Omega HH806AW User Manual

HH806AW

Internet e-mail

[e-mail]

WARNING

To avoid electrical shock, do not use this instrument

when working voltages at the measurement surface

over 24V AC or DC.

WARNING

To avoid damage or burns, do not make temperature

measurement in microwave ovens.

CAUTION

Repeated sharp flexing can break the thermocouple

leads. To prolong lead life, avoid sharp bends in the

leads, especially near the connector.

FEDERAL COMMUNICATIONS

COMMISSION

This device complies with Part 15 of the FCC Rules.
Operatio

n is subject to the following two condi-

tions:(1

) this device may not cause harmful interfer-

ence

, and (2) this device must accept any interference

received

, including interference that may cause unde-

sired operation.

NOTE

This equipment has been tested and found to comply
wit

h the limits for a Class B digital device, pursuant to

Par

t 15 of the FCC Rules. These limits are designed to

provid

e reasonable protection. This equipment gener-

ates

, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the in­structions

, may cause harmful interference to radio

communications

. However, there is no guarantee that

interferenc

e will not occur in a particular installation If

thi

s equipment does cause harmful interference to ra­dio or television reception, which can be determined
by turning the equipment off and on, the user is en­couraged to try to correct the interference by one or
more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and

receiver

.

- Connect the equipment into an outlet on a circuit dif-

ferent from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV tech-

nician for help.

Shielde

d interface cables must be used in order to

M4553/0907

Shop online at: omega.com e-mail: [e-mail]

For latest product manuals: omegamanual.info

INSTRUCTION

SHEET

1

2

MULTILOGGER THERMOMETER

OMEGAnet On-Line Service

omega.com

Servicing North America:

U.S.A: One Omega Drive, Box 4047

ISO 9001
Certified e-mail: [e-mail]

Canada: 976 Bergar

U.S.A Sales Service: 1-800-826-6342/1-800-TC-OMEGA
and Customer Service: 1-800-622-2378/1-800-622-BEST
Canada:

Mexico: En Espan ol: [phone]-7803

Benelux: Postbus 8034, 1180 LA Amstelveen, The Netherlands

Czech Frystatska 184, 733 01 Karviná, Czech Republic
Republic:

France:

Germany/ Daimlerstrasse 26, D-75392 Deckenpfronn, Germany
Austria:

United One Omega Drive, River Bend Technology Centre
Kingdom: Northbank, Irlam, Manchester
ISO 9002 M44 5BD United Kingdom
Certified Tel: [phone] FAX: [phone]

It is the policy of OMEGA Engineering, Inc. to comply with all
worldwide safety and EMC/EMI regulations that apply. OMEGA
is constantly pursuing certification of its products to the
European New Approach Directives. OMEGA will add the CE
mark to every appropriate device upon certification.
The information contained in this document is believed to be
correct, but OMEGA accepts no liability for any errors it
contains, and reserves the right to alter specifications without
notice.

should not be used for, human applications.

Stamford, CT 06907-0047
Tel: [phone] FAX: [phone]

Laval (Quebec) H7L 5A1, Canada
Tel: [phone] FAX: [phone]
e-mail: [e-mail]

For immediate technical or application assistance:

e-mail: [e-mail]
FAX: [phone] [e-mail]

Servicing Europe:

Tel: [phone] FAX: [phone]
Toll Free in Benelux: 0800 0993344
e-mail: [e-mail]

Tel: [phone] FAX: [phone]
Toll Free: 0800-1-66342 e-mail: [e-mail]

11, rue Jacques Cartier, 78280 Guyancourt, France
Tel: [phone] FAX: [phone]
Toll Free in France: 0800 466 342
e-mail: [e-mail]

Tel: + 49 (0)7056 9398-0 FAX: [phone]
Toll Free in Germany: 0800 639 7678
e-mail: [e-mail]

Toll Free in United Kingdom: 0800-488-488
e-mail: [e-mail]

These products are not designed for use in, and

®

®

INTRODUCTION

The instrument is a portable digital thermometer that

s external thermocouples of type K, J, R, S, T, E,

measure
N. The thermocouples types comply with the N.I.S.T. –

S 90 standard reference temperature/voltage tables.

IT

e thermometer features a dual thermocouple input, an

Th

e T/C offset and an USB interface for uploading

adjustabl
data to a PC using optional software and cable.

