Omega FPD20X1, FPD20X2, FPD20X3, FPD20X4, FPD20X5 Specification

Page 1

POSITIVE DISPLACEMENT FLOW METERS

FPD2000 Series

U ±0.5% Rdg Accuracy U Aluminum, 303 or 316 SS Bodies U Pressure Rating Up to 345 bar (5000 psi) U Pulse or mA Outputs Available U Bi-Directional Flow Capabilities U Economical Cost

The FPD2000 Series represents a positive displacement meter that is affordable and accurate. One primary feature is the ability to maintain consistent accuracy despite changing viscosity conditions. This reliability, coupled with a large turndown range, offers an affordable replacement for older turbine technology. The meter’s solid construction and excellent dynamic response are well suited to the measurement of oil, grease, fuel, solvents, polyurethanes, brake ﬂuid, skydrol as well as other nonabrasive lubricating ﬂuids. Since there is no need for straight run piping upstream or downstream of the ﬂowmeter, the FPD2000 ﬂow meters are simple to use and to install. The meters produce good resolution and high accuracy at low ﬂow rates. Flow may be bi-directional, such as for cylinder position measurements, without damage to internal parts.

FPD2004-A shown smaller than actual size.

SPECIFICATIONS

Accuracy: ±0.5% over 10:1 turndown with 30cP ﬂuid Repeatability: ±0.1% Max Fluid Temperature:

Aluminum Body: Meter 85°C (185°F) Stainless Body: Meter 204°C (400°F) Pressure Maximum: 345 bar (5000 psi) Wetted Materials

Body:

FPD2000 Series: Aluminum

FPD2010 Series: 303 SS FPD2020 Series: 316 SS

Gear: Stainless steel O-Ring: PTFE, FKM (optional) Bearings: Stainless steel

Outputs

Temperature Range (Electronics): Standard Aluminum

and SS versions -40 to 85°C (-40 to 185°F)

Model No. Pulses/Liter (Pulses/Gallon) Body Dia cm (inch) FPD20X1 FPD20X2 FPD20X3 FPD20X4 FPD20X5

On analog output models (FPD2XXX-A) add 12 cm (4.8") to the body height to obtain overall height.

14,000 (53,000) 7.6 (3) 8.6 (3.4) 30

4200 (15,900) 8.4 (3.3) 8.6 (3.4) 30

1700 (6600) 8.4 (3.3) 8.6 (3.4) 30

470 (1800) 12.4 (4.9) 13.8 (5.45) 30 420 (1600) 21.3 (8.4) 17 (6.7) 200

Square Wave: (Basic unit) Supply Voltage: +10 to 28 Vdc Supply Current: 8 mA @ 12 Vdc,12 mA @ 24 Vdc Duty Signal: 50% ±15% Minimum Signal: 0.5 Hz Frequency: Flow dependent, up to 2000 Hz Driving Capacity: 50 mA max resistive load Output Impedance: 40 Ω - analog switch and

self-resetting fuse

Analog Output (-A Models)

Supply Voltage: 10 to 30 Vdc Output: 4 to 20 mA Input: 0.25 Hz to 5 kHz Amplitude: 1 to 40 Vp-p Update Time: 1/F + 25 msec Linearity: ±0.01% rdg

*Body Height

cm (inch)

Filtration

(microns)

F-75

Page 2

FPD2005 shown smaller than actual size.

