Omega DP25B-S, DP25B-E Quick Start Quide

DP25B-S

Strain Meter

MQS3598/0317

5 6

Scaling Without Known Loads (Continued)

3. Press /TARE again. The unit displays the

last setting for IN!1 .
(The first digit flashes.)

4. Change IN!1 as necessary:

•

Press /NT/GRS to set or change the digit's current value. Continue
to press



/NT/GRS until the meter displays the

desired value for the

flashing digit. Values can range from 0 to 9.

For the first digit, you can

also enter a minus sign (–) or –1.

• Press /TARE to scroll to the digit(s) you want to change.

5. Press MENU to store IN!1. The unit displays:

6. Press /TARE. The unit displays the last

setting for RD!1 . (The first digit flashes.)

7. Change RD!1 as necessary:

• Press /NT/GRS until the meter displays the desired value for
the flashing digit. Values can range from 0 to 9. For the first digit,
you can also enter a minus sign (–) or –1.

• Press



/TARE to scroll to the digit(s) you want to change.

8. Press MENU to store the value shown for RD!1 .

The unit displays:

To define the maximum load (IN!2 and RD!2

):

1. Repeat steps 3–8 above, entering the values for IN!2

and RD!2 .

2. Once you've completed all steps, the unit displays:

To begin operation:

Reinitialize the unit (press RESET twice or
press MENU until RST flashes on the
display). When a numeric reading appears,
the unit is operational.

Determining Reading Offset

The run mode reading for meters scaled without known loads may
reflect an offset. For example, say you set

RD!1

to 0 and

RD!2

to
100, but when the minimum load is applied, a negative value of –1.5
displays on the front panel.

To correct the reading offset:

1. With zero load applied, note the reading on the display.

2. Subtract that amount from the RD!1 and RD!2 values you origi-

nally entered.
In the example, the offset would be –1.5. If RD!1 is to read 0 in

Run Mode, it must be reentered as 1.5. RD!2 must likewise be
reentered as 101.5 if the meter is to read 100 when the maxi­mum load is applied.

3.

Repeat the steps for "Scaling Without Known Loads," but when
the values for IN!1 and IN!2 display, do not change them.
Instead, press MENU to move to the prompts for RD!1 and RD!2
and make the necessary changes.

4. Reinitialize the unit and resume operation.

Scaling With Known Loads

(Continued)

6. Press MENU to store IN!1. The unit displays:

7. Press /TARE. The unit displays the last setting for RD!1.

8. Change RD!1 as necessary:

• Press /TARE to scroll to the digit(s) you want to change
(it flashes on the display).

• Press



/NT/GRS to change the value of the flashing digit.

Values can range from 0 to 9. For the first digit, you can also
enter a minus sign (–) or –1.

9. Press MENU to store the value shown for RD!1 .

The unit displays:

To identify the maximum known load (IN!2 and RD!2

):

1. Apply the maximum known load (100%).

2. Repeat steps 4–9 above, for IN!2 and RD!2 .

Once you've completed all steps, the unit displays:

To begin operation:

Reinitialize the unit (press RESET twice or
press MENU until RST flashes on the display).
When a numeric reading appears, the unit is
operational.

Scaling Without Known Loads

For 0–100 mV sensors, the values for the minimum and maximum
input loads are always as follows:

• Minimum load (IN!1)— 0

• Maximum load (IN!2)— 9999.

If your installation uses a different sensor type, you must calculate
the values for IN!1 and IN!2 before proceeding with the steps
below. Use the formula provided in the Operator's Manual.
To define the minimum load

(

IN!1 and RD!1

):

1. If it's not already shown, press MENU until

the unit displays:

2. Press /TARE. The unit displays:

WARRANTY/DISCLAIMER

OMEGA ENGINEERING, INC. warrants this unit to be free of defects in materials and
workmanship for a period of one (1) year from the date of purchase. In addition to OMEGA’s
standard warranty period, OMEGA Engineering will extend the warranty period for four (4)
additional years if the warranty card enclosed with each instrument is returned to OMEGA.