SAFETY INFORMATION

comply with emission limits.

s or modifications not expressly approved by

Change

e party responsible for compliance could void the

th
user‘s authority to operate the equipment.

WIRELESS NOTE

Wireless receiver must keep a distance of at least 30cm

from the meter and meter to meter distance must be at

least 20cm.

SPECIFICATIONS

ELECTRICAL

Measurement Range:

K-TYPE (0.1°) -200°C to 1372°C (-328°F to 2501°F)
J-TYPE (0.1°) -210°C to 1200°C ( -346°F to 2192°F)
T-TYPE (0.1°) -200°C to 400°C (-328°F to 752°F)
E-TYPE (0.1°) -210°C to 1000°C (-346°F to 1832°F)
R-TYPE (1°) 0°C to 1767°C (32°F to 3212°F)
S-TYPE (1°) 0°C to 1767°C ( 32°F to 3212°F)
N-TYPE (0.1°) -50°C to 1300°C ( -58°F to 2372°F)

*Based on the ITS-90 temperature standard.

According to temperature standard ITS-90.

Accuracy:

K/J/T/E-TYPE

±(0.05% rdg + 0.3°C) on -50°C to 1372°C
±(0.05% rdg + 0.7°C) on -50°C to -210°C
±(0.05% rdg + 0.6°F) on -58°F to 2501°F
±(0.05% rdg + 1.4°F) on -58°F to -346°F

N-TYPE

±(0.05% rdg + 0.8°C) on -50°C to 0°C
±(0.05% rdg + 0.4°C) on 0°C to 1300°C
±(0.05% rdg + 1.6°F) on -58°F to 32°F
±(0.05% rdg + 0.8°F) on 32°F to 2372°F

R/S-TYPE

±(0.05% rdg + 2°C) on 0°C to 1767°C
±(0.05% rdg + 4°F) on 32°F to 3212°F

Temperature Coefficient:

0.1 times the applicable accuracy specification per °C
from 0°C to 18°C and 28°C to 50°C (32°F to 64°F and
82°F to122°F).

Input Protection:

24V dc or 24V ac rms maximum input voltage on any
combination of input pins.

Reading Rate: 2.5 time per second.

Wireless Features:

Frequency range: 910~920MHz
Low current consumption less than 1mA

e transmitting distance can reach 25M without

Th
netic interference.

External Connections:

1. USB Port

2. DC power JACK(12V)

ENVIRONMENTAL

Ambient Operating Ranges:

Celsius or Fahrenheit user-selectable

0°C to 50°C (32°F to 122°F) <80% R.H.

Storage Temperature:

-20°C to 60°C (-4°F to 140°F) <70% R.H.

GENERAL

Display:

There are three display areas on the HH806 series LCD
(liquid crystal display). The Main and Second displays
are 4 _ digits with a maximum reading of 19999. These
are used for displaying the value of T1 or T2. The Third
display is for the date, time, or the differential value of
T1 to T2.

Overload: “----.-” or “OL” is display.
Battery: 1.5V x 4 PCS (SIZE AAA) UM-4 R03.
Battery Life: 120 hours typical with carbon zinc battery.
Dimensions: 160mm(H) x 83mm(W) x 38mm(D)

.

Weight: Approx. 365g including batteries.
Supplied Thermocouple:

1 meter (40”) type K insulated beaded wire thermocou­ple

. Maximum insulation temperature is 482°C (900°F).

Thermocoupl

e accuracy is ±1.1°C or 0.4% of reading

(whichever is greater) from 0°C to 1250°C.

1. OPERATIONAL MODE

There are three operation modes-Normal, Shift, and
Setup Mode.

NORMAL MODE:

Thi

s is the default mode, the operating functions for

th

e normal mode are printed on the top of each button

in white.

SHIFT MODE:

Th

e operating functions for the shift mode are printed
in gray on the buttons. While in the normal mode,
pres

s the SHIFT button to switch to shift mode. At the
lower-right corner of the display, the word “Shift” is
displaye

d to indicate shift mode. To switch back to

normal mode, press the SHIFT button again.

SETUP MODE:

Pres

s the set[ ] button in normal mode to switch to

setu

p mode, the indicator “SET” is shown on the left
sid

e of the display. To switch back to normal mode,

press SET[ ] button again.

