Page 1
BS6050/6051
RTD Input Benchtop Meters
INSTRUCTION
SHEET
Shop online at omega.comSM e-mail: [email protected]
For latest product manuals: www.omegamanual.info
Unpacking Instructions
Remove the Packing List and verify that you have
received all equipment, including the following:
• BS6050 or BS6051 Meter
• Mating Connector
• Power Cord
If you have any questions about the shipment, please call
the Customer Service Department at 1-800-622-2378 or
203-359-1660.
When you receive the shipment, inspect the container
and equipment for signs of damage. Note any evidence
of rough handing in transit. Immediately report any
damage to the shipping agent.
The carrier will not honor damage claims unless all shipping
material is saved for inspection. After examining and
removing contents, save packing material and carton in the
event reshipment is necessary.
Introduction
The BS6050/6051 thermometers are highly accuracy
microprocessor-driven thermometers for use with PT100
Sensors. PT100 calibrations are based upon NBS and
BS tables. The units are housed within tough ABS cases
complete with tilt feet for ease of viewing.
Features
• BS6000: Single RTD input
• BS6051: 6 RTD inputs, switch selectable
• Resolution 0.1° to 999.9°
• °C/°F switchable
• LCD backlit display
• Overrange/faulty probe indication
M2067/0915
NOTE:
Installation
Mechanical
The units may be used either at or at an angle,
depending upon the desired viewing angle. The tilt
feet are located on the underside of the instrument,
and should be pulled down and toward the front of the
instrument until the stop is reached.
Electrical
The units are supplied with a power plug. It is important
to be sure that the appropriate input supply voltages are
used.
Sensor Connections
The thermocouples are connected via miniature
thermocouple plugs on the front of the unit. On
the BS6001, the switch must be positioned to the
corresponding thermocouple socket. Refer to the wiring
diagram on the unit.
Selecting Temperature Scale
The choice of temperature scale (°C/°F) is made using the
slideswitch on the real panel, observing the table shown
above the switch. There is no need to reset the unit as
it continually monitors the switch settings and will
automatically recongured itself.
Open Circuit Sensor Detection
An error in the probe is shown by a series of bars (----) on
the display. Under these conditions, either the probe has
an error or the temperature you are measuring is out of
range.
Page 2
BS6050/6051 RTD Input Benchtop Meters
SPECIFICATIONS
Environmental
Ambient Operation Range:
Storage Temperature Range: -40 to 50°C (-40 to 122°F)
Humidity: 0 to 70% R. H.
General
Weight:
BS6050: 500 grams
BS6051: 850 grams
Dimensions: BS6050: 118 x 57 x 150 mm
(4.65 x 2.24 x 5.90")
BS6051: 148 x 67 x 190 mm
(5.83 x 2.64 x 7.48")
Connections: Miniature T/C Connectors
Electrical
Accuracy @ 23°C:
±0.25% reading ±0.2°C
Characterizing Errors: Less than 0.05°C
Temperature Coefcient: 0.01% of reading/°C
Cold Junction Compensation: 0.0075°C/°C
Resolution: 0.1 to 999.9
1° above 1000°
Input Voltage Ranges: 110 Vac ±10%
240 Vac ±10% optional
9-30 Vac or DC optional
0 to 50°C (32 to 122°F)
Measurement Ranges
Celsius Fahrenheit
-200 to 850 -200 to 1562
Notes:
1. Strong RF elds may adversely affect measurement accuracy.
2. To avoid earth ground problems, it is recommended that
wherever possible, insulated sensors be used.
3. If non-insulated sensors are used, care must be taken to minimize
the common mode voltage between the sensor input and the
power supply to the instrument.
Recalibration
It is recommended that calibration of the thermometers be
performed annually.
omega.com [email protected]
Servicing North America:
U.S.A.:
Omega Engineering, Inc., One Omega Drive,
P.O. Box 4047, Stamford, CT 06907-0047 USA
Toll-Free: 1-800-826-6342 (USA & Canada only)
Customer Service: 1-800-622-2378 (USA & Canada only)
Engineering Service: 1-800-872-9436 (USA & Canada only)
Tel: (203) 359-1660
Fax: (203) 359-7700
e-mail: info @omega.com
For Other Locations Visit
omega.com/worldwide
The information contained in this document is believed to
be correct, but OMEGA accepts no liability for any errors it
contains, and reserves the right to alter specifications without
notice.