If the unit malfunctions, it must be returned to the factory for evaluation. OMEGA’s Customer
Service Department will issue an Authorized Return (AR) number immediately upon phone or
written request. Upon examination by OMEGA, if the unit is found to be defective, it will be
repaired or replaced at no charge. OMEGA’s WARRANTY does not apply to defects resulting
from any action of the purchaser, including but not limited to mishandling, improper interfacing,
operation outside of design limits, improper repair, or unauthorized modification. This
WARRANTY is VOID if the unit shows evidence of having been tampered with or shows
evidence of having been damaged as a result of excessive corrosion; or current, heat, moisture
or vibration; improper specification; misapplication; misuse or other operating conditions outside
of OMEGA’s control. Components which wear are not warranted, including but not limited to
contact points, fuses, and triacs.

OMEGA is pleased to offer suggestions on the use of its various products. However,
OMEGA neither assumes responsibility for any omissions or errors nor assumes liability
for any damages that result from the use of its products in accordance with information
provided by OMEGA, either verbal or written. OMEGA warrants only that the parts
manufactured by it will be as specified and free of defects. OMEGA MAKES NO OTHER
WARRANTIES OR REPRESENTATIONS OF ANY KIND WHATSOEVER, EXPRESS OR
IMPLIED, EXCEPT THAT OF TITLE, AND ALL IMPLIED WARRANTIES INCLUDING ANY
WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
HEREBY DISCLAIMED. LIMITATION OF LIABILITY: The remedies of purchaser set forth
herein are exclusive, and the total liability of OMEGA with respect to this order, whether
based on contract, warranty, negligence, indemnification, strict liability or otherwise, shall
not exceed the purchase price of the component upon which liability is based. In no event
shall OMEGA be liable for consequential, incidental or special damages.

CONDITIONS: Equipment sold by OMEGA is not intended to be used, nor shall it be used: (1)
as a “Basic Component” under 10 CFR 21 (NRC), used in or with any nuclear installation or
activity; or (2) in medical applications or used on humans. Should any Product(s) be used in or
with any nuclear installation or activity, medical application, used on humans, or misused in any
way, OMEGA assumes no responsibility as set forth in our basic WARRANTY/DISCLAIMER
language, and, additionally, purchaser will indemnify OMEGA and hold OMEGA harmless from
any liability or damage whatsoever arising out of the use of the Product(s) in such a manner.

RETURN REQUESTS/INQUIRIES

Direct all warranty and repair requests/inquiries to the OMEGA Customer Service Department.
BEFORE RETURNING ANY PRODUCT(S) TO OMEGA, PURCHASER MUST OBTAIN AN
AUTHORIZED RETURN (AR) NUMBER FROM OMEGA’S CUSTOMER SERVICE
DEPARTMENT (IN ORDER TO AVOID PROCESSING DELAYS). The assigned AR number
should then be marked on the outside of the return package and on any correspondence.

The purchaser is responsible for shipping charges, freight, insurance and proper packaging to
prevent breakage in transit.

FOR W

ARRANTY RETURNS, please have
the following information available BEFORE
contacting OMEGA:

1. Purchase Order number under which the

product was PURCHASED,

2. Model and serial number of the product

under warranty, and

3. Repair instructions and/or specific

problems relative to the product.

FOR NON-W

ARRANTY REPAIRS, consult
OMEGA for current repair charges. Have the
following information available BEFORE
contacting OMEGA:

1. Purchase Order number to cover the

COST of the repair,

2. Model and serial number of product, and

3. Repair instructions and/or specific

problems relative to the product.

OMEGA’s policy is to make running changes, not model changes, whenever an improvement is
possible. This affords our customers the latest in technology and engineering.

OMEGA is a registered trademark of OMEGA ENGINEERING, INC.

© Copyright 2017 OMEGA ENGINEERING, INC. All rights reserved. This document may not be
copied, photocopied, reproduced, translated, or reduced to any electronic medium or machine­readable form, in whole or in part, without the prior written consent of OMEGA ENGINEERING,
INC.

PATENT AND TRADEMARK NOTICE: The “Meter Case Bezel Design” is a trademark of
NEWPORT Electronics, Inc., registered in the U.S. USED UNDER LICENSE. This product is
covered by one or more of the following patents: U.S. Pat. No. Des. 336,895; 5,274,577;
6,243,021 / CANADA 2052599; 2052600 / ITALY 1249456; 1250938 / GERMANY DE 41 34398
C2 / SPAIN 2039150; 2048066 / UK Patent No. GB2 249 837; GB2 248 954 / FRANCE BREVET
NO. 91 12756. Other U.S. and International Patents pending or applied for.