WIRELESS MODE:

Pres

s the “ ” key for more than two seconds to start
wireles

s function. Press “

”

fo

r another two seconds

to stop wireless function. The wireless mode will shut
down if there is no wireless signal for two minutes.
SE

T CH/ID to 00,00 by pressing “T1-T2” key and

“ ” power key for more than six seconds when the
mete

r with the meter powered down. The second dis-

pla

y will show 00, which means that the channel and

ID has been set to 00.

To check the channel and ID of the meter:

Whe

n the meter is off press “ ” key and “ ” for

5 seconds. The LCD’s main display will show channel
number, the second display will show ID number.

2. NORMAL MODE

The following functions can only be used in the normal
mode.

(1) “ ” Power Button

The “ ” button turns the thermometer on or off.
Whe

n the meter is in MAX/MIN record mode, the

power off function is disabled.

(2) “[LIMITS]” Button (only Main display)

The limits function will alert the user when a meas­uremen

t exceeds a specified limit. To set the limit val-

ues

, refer to limits function in the setup mode. Press

th

e [LIMITS] button to activate the limits function; the
word “LIMIT” should be displayed on the LCD.
Whe

n the value of the main display exceeds the Hi

limit

, the word “Hi” will be displayed and the ther-

momete

r will beep in a pulsed tone. If the value of the

mai

n display is lower then the Lo limit, the word “Lo”

wil

l be displayed and the thermometer will beep in a

continuou

s tone To exit the limits function, press the

[LIMITS] button.

(3) “ ” Button

The backlight function is represented by this button
“

”. Pressing the button will turn on or off the LCD
backlight. The backlight will turn off automatically
after.

(4) “SAVE/READ” Button

The read data function works in conjunction with the
save function in the shift mode, it is used for reading

d data. The save function can be activated in shift

save

. Press the SAVE/READ button to read saved

mode

; the word “READ” should be displayed on the

data

. To navigate around the save data table, press the

LCD

y “SECOND” button until the “#” sign is dis-

overla

d on the second display. The location of the read

playe

r within the saved data table will be displayed.

pointe

e arrow buttons on the overlay are used for scrolling

Th

h the saved data. Press the smaller arrows “ ”

throug
or “ ” to step through the data one at a time. Press the

large

r arrows “ ” or “ ” to step through the data

n at a time. Pressing the overlay “ESC” button deac-

te
tivates the read data function.

(5) “LOG/READ” Button

The read log function works in conjunction with the log

. It is used for reading logged data. The log

function

n can be activated in the shift mode. Press the

functio
LOG/REA
th
overla
displa
play
ren
th
button
th
“ ” to step through the logged data or groups one at a

time
throug
th

D button to activate the log read function;

e word “READ” is displayed on the LCD. Press the

y SECOND button to rotate through following

y menus: T1, T2, GRP, and #. T1 and T2: Dis-

s the T1 or T2 saved data. GRP: Displays the cur-

t group number. #: Displays the current location of

e read pointer within a selected group. The arrow

s on the overlay are used for scrolling through

e data and groups. Press the smaller arrows “ ” or

. Press the larger arrows“” or “ ” to step

h the data or groups ten at a time. To navigate

e logg ed data and groups , press the overla y

SECON

D button until GRP appears in the second dis-

y panel. Then select the group using the arrows.

pla

s the SECOND button again until the “#” sign is

Pres
displayed
lected group will be displayed. Use the arrows to
scrol
button deactivates the read data function

. The location of the read pointer in the se-

l through the data. Pressing the overlay “ESC”

(7) HOLD Mode (only Main display)

When HOLD mode is selected, the thermometer holds

e present readings and stops all further measure-

th

. To activate the data hold mode, press the

ments

D button, and “HOLD” is displayed on the LCD.

HOL

g the HOLD button again cancels the function,

Pressin

d the instrument will automatically resume meas-

an
urements.

(8 ) M IN/M AX wit h time record Mode

(only Main display)

The MIN/MAX function records the highest and low-

t value recorded, and it calculates the average read-

es

, and the differences of MAX to MIN. Press

ing
MIN/MA
mode
or maximum measurement is recorded. Press the
MIN/MA
readings
MIN
Th
ment. AVG: The average values of the measurements.
Thi
tion
an
no
cordin
of MIN, MAX and AVG data, the MIN/MAX function
ca
th
automati
REL
also disabled.

