OMEGA BB702 Manual

TM

User’s Guide

Shop online at

omega.com

e-mail: [e-mail]

For latest product manuals:

www.omegamanual.info

BB702

Blackbody Calibrator

omega.com [e-mail]

Servicing North America:

U.S.A. Omega Engineering, Inc.
Headquarters: Toll-Free: 1-800-826-6342 (USA & Canada only)

Customer Service: 1-800-622-2378 (USA & Canada only)
Engineering Service: 1-800-872-9436 (USA & Canada only)
Tel: [phone] Fax: [phone]
e-mail: [e-mail]

For Other Locations Visit omega.com/worldwide

The information contained in this document is believed to be correct, but OMEGA accepts no liability for any errors it contains, and reserves
the right to alter specifications without notice.

Table of Contents

Section ............................................................................. Page

Section 1 Introduction ................................................................................ 1-1

1.1 Precautions ............................................................................. 1-1

1.2 Safety Warnings and IEC Symbols ..................................... 1-1

1.3 General Desrciption ............................................................... 1-2

Section 2 Installation .................................................................................. 2-1

2.1 Unpacking and Inspection ................................................... 2-1

2.2 Mounting ................................................................................ 2-1

2.3 Ambient Temperature .......................................................... 2-1

2.4 Power Connection ................................................................. 2-2

Section 3 Operation ..................................................................................... 3-1

3.1 Front Panel Controls and Indicators .................................. 3-1

3.2 Back Panel Connections ....................................................... 3-2

3.3 Changing the Temperature Setpoint .................................. 3-3

3.4 Changing the Controller Parameters ................................. 3-3

3.5 Heat Up / Cool Down Cycle Times ................................... 3-5

3.6 Overheat Reset Switch ......................................................... 3-5

BB702 Blackbody Calibrator

Table of

Contents

Section 4 Serial Communication .............................................................. 4-1

Section 5 Maintenance ................................................................................ 5-1

5.1 Calibration ............................................................................. 5-1

5.2 Cleaning ................................................................................. 5-1

5.2.1 Main Body ........................................................................... 5-1

5.2.2 Target Plate ......................................................................... 5-1

5.2.3 Fan ........................................................................................ 5-1

5.3 Fuse Replacement ................................................................. 5-1

Section 6 Reference Probe ......................................................................... 6-1

Section 7 Specifications .............................................................................. 7-1

Section 8 Troubleshooting Guide ............................................................ 8-1

Section 9 Glossary of Terms Used in This Manual .............................. 9-1

Section 10 The OMEGA Family of Blackbody Calibrators ................. 10-1

i

Table of

Figures

BB702 Blackbody Calibrator

Table of Figures

Figure Description Page

1 I.E.C. Symbols .............................................................................. 1-2

2 Maximum Setpoint Temperature Limits ................................. 2-2

3 Front Panel ................................................................................... 3-1

4 Back Panel .................................................................................... 3-2

5 Menu Hierarchy Showing Factory Default Settings .............. 3-4

6 Programming Procedure ........................................................... 3-4

7 Heat Up / Cool Down Cycle Time Table ................................ 3-5

8 Connecting the BB702 to a Computer’s Serial Port ................ 4-1

9 Internal Reference Probe Connections ................................... 6-1

ii

Section 1 - Introduction

Your BB700 Series Blackbody Calibration Source has been designed for ease of
use and reliability whenever you have the need to test or calibrate non-contact
infrared temperature instruments. It is important that you read this manual
completely and follow all safety precautions before operating this instrument.

1.1 Precautions

• Follow all safety precautions and operating instructions outlined in this
manual. If this instrument is not used in a manner specified by the manual, the
protection provided by the equipment may be impaired.

• Never leave your calibrator unattended when in use.

• Keep out of reach of all children.

• Never touch the target plate when hot.

• Never place any object within 3 inches of the cavity opening when hot.

• Do not operate in flammable or explosive environments.

BB702 Introduction

1

• Never operate with a power cord other than the one provided with your unit.

• Check that the power cord is not cracked, frayed or damaged before
connecting to device and powering up.

• Remove and or disconnect main power before attempting any maintenance or
fuse replacement.

• Do not connect and or operate this unit to a non-grounded, non-polarized
outlet or power source.

• Do not connect the serial port or reference probe port to equipment with
exposed, hazardous, live voltages.

• Any connections to the serial port or reference port should be made with Class
II insulation or better.

• Protect from moisture or rain.

NOTE:

There are no user serviceable parts inside your unit. Attempting to repair or service your unit
may void your warranty.