OMEGA ENGINEERING, INC., warrants this unit to be free of defects in materials and workmanship for a period of 13 months from
WARRANTY/DISCLAIMER
date of purchase. OMEGA’s WARRANTY adds an additional one (1) month grace period to the normal one (1) year product warranty
to cover handling and shipping time. This ensures that OMEGA’s customers receive maximum coverage on each product.
If the unit malfunctions, it must be returned to the factory for evaluation. OMEGA’s Customer Service Department will issue an
Authorized Return (AR) number immediately upon phone or written request. Upon examination by OMEGA, if the unit is found
to be defective, it will be repaired or replaced at no charge. OMEGA’s WARRANTY does not apply to defects resulting from any
action of the purchaser, including but not limited to mishandling, improper interfacing, operation outside of design limits, improper
repair, or unauthorized modification. This WARRANTY is VOID if the unit shows evidence of having been tampered with or shows
evidence of having been damaged as a result of excessive corrosion; or current, heat, moisture or vibration; improper specification;
misapplication; misuse or other operating conditions outside of OMEGA’s control. Components in which wear is not warranted,
include but are not limited to contact points, fuses, and triacs.
OMEGA is pleased to offer suggestions on the use of its various products. However, OMEGA neither assumes responsibility
for any omissions or errors nor assumes liability for any damages that result from the use of its products in accordance with
information provided by OMEGA, either verbal or written. OMEGA warrants only that the parts manufactured by the company
will be as specified and free of defects. OMEGA MAKES NO OTHER WARRANTIES OR REPRESENTATIONS OF ANY KIND
WHATSOEVER, EXPRESSED OR IMPLIED, EXCEPT THAT OF TITLE, AND ALL IMPLIED WARRANTIES INCLUDING ANY WARRANTY
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED. LIMITATION OF LIABILITY: The
remedies of purchaser set forth herein are exclusive, and the total liability of OMEGA with respect to this order, whether based on
contract, warranty, negligence, indemnification, strict liability or otherwise, shall not exceed the purchase price of the component
upon which liability is based. In no event shall OMEGA be liable for consequential, incidental or special damages.
CONDITIONS: Equipment sold by OMEGA is not intended to be used, nor shall it be used: (1) as a “Basic Component” under 10
CFR 21 (NRC), used in or with any nuclear installation or activity; or (2) in medical applications or used on humans. Should any
Product(s) be used in or with any nuclear installation or activity, medical application, used on humans, or misused in any way,
OMEGA assumes no responsibility as set forth in our basic WARRANTY/DISCLAIMER language, and, additionally, purchaser will
indemnify OMEGA and hold OMEGA harmless from any liability or damage whatsoever arising out of the use of the Product(s) in
such a manner.
Direct all warranty and repair requests/inquiries to the OMEGA Customer Service Department. BEFORE RETURNING ANY
PRODUCT(S) TO OMEGA, PURCHASER MUST OBTAIN AN AUTHORIZED RETURN (AR) NUMBER FROM OMEGA’S CUSTOMER
SERVICE DEPARTMENT (IN ORDER TO AVOID PROCESSING DELAYS). The assigned AR number should then be marked on the
outside of the return package and on any correspondence.
The purchaser is responsible for shipping charges, freight, insurance and proper packaging to prevent breakage in transit.
FOR WARRANTY RETURNS, please have the following
information available BEFORE contacting OMEGA.
1. Purchase order number which the product was
PURCHASED,
2. Model and serial number of the product under warranty, and
3. Repair instructions and/or specific problems relative to
the product.
OMEGA’s policy is to make running changes, not model changes, whenever an improvement is possible. This affords cust omers
the latest technology and engineering.
OMEGA is a registered trademark of OMEGA ENGINEERING, INC.
© COPYRIGHT 2015 OMEGA ENGINEERING, INC. All rights reserved. This document may not be copied, photocopied,
translated, or reduced to any electronic medium-readable form, in whole or in part, without the prior written consent of OMEGA
ENGINEERING, INC.
RETURN REQUESTS/INQUIRIES
FOR NON-WARRANTY RETURNS, consult OMEGA for
current repair charges. Have the following information
available BEFORE contacting OMEGA.
1. Purchase Order number to cover the COST of the repair,
2. Model and serial number of the product and
3. Repair instructions and/or specific problems
relative to the product.
Loading...