To Order

Model No. NPT Range LPM (GPM) Description

FPD2001

FPD2002

FPD2003

FPD2004

FPD2005

FPD2001-A

FPD2002-A

FPD2003-A

FPD2004-A

FPD2005-A

FPD2011

FPD2012

FPD2013

FPD2014

FPD2015

FPD2011-A

FPD2012-A

FPD2013-A

FPD2014-A

FPD2015-A

FPD2021

FPD2022

FPD2023

FPD2024

FPD2021-A

FPD2022-A

FPD2023-A

FPD2024-A

⁄4 0.01 to 3 (0.003 to 0.8) Aluminum gear meter with pulse output

⁄4 0.04 to 7.5 (0.01 to 2) Aluminum gear meter with pulse output

⁄2 0.11 to 26.4 (0.03 to 7) Aluminum gear meter with pulse output

⁄4 0.19 to 75 (0.05 to 20) Aluminum gear meter with pulse output

⁄4 1.9 to 227 (0.5 to 60) Aluminum gear meter with pulse output

⁄4 0.01 to 3 (0.003 to 0.8) Aluminum gear meter with 4 to 20 mA output

⁄4 0.04 to 7.5 (0.01 to 2) Aluminum gear meter with 4 to 20 mA output

⁄2 0.11 to 26.4 (0.03 to 7) Aluminum gear meter with 4 to 20 mA output

⁄4 0.19 to 75 (0.05 to 20) Aluminum gear meter with 4 to 20 mA output

⁄4 1.9 to 227 (0.5 to 60) Aluminum gear meter with 4 to 20 mA output

⁄4 0.01 to 3 (0.003 to 0.8) 303 SS gear meter with pulse output

⁄4 0.04 to 7.5 (0.01 to 2) 303 SS gear meter with pulse output

⁄2 0.11 to 26.4 (0.03 to 7) 303 SS gear meter with pulse output

⁄4 0.19 to 75 (0.05 to 20) 303 SS gear meter with pulse output

⁄4 1.9 to 227 (0.5 to 60) 303 SS gear meter with pulse output

⁄4 0.01 to 3 (0.003 to 0.8) 303 SS gear meter with 4 to 20 mA output

⁄4 0.04 to 7.5 (0.01 to 2) 303 SS gear meter with 4 to 20 mA output

⁄2 0.11 to 26.4 (0.03 to 7) 303 SS gear meter with 4 to 20 mA output

⁄4 0.19 to 75 (0.05 to 20) 303 SS gear meter with 4 to 20 mA output

⁄4 1.9 to 227 (0.5 to 60) 303 SS gear meter with 4 to 20 mA output

⁄4 0.01 to 3 (0.003 to 0.8) 316 SS gear meter with pulse output

⁄4 0.04 to 7.5 (0.01 to 2) 316 SS gear meter with pulse output

⁄2 0.11 to 26.4 (0.03 to 7) 316 SS gear meter with pulse output

⁄4 0.19 to 75 (0.05 to 20) 316 SS gear meter with pulse output

⁄4 0.01 to 3 (0.003 to 0.8) 316 SS gear meter with 4 to 20 mA output

⁄4 0.04 to 7.5 (0.01 to 2) 316 SS gear meter with 4 to 20 mA output

⁄2 0.11 to 26.4 (0.03 to 7) 316 SS gear meter with 4 to 20 mA output

⁄4 0.19 to 75 (0.05 to 20) 316 SS gear meter with 4 to 20 mA output

DPF701 shown smaller than actual size.

Accessories

Model No. Description DPF701 FPD2000-CONNECTOR FPD2000A-CONNECTOR

Comes complete with operator’s manual, K-factor certiﬁcate, and connector. Certiﬁcate does not include points and is not a NIST certiﬁcate. FPD2000, pulse output models, come with the 6-pin FPD2000-CONNECTOR.

FPD2000-A, 4 to 20 mA output models, come with the FPD2000A-CONNECTOR. For High Temperature option on stainless steel models, add sufﬁx “-HT” to model number, for additional cost. Ordering Examples: FPD2003, aluminum gear meter with pulse output,

⁄

DIN panel meter with red LED display.

FPD2012-A, 303 SS gear meter with 4 to 20 mA output,

Pulse input 6-digit panel meter for rate or total Replacement 6-pin connector for the FPD2000 pulse output models Replacement 3-pin connector for the FPD2000-A 4 to 20 mA output models

⁄

NPT connections, 0.03 to 7 GPM range and DPF701 digital

NPT, 0.01 to 2 GPM range.

⁄

F-76