1.2 Safety Warnings and IEC Symbols

This device is marked with international safety and hazard symbols in
accordance with IEC 1010. It is important to read and follow all precautions and
instructions in this manual before operating or commissioning this device as it
contains important information relating to safety and EMC. Failure to follow all
safety precautions may result in injury and or damage to your calibrator. Use of
this device in a manner not specified by the manufacturer may impair protection
provided within the unit.

1-1

1

BB702 Introduction

IEC symbols Description

Caution, risk of electric shock

Caution, refer to accompanying
documents

Caution, hot surface

1.3 General Description

The Model BB702 is a portable, rugged, bench-top, blackbody calibration source
with a built-in precision PID digital controller. The calibrator is used to test
and calibrate infrared pyrometers. The 2.5 inch Diameter target plate has an
emissivity of 0.95 and can be set to any temperature between ambient +11 to
215°C (ambient +20 to 420°F).

230 VAC @50/60Hz (European Models)
115 VAC @50/60Hz (Domestic Models)

Figure 1. IEC symbols

1-2

Section 2 - Installation

2.1 Unpacking

Remove the packing list and verify that you have received all your equipment.
If you have any questions about the shipment, please call our Customer Service
Department.

We can also be reached on the Internet.

When you receive the shipment, inspect the container and equipment for any
signs of damage. Note any evidence of rough handling in transit. Immediately report
any damage to the shipping agent.

The carrier will not honor any damage claims unless all shipping material is saved for
inspection. After examining and removing contents, save packing material and carton in the
event reshipment is necessary.

The following items are supplied in the box:

NOTE:

BB702 Installation

2

• BB702 Blackbody Calibration Source

• User’s Manual

• Calibration Certificate

• Power Cord

• Reference Port Cord Plug Connector

2.2 Mounting

Mount the unit on a bench, table top or shelf in a horizontal position and operate
at least ten inches from any air obstructions to the fan, front panel, rear panel,
bottom and top of the unit, in an ambient environment between the specified
5 to 45°C (41 to 113°F).

2.3 Ambient Temperature

The target plate of the BB702 can achieve any temperature within the specified tem­perature range when being operated in ambient temperature up to 32.2°C (90°F).
When operating the unit at higher ambient temperatures, the user must not exceed
the “Maximum Allowable Target Plate Temperature” shown along the y-axis in
Figure 2. Failure to adhere to these guidelines may cause a safety switch inside the
unit to open the heater circuit. If the PID light is blinking or continuously on but there
is no increase in target plate temperature, then the thermal safety switch has tripped.
In this case refer to Section 3-6. When ambient temperatures exceeds 32.2°C (90°F),
every increase in ambient temperature of 2.8°C (5°F) must be accompanied by a
decrease in maximum target plate temperature of 11.1°C (20°F).

2-1

2

AMBIENT TEMPERATURE (C)

MAXIMUM ALLOWABLE

BB702 Installation

29.4 32.2 35.0 37.8 40.6 43.3 46.2

420

215.6

400

380

OPERATING

REGION

360

340

TARGET PLATE TEMPERATURE (F)

320

85 9590 100 105 110 115

Figure 2. Limitation of Maximum Setpoint Temperature at Elevated Ambient

2.4 Power Connection

Standard (115 VAC~, 50/60 Hz models)

The BB702 comes with a standard North American 3-prong AC power cord. Do
not use any other power cord other than the one provided. This cord provides
the proper grounding and has been safety tested by the proper safety agencies.

AMBIENT TEMPERATURE (F)

Temperature.

204.4

193.3

182.2

171.1

160.0

MAXIMUM ALLOWABLE

TARGET PLATE TEMPERATURE (C)

International (230 VAC~, 50/60 Hz models)

On 230 VAC~, 50/60Hz models a European style power cord with the proper
color code and approvals is provided with stripped wire ends for connection
to the proper connector used in your country or local area, this connector is not
provided.

CAUTION:

• Line voltage variations are not to exceed ±10% of the rated input voltage.

• Electrical connections and wiring should be performed only by suitably trained

personal.

• To shut down the unit in an emergency, the power cord can be disconnected from

the AC outlet on the rear of the unit.

2-2

Section 3 - Operation

3.1 Front Panel Controls and Indicators

SETPOINT TEMPERATURE

PROCESS TEMPERATURE TARGET PLAT E

420.0 PV

420.0 SV

BB702 Operation

BLACK
POINT

T

Temperature

90F/32C

Range

Blackbody

BB702

420F/215C

3

ON/STAND-BY
POWER SWITCH

PARAMETER/
ACCESS KEY

MODE KEY TEMPERATURE RANGE

LOWER SETPOINT KEY

RAISE SETPOINT KEY

REFERENCE BAR

Figure 3. Front Panel

Process Temperature:

This field displays the current temperature of the target plate.

