear installation or activity; or (2) in
medical applications or used on humans. Should any Product(s) be used in or with any nuclear
installation or activity, medical application, used on humans, or misused in any way, OMEGA assumes
no responsibility as set forth in our basic WARRANTY /DISCLAIMER language, and additionally,
purchaser will indemnify OMEGA and hold OME GA harmless from any liability or damage whatsoever
arising out of the use of the Product(s) in such a manner.

RETURN REQUESTS / INQUIRIES

Direct all warranty and repair requests/inquiries to the OMEGA Customer Service Department.
BEFORE RETURNING ANY PRODUCT(S) TO OMEGA, PURCHASER MUST OBTAIN AN
AUTHORIZED RETURN (AR) NUMBER FROM OMEGA’S CUSTOMER SERVICE
DEPARTMENT (IN ORDER TO AVOID PROCESSING DELAYS). The assigned AR number
should then be marked on the outside of the return package and on any correspondence.

The purchaser is responsible for shipping charges, freight, insurance and proper packaging to
prevent breakage in transit.

FOR WARRANTY

RETURNS, please have
the following information available BEFORE
contacting OMEGA:

1. P.O. number under which the product

was PURCHASED,

2. Model and serial number of the product

under warranty, and

3. Repair instructions and/or specific

problems relative to the product.

FOR NON-WARRANTY REPAIRS,

consult
OMEGA for current repair charges. Have the
following information available BEFORE
contacting OMEGA:

1. P.O. number to cover the COST

of the repair,

2. Model and serial number of product, and

3. Repair instructions and/or specific

problems relative to the product.

OMEGA’s policy is to make running changes, not model changes, whenever an improvement is possible.
This affords our customers the latest in technology and engineering.

OMEGA is a registered trademark of OMEGA ENGINEERING, INC.
© Copyright 2002 OMEGA ENGINEERING, INC. All rights reserved. This document may not be copied,

photocopied, reproduced, translated, or reduced to any electronic medium or machine-readable form, in whole or in part,
without prior written consent of OMEGA ENGINEERING, INC.

MADE

PATENT NOTICE: This product is covered by one or more of the following patents: U.S. Pat. No. Des. 336,895;
5,274,577 / Canada 2052599; 2052600 / Italy 1249456; 1250938 / France Brevet No. 91 12756 / Spain 2039150;
2048066 / UK Patent No. GB2 249 837; GB2 248 954 / Germany DE 41 34398 C2
Used Under License. Other International Patents Pending.

IN

USA

M2540/0202

Where Do I Find Everything I Need for

Process Measurement and Control?

OMEGA…Of Course!

Shop on line at www.omega.com

TEMPERATURE



Thermocouple, RTD & Thermistor Probes, Connectors, Panels & Assemblies



Wire: Thermocouple, RTD & Thermistor



Calibrators & Ice Point References



Recorders, Controllers & Process Monitors



Infrared Pyrometers

PRESSURE, STRAIN AND FORCE



Transducers & Strain Gauges



Load Cells & Pressure Gauges



Displacement Transducers



Instrumentation & Accessories

FLOW/LEVEL



Rotameters, Gas Mass Flowmeters & Flow Computers



Air Velocity Indicators



Turbine/Paddlewheel Systems



Totalizers & Batch Controllers

pH/CONDUCTIVITY





pH Electrodes, Testers & Accessories



Benchtop/Laboratory Meters



Controllers, Calibrators, Simulators & Pumps



Industrial pH & Conductivity Equipment

DATA ACQUISITION





Data Acquisition & Engineering Software



Communications-Based Acquisition Systems



Plug-in Cards for Apple, IBM & Compatibles



Datalogging Systems



Recorders, Printers & Plotters

HEATERS





Heating Cable



Cartridge & Strip Heaters



Immersion & Band Heaters



Flexible Heaters



Laboratory Heaters

ENVIRONMENTAL
MONITORING AND CONTROL



Metering & Control Instrumentation



Refractometers



Pumps & Tubing



Air, Soil & Water Monitors



Industrial Water & Wastewater Treatment



pH, Conductivity & Dissolved Oxygen Instruments