X button to enter the MIN/MAX recording

. The beeper emits a tone when a new minimum

X button again to rotate through the current

: MAX: The highest measurement recorded.

: The lowest measurement recorded. MAX-MIN:

e difference of the highest and the lowest measure-

s mode works in conjunction with the hold func-

, pressing the HOLD button will stop the recording
d measurements (Previously recorded readings are
t erased). Press HOLD button again to resume re-

g and measurements. To prevent accidental loss

n only be cancelled by pressing and holding down

e MIN MAX key for more then 2 seconds. The

c power-off feature, and the power, °C/°F,

, SET, Hi/Lo Limits, TYPE, T1/T2 buttons are

(10) “T1/T2” Button (Main display)

The input selection button [T1/T2] selects the input for

e main display, T1 thermocouple or T2 thermocou-

th

. Press the T1/T2 button to switch between the two

ple

. When meter is turned on, it is set to the display

inputs
that was last in use.

(11) “T1/T2” Button (Second display)

The input selection button [T1/T2] selects the input for

e second display, T1 thermocouple or T2 thermo-

th

. Press the T1/T2 button to switch between the

couple

o inputs. When meter is turned on, it is set to the

tw
display that was last in use.

(12) “T1-T2/TIME” Button (Third display)

The input selection button [T1-T2] selects the system

e and date, or the differential between the two

tim
thermocouple
T1-T
mete
in use.

s (T1-T2) for the third display. Press the

2 button to switch the display options. When

r is turned on, it is set to the display that was last

3. SHIFT MODE

The following functions can only be used in the shift

mode.

(2) “°C/°F” Button

Press the °C/°F button to select the temperature

s can be displayed in Celsius (°C) or Fahre

reading

t (°F). When the thermometer is turned on, it

hei
to the temperature scale that was last in use.

(4) “SAVE” Button

The save function stores the T1, T2 data in a nonvola

e memory. Press the SAVE button to save the

til

t data, the word SAVE is displayed to indicate

ren

a has been saved. The built in memory can store

dat
to 256 data. The data can be read using the read
tion in the normal mode.

(5) “LOG” Button

The data log function continuously records the

g to a specified time interval. The time

accordin

l can be set using the interval setup function [INVT]

va
in the set up mode. Press the LOG button to activate

e log function; the indicators “LOG” and “MEM”

th

l be displayed on the LCD. There are 16 groups

wil

e used for storing the log data. A maximum

ar

0 data points can be saved in one log session.

16,00

s the LOG button again to exit the data log

Pres
tion.

(6) “CLR ?” Button

The CLR function clears all the saved and logged
in memory. When the CLR button is pressed, indicator

” is displayed and the “CLR” on upper-right

“MEM

D will blink. Pressing the “ENTER” button printed

LC
on the overlay in white will clear all saved and logged

. Press “ESC” button to exit this function without

data
clearing data.

(7) “REL” Button (Main display)

The relative value function can be used for comparing
a saved reference value with other measurements.

s the “REL” button to store the current measur

Pres

t as the reference value, and “REL” should be

men

d on the right part of the LCD. The next

playe

t will display the current value compared

uremen

e value. Press “REL” button again to clear

referenc

e value and deactivate the relative value

referenc
urement function.

(8) “APO” Button

Press the APO button to turn the “Auto power

n on or off. When this function is enabled,

functio

r “APO” is shown at the upper left part

indicato

. When APO (Auto power off) is enabled, it

LCD
automaticall
presse

e default time for APO is 5 minutes). Press power

(th
button to resume operation.

y turn the thermometer off no button

d for a period longer than the set time inte

(10) “TYPE” Button (Main display)

Press this button to change the type of thermocouple

e main display (K/J/T/E/R/S/N). If the inputs

th

n and second display are the same, then pressing

mai

s button will change the thermocouple type for

thi
displays.

(11) “TYPE” Button (Second display)

Press this button to change the type of thermocouple

the second display (K/J/T/E/R/S/N). If the inputs of

e main and second display are the same, then press-

th

g this button will change the thermocouple type for

in
both displays.

4. SETUP MODE

The following functions can only be use in the setup
mode.