Setpoint Temperature:

This field displays the desired target plate temperature. Once the target plate
reaches this desired temperature, both displays will read the same value.

Target Plate:

The 4.0" target plate is a near ideal blackbody source. The emissivity of the plate
is .95. When calibrating an IR pyrometer, hold the pyrometer perpendicular to
the target plate for optimal performance. The proper distance between the IR
pyrometer and the target plate depends on the field of view of the pyrometer.
If the pyrometer is too far away it will scan unwanted surfaces outside of the
perimeter of the target plate. Holding the pyrometer too close could introduce
undesirable heat to the IR detector of the pyrometer.

CAUTION:

The BB702’s target plate can be set to very high temperatures. Exercise extreme
caution when operating the unit. Keep hands and fingers away from the target plate
area. Keep flammable products such as paper, plastics and clothing far from the
BB702.

3-1

3

BB702 Operation

NOTE:

P.I.D. Control:
Proportional, integral, derivative control ( P.I.D.) is a temperature control algorithm used
in high-end temperature controllers. The controller causes the process to attain the desired
temperature by turning the process on or off. The process may be a heater or refrigerator. As
the process temperature approaches the setpoint temperature the hot or cold process will be
pulsed to reduce the corrective measures and minimize overshooting. The controller provides
a visual representation of the process status through LED indicators. An indicator may be lit
continuously, blink or shut off entirely to indicate that the process is on, being pulsed, or off,
respectively.

Parameter/Access Key:

Press to scroll through menu parameters

Raise Key:

Press to increase the selected parameter or scroll upward in the list of possible
settings.

Lower Key:

Press to decrease the selected parameter or scroll downward in the list of
possible settings.

Mode Key:

Press to save settings and exit a menu level.

3.2 Back Panel Connections

RTD REFERENCE
PROBE CONNECTION

FUSE

3-2

FAN

RS-232 COMMUNICATIONS PORT

Figure 4. Back Panel

AC MAINS POWER INPUT
AND FUSE COMPARTMENT

AC Power Mains Input and Fuse Compartment:

The customer connects the power cord to the AC Power Input. As a safety
precaution, the power cord cannot be connected if the fuse compartment is open.
Refer to Section 5.3 for information on fuse replacement.

Reference Probe Connection:

The reference probe enables the user to monitor the target plate temperature with
an external instrument. The wires are connected to a Class A, 0.00385 RTD Sensor.

Refer to Section 6 for pinout details.

RS232 Communications Port:

The female DB-9 port allows the customer to make a 3-wire RS232 interface with
the BB-702. A detailed description of this port is described in Section 4.

3.3 Changing the Temperature Setpoint

The layout of the front panel is shown in Figure 3. The BB702 incorporates a PID
digital setpoint controller. The upper display indicates the blackbody target plate
temperature known as (PV) Process Variable, while the lower display indicates the
programmed setpoint known as (SV) Setpoint Variable. Making changes to the
setpoint, units of measure and communication settings are made via the
“

” and “ “ keys. Holding a key in, continuously, will cause the setpoint

temperature to advance more quickly to a desired value. Three
scanning speeds are provided: slow, medium and fast. The minimum and
maximum setpoints are locked.

BB702 Operation

3

3.4 Changing the Controller Parameter Settings

The BB702 operates at its optimum performance when left with its factory
parameter settings. The only internal parameter that the operator should need to
change is the engineering units (°F or °C), or serial communications parameters.
Below are two figures: a) menu hierarchy with factory default settings;
b) programming procedure.

CAUTION:

Changing any parameter other than engineering units could defeat safety features of the unit
rendering it unsafe to operate.

3-3

3

BB702 Operation

Menu 00 Menu 01 Menu 02 Menu 03 Menu 04 Menu 05

Key Lock SETPOINT Ac.Cd =02 Ac.Cd =03 Ac.Cd =04 Ac.Cd =05

Ac.Cd

Gn.o1 434 ALr1 440 id.no 01 SnSr P

Gr.o2 ALr2 BAUd 12.o.7 Sn.00

rAtE 4 Cy.t1 0 CAL.L dEC.P

rSEt 21 Cy.t2 CAL.H FILt

H.Hys SP.tt OFF OUt.1 Ht.P

HyS.1 L.SP.L 90 OUt.2 Alr

C.HyS L.SCL CoL.t nor

HyS.2 U.SP.L 420 A1.HL HI

C.SPr H.SCL A1.Pd Pr

SPr.2 A1.OP LAt

dPnG nl A2.HL Hl

A2.Pd Pr

A2.OP OFF

Unit F

Figure 5. Menu Hierarchy Showing Factory Default Settings

NOTE:

Only the boldface parameters are active for the default mode
of operation.