This device is marked with the international caution symbol. It is important to read the
Setup Guide before installing or commissioning this device, as the guide contains
important information relating to safety and EMC.

WARNING: These products are not designed for use in, and should not be used for, patient­connected applications.

It is the policy of OMEGA to comply with all worldwide safety and EMC/EMI regulations that apply.
OMEGA is constantly pursuing certification of its products to the European New Approach Directives.
OMEGA will add the CE mark to every appropriate device upon certification.

The information contained in this document is believed to be correct, but OMEGA Engineering, Inc.
accepts no liability for any errors it contains, and reserves the right to alter specifications without
notice.

TRADEMARK NOTICE:

®

,

omega.com

®

,and , are Trademarks of

OMEGA ENGINEERING, INC.

®

U.S.A.:

Servicing North America:

Omega Engineering, Inc.
Toll-Free: 1-800-826-6342 (USA & Canada only) Customer
Service: 1-800-622-2378 (USA & Canada only) Engineering
Service: 1-800-872-9436 (USA & Canada only)

Fax: [phone] Tel: [phone]

e-mail: [e-mail]

For Other Locations Visit www.omega.com/worldwide

omega.com [e-mail]

Using This Quick Star t Manual

Use this Quick Start Manual to set up your Strain Meter and begin operation.
Information is provided on how to:

• Connect ac power • Set basic options for operation
Connect the sensor • Scale the meter.

Features with are for the “B” version which has three-color
programmable “Big” LED display - All segment characters shown are for
the “B” version.

IMPORTANT: For complete information on all setup options, please
refer to the Operator’s Manual.

This Quick Start Manual includes specific configuration param­eters for bridge sensors with an output range of 0–100 mV and
10 V excitation. Other sensor types may require different
parameters or additional ones. When this is the case, we refer
you to the Operator's Manual for detailed instructions.

Safety Consideration

This device is marked with the international Caution symbol.

The instrument is a panel mount device protected in accordance with
2014/35/EU, electrical safety requirements for electrical equipment for
measurement, control and laboratory. Remember that the unit has no
power-on switch. Building installation should include a switch or circuit­breaker that must be compliant to IEC 947-1 and 947-3.

SAFETY:

• Do not exceed voltage rating on the label located on the top of the instrument
housing.

• Always disconnect power before changing signal and power connections.

• Do not use this instrument on a work bench without its case for safety
reasons.

• Do not operate this instrument in flammable or explosive atmospheres.

• Do not expose this instrument to rain or moisture.

EMC:

• Whenever EMC is an issue, always use shielded cables.

• Never run signal and power wires in the same conduit.

• Use signal wire connections with twisted-pair cables.

• Install Ferrite Bead(s) on signal wire close to the instrument if EMC problems
persist.

Mount the Unit

1. Cut a panel opening using the dimen­sions shown to the right.

2. Position the unit in the opening, making
sure the front bezel is flush with the
panel.

3. Install retaining clips on both sides of
the meter and tighten against the panel.

Wiring

Warning: Do not connect AC power to your device until you
have completed all input and output connections. This device
must only be installed by a specially trained electrician with
corresponding qualifications. Failure to follow all instructions
and warnings may result in injury!

1. Remove the panel at the back of the unit.

2. Locate the TB1 connector.

3. Insert the correct wire in each terminal as shown in the following figure
and tighten the lockdown screws.

4. Tug gently on the wires to verify the connections.

External Fuse Required:

Time-delay, UL 248-14 listed Time-lag, IEC 127-3 recognized

175 mA (115 Vac line) 125 mA (115 Vac line)
80 mA (230 Vac line) 63 mA (230 Vac line)

AC Powered Unit Connections

START HERE

Wiring (continued)

When using DC power, do not use internal excitation or Isolated
Analog Output for high color brightness. For low or medium
brightness, internal excitation is limited to 24 V @ 25 mA; 5 V, 10
V, 12 V @ 35 mA.
In order to maintain the same degree of protection as the AC units,
always use a Safety Agency Approval DC source with the same
Overvoltage Category and Pollution Degree.

DC Powered Unit Connections

Connect the Sensor

1. Locate the TB2 connector on the rear of the unit.

2. Attach the sensor wires and tighten the lockdown screws.
The diagram below shows the wiring for bridge sensors with internal
excitation.