(2)

Press the LIMITS button to enter the Hi/Lo limit setup
function. The words “LIMIT” and “Hi” will be flash
on the LCD along with the previous value for the Hi

. Enter the new Hi limit value using the number

limit

s printed in white on the overlay. The resolution of

key

o limit setup is 1 count . The “-“ button (same

Hi/L

n as the ESC) can be used to enter negative val-

butto
ues. Press the “ENTER” button to confirm the new

. You will then be prompted to enter a new Lo

limit

t value. Enter the new value and then press enter

limi
to finish setup of limits.

(3) “[INVT]” (Interval time setting)

To setup the time interval for the log function, press

e [INVT] button. The indicator “INV” will blink on

th

e top-right of the LCD and the previous interval is

th
displayed
on the overlay to change the time interval. Setting is
fro
(HH:MM:SS)
confirm. To exit this function, press the ESC button.

(8) “APO” Button (Auto power off time setting,

Use this function to change the time for the auto power
of
mode
wil
minutes
th
“ENTER
without changing the setting, press the ESC button.

MIN: 0001 minutes

(9) “[OFS]” Button (Thermocouple offset ad-

When the main display input is T1 and a thermocouple
is connected, the instrument can adjust the offset of the
thermocouple
th
to enter the thermocouple Offset Setup Function (OFS)
an
righ
Pres
overla
resolutio
se
ton to confirm. MAX: ±1999.9 °C/°F.

. Press the number buttons printed in white

m lef t t o r igh t o f t he fol low in g format

. Press the overlay “ENTER” button to

HH: interval Hour (0~23)
MM: interval Minute (0~59)
SS: interval Second (0~59)
MAX: 23:59:59
MIN: 00:00:01

min. 1 minute)

f (APO) function. Press the APO button in setup

, and the indicator “APO” and the current time

l flash on the LCD. The default time for APO is 5

. Press the number button printed in white on

e overlay to set the APO time. Press the overlay

” button to confirm. To exit this function

MAX: 19999 minutes

just)

. The same can be done for T2 when on

e main display. In the setup mode, press this button

d the indicator CAL should be displayed on the top-

t of the LCD and the current setting is also shown.

s the number buttons printed in white on the

y to change the offset of the thermocouple. The

n of the setup is 0.1°. Press the “-” button to

t a negative value. Press the overlay “ENTER” but-

(12) “[TIME]” Button (System time setting)

To set the system time, press the [TIME] button in the

p mode. The third display should show the current

setu

e and time with the year flashing. Enter the new

dat

e from left to right in the following format

valu
YY:MM:D
ton
dat

D and HH:MM:SS. Press the number but­s printed in white on the overlay to set the system
e and time. Press the “ENTER” button to confirm.

Exit this function by pressing ESC button.

WARNING

To avoid possible electrical shock, disconnect the

thermocouple connectors from the thermometer before

removing the cover

.

Battery Replacement

1. Power is supplied by 4pcs 1.5V (AAA SIZE) UM-4
R03.

2. The “ ” appears on the LCD display when replace-

t is needed. To replace battery remove screw from

men
back of meter and lift off the battery cover.

3. Remove the battery from battery contacts and replace.

4. When not in use for long periods remove battery.

5. Do not store in locations with high temperatures, or
high humidity.

Cleaning

Periodically wipe the case with a damp cloth and deter­gent, do not use abrasives or solvents.

*Software Operation manual is in the Software disk.

OMEGA ENG INEERING, INC. warrants this unit t o be free of defects in
material

s and workmanshi p for a peri od of from da te of pur­chase. OMEGA’ s WARRA NTY a dds an additiona l one (1) m onth grace
perio

d to the normal to cover handling and

shippin

g time. This ensures that OMEGA ’s custo mers recei ve maximum

coverage on each product.

If the unit malfunc tions, it mu st be retu rned to the factory for evaluation.

s Customer Service Departmen t wil l issu e an Author ized Return

OMEGA’
(AR

) number immediately upon phone or written request. Upon examination
by OMEGA, if the unit is found to be defective, it will be repaired or replaced
at no charge. OMEGA’s WARRANTY does not apply t o defects resulting
fro

m any action of the purch aser, including but no t limited to mishandling,

imprope

r interfacing, operation outside of design limits, improper repair, or

thorized modifi cation. T his WARR ANTY is V OID if t he unit shows

unau
evidenc

e of having been tampered w ith o r shows eviden ce of having been

d as a result of excess ive corrosion; o r current, heat , mois ture or

damage
vibra

tion; improper specification; misappl ication; misuse or othe r operating

s outsi de of OMEG A’s control. Compo nents which we ar i s not

condition
warranted, include but are not limited to contact points, fuses, and triacs.