Refer to the Operator’s Manual for setup requirements for other
sensor types.

Bridge Sensor with Internal Excitation

3. Tug gently on the wires to verify the connections.

4. Replace the panel at the back of the unit.

Using the Configuration Menu

To configure the meter, you use the buttons on the front panel.

To: Take This Action:

Display the Press the MENU button. The first function
Configuration Menu on the menu, INPT, displays.
Select a submenu 1. Press MENU until the function you
function want is shown.

2. Press /TARE.

The information you can change flashes.

Select a value 1. Press /NT/GRS to display the option
for that submenu you want.

function 2. Press MENU to store it.

STRD quickly flashes, indicating that
the selection has been stored in memory.
Then the next menu function displays.

Go back to previous Press RESET once.
menu function

Exit the Press RESET twice. The unit displays
Configuration RST as it reinitializes. When a numeric
Menu value displays, the unit is in run mode.

(Optionally, you can press MENU to
move through all the menu functions
until the unit reinitializes.)

2 3 4

To Set the Decimal Point (continued)

3.

Press /NT/GRS to move the decimal point to
the desired location. The factory settings is
FFFF. The other choices are F.FFF, FF.FF,
and FFF.F.

4. Press MENU to select the decimal point position shown. The

unit displays:

To Scale the Meter

You can scale the meter in one of two ways:

1. With a known load — This method uses input (load) information
sent from another device such as a scale or a simulator for
voltage or current.

2. Without a known load — This involves calculating the load
based on transducer specifications and manually entering it to
the meter.

For both methods, you must first identify the minimum input load
IN!1 and the corresponding display reading you want RD!1. Then
you identify the maximum input load IN!2 and its corresponding
display reading RD!2 .

The decimal point is for display purposes only — you set it
where you want it to display for your application.

When entering IN!1 and IN!2 values, ignore any decimal
point on the display. However, you must enter RD!1 and
RD!2 values with the decimal point in the desired position.

Scaling With Known Loads

To identify the minimum known load (IN!1 and RD!1

):

1. If it's not already shown, press MENU until the unit displays:

2. Apply the minimum known load (0%).

3. Press /TARE. The unit displays:

4. Press /TARE again. The unit displays the last setting for

IN!1

.

5. Press /TARE again. The unit displays the actual reading
being received from the sending device.

MENU SUBMENU /TARE DESCRIPTION

INPT 100M, ±50M, !1 0 V , !±5 V , 0-20*Input
DEC.P FFFF*, F.FFF, FF.FF, FFF.F Decimal Point
RD.S.O IN!1, RD!1, IN!2 , RD!2 Scale and Offset
RD.CF R.1=T*, R.1=N

Reading Configuration

R.2=0, R.2=1, R.2=2 , R.2=3, R.2=4

*

R.3=F*, R.3=U

R.4=P, R.4=G
COLR GRN, RED, AMBR Display Color
S1.CF S.1=A*, S.1=B

Setpoint 1 Configuration

S.2=U*, S.2=L

S.3=N*, S.3=G

shown if R.4=G

S2.CF S.1=A*, S.1=B

Setpoint 2 Configuration

S.2=U*, S.2=L

S.3=N*, S.3=G

shown if R.4=G

S1.DB 0003

*

Setpoint 1, Deadband

S2.DB 0003

*

Setpoint 2, Deadband

OT.CF O.1=E*, 0.1=D Analog Output

O.2=C*, 0.2=V

Configuration

O.3=A*, 0.3=P
OT.S.O RD!1, OUT1, RD!2, OUT2

Output Scale & Offset

LK.CF RS=E*, RS=D

Lockout Configuration

SP=E*, SP=D

L3=0*, L3=1
BRIT M.BrT, .BrT, H.BrT

Display Brightness

* Factory Default Settings

To Set the Input Type

1. Press MENU until the unit displays:

2. Press /TARE. The unit displays:

3. For this application you want 100M. If 100M is not displayed,
press /NT/GRS until it appears. Other choices are 50M, 10V,
5V and 0-20.

Refer to the Operator's Manual for more information on
changing ranges.

4. Press MENU to select the sensor shown. The meter displays the
next menu item. If you changed input type, the meter displays:

To Set the Decimal Point

1. If it's not already shown, press MENU until the
unit displays:

2. Press /TARE. The unit displays:

Using the Configuration Menu (continued)