CONDITIONS: Equipment sold by O MEGA is not intended to be used, nor
shal

l it be used: (1) as a “Basic Component” under 10 CFR 21 (NRC), used
in or with any nuclear ins tallation or activity; or (2) in medical applications or
use

d on humans. Sho uld any P roduct(s) b e used i n or wit h any nuclear

ins

tallation or activity, medical a pplication, u sed on humans, or misu sed in

an

y w ay, OMEGA assumes n o responsib ility as s et f orth in o ur basic

WARRANT

Y / DISCLA IMER l anguage , an d, addi tionally, pur chaser will

y OMEGA and hold OMEGA harmless from any liability or damage

indemnif
whatsoever arising out of the use of the Product(s) in such

Direct all w arranty and repair requests / inquiries to the OMEGA Customer

e Departme nt. BEFOR E RETURNIN G AN Y PRO DUCT (S) TO

Serv ic
OMEGA

, PURCH ASER MUS T OBTAIN AN AUTHORIZED RE TURN (AR)

R F ROM OM EGA’S CUSTOMER SERV ICE DE PARTMENT (IN

NUMBE
ORDER TO AVOID PR OCESSING DEL AYS). The assigned AR number
shoul

d the n be mar ked on t he outside of th e return package and o n any
correspondence.
The pur chaser is responsib le for sh ipping charges, f reight, insurance and
proper packaging to prevent breakage in transit.

FOR
please have the following
information available BEFORE
contacting OMEGA:

1. Purchase Order number under

which the product was
PURCHASED,

2. Model and serial number of the

product under warranty, and

3. Repair instructions and/or specific

problems relative to the product.

OMEGA’s policy is to make running changes, not model changes, whenever
an im provement i s possib le. This affords o ur cust omers t he latest in tech­nology and engineering.
OMEGA is
© Copyright 2007 OMEGA E NGINEERING, INC. All rights reserved. This
docume n
reduced to any electronic medium or machine -readable form, i n whole or in
part, without the prior written consent of OMEGA ENGINEERING, INC.

RETURNS,

a registered trademark of OMEGA ENGINEERING, INC.

t may no t be cop ied, pho tocopie d, repr oduced, tr anslate d, or

FOR
REPAIRS, consult OMEGA for
current repair charges. Have the
following information available
BEFORE contacting OMEGA:

1. Purchase Order number to cover
the COST of the repair,

2. Model and serial number of the
product, and

3. Repair instructions and/or specific
problems relative to the product.

a manner.

Where Do I Find Everything I Need for

Process Measurement

and Control?

OMEGA…Of Course!

Shop online at omega.com

TEMPERATURE

Thermocouple, RTD & Thermistor Probes,
Connectors, Panels & Assemblies
Wire: Thermocouple, RTD & Thermistor
Calibrators & Ice Point References
Recorders, Controllers & Process Monitors
Infrared Pyrometers

PRESSURE, STRAIN AND FORCE

Transducers & Strain Gages
Load Cells & Pressure Gages
Displacement Transducers
Instrumentation & Accessories

FLOW/LEVEL

Rotameters, Gas Mass Flowmeters & Flow
Computers
Air Velocity Indicators
Turbine/Paddlewheel Systems
Totalizers & Batch Controllers

pH/CONDUCTIVITY

pH Electrodes, Testers & Accessories
Benchtop/Laboratory Meters
Controllers, Calibrators, Simulators & Pumps
Industrial pH & Conductivity Equipment

DATA ACQUISITION

Data Acquisition & Engineering Software
Communications-Based Acquisition Systems
Plug-in Cards for Apple, IBM & Compatibles
Datalogging Systems
Recorders, Printers & Plotters

HEATERS

Heating Cable
Cartridge & Strip Heaters
Immersion & Band Heaters
Flexible Heaters
Laboratory Heaters

ENVIRONMENTAL
MONITORING AND CONTROL

Metering & Control Instrumentation
Refractometers
Pumps & Tubing
Air, Soil & Water Monitors
Industrial Water & Wastewater Treatment
pH, Conductivity & Dissolved Oxygen
Instruments

Made in Taiwan