Changing the Controller’s Parameter Settings

1. Press the

key to enter the programming mode. The lower display will

alternately display the menu level and “Ac.Cd.”

2. Use the and keys to change to the desired menu level.

3. Once you have chosen the desired menu use the

the parameters. To change the setting of a given parameter, use the

key to scroll through

and

keys.

4. To save settings press the

key. The controller now exits the programming

menu and return to the normal operating mode.

5. To change settings on other menu levels, you must re-enter the programming

menu (from step #1).

Putting the Controller In or Out of Standby Mode

1. To enter the Standby mode hold the

key for 4 seconds until the window

flashes “StbY”.

3-4

2. To exit the Standby mode hold the

key for 4 seconds until the window
flashes “tUne”. Then press the key for 4 seconds again until “tUne” stops
flashing.

Figure 6. Programming Procedure

3.5 Heat-Up/Cool-Down Cycle Times

Approximate cycle times for heat up and cool down are given in Fig. 7. To find
a transition time from one plate temperature to another follow this procedure:
Look for an initial temperature in the left column. Next, look for the final
temperature along the top row. The intersection of the row and column provides
the approximate transition time.

TO: 37.8C 121.1C 204.4C

FROM: 100F 250F 400F

37.8C 100F 4.5 MIN. 20 MIN.

121.1C 250F. 35 MIN. 7.5 MIN.

204.4C 400F 45 MIN. 9.5 MIN.

Figure 7. Heat Up/ Cool Down Cycle Time Table.

3.6 Overheat Reset Switch

BB702 Operation

3

If the unit is operated at high temperatures in elevated ambient temperatures, an
overheat condition may occur. In an overheat situation a mechanical reset switch
near the right handle hinge will pop and open the heater circuit. The controller
will still have power. While the controller will be demanding heat from the
heater, the process temperature will fall continuously until it equalizes with the
room temperature. If an overheat condition occurs, let the unit cool off for one
hour (leave the unit on), then press the reset button, firmly. If the reset switch
keeps resetting, call OMEGA’s Customer Service Department.

3-5

4

BB702 RS232 Communications

Section 4 - RS232 Communication

The RS232 port allows customers to send Setpoint information to the BB702 and
record process temperature from the BB702 via a computer. The port enables
bi-directional data transfer via a three-conductor cable consisting of signal
ground, receive input, and transmit output. It is recommended that less than
fifty feet of shielded cable be used between the computer and this instrument.
This will assure performance of the BB702 to EN61326, under the E.M.C. Note
that multiple instruments cannot be tied to the same port in this configuration.
The RS232 port is optically isolated to eliminate ground loop problems.

Below is a pinout diagram for the serial port of the BB702 as well as the pinout
for a 9-pin PC serial port. Use a straight DB9 (female) to DB9 (male) connector
cable to connect your computer to the BB702. The cable should be attached when
the computer and BB702 are off.

Only parameters in the parameter list should be modified or queried via the
serial port. Other parameters should be viewed or queried from the controller,
directly. It is highly recommended that baud rate for the controller be modified
on the controller, directly. Note that both the BB702 and the computer must be
communicating with the same serial communications parameters to establish a
working communication link.

The serial communications feature can be tested using terminal emulation
package. Note that this controller does not time out waiting for the next
character to be transmitted. Be sure not to use the XON/XOFF or hardware
handshaking. Lastly, it should be noted that following a complete transmission
to the BB702, a response it sent back. If the message was valid, the changed or
queried parameter is echoed back (following the same format). If the message
was not according to acceptable format or was attempting to force a parameter
out of range, an “ERROR” message is echoed.

1

BB702

BLACKBODY

CALIBRATOR

2345

6789

TX

RX

RX

TX

GND

GND

4-1

COMPUTER

SERIAL

PORT

(RS232)

Figure 8. Connecting the BB702 to a Computer’s Serial Port

12 345

6789

BB702 Communications

Parameter List (only relevant parameters shown):

PAR#: Parameter: Range/Units:

00 Process Temp. Input determined

01 Setpoint Input determined

19 Baud Selection bAUd

Baud Selections:

Code: Baud: Parity: Data Bits: Stop Bits:

3.o.7 300 odd 7 2

6.o.7 600 odd 7 2

12.o.7 1200 odd 7 2 (factory default settings)

24.o.7 1200 odd 7 2

3.n.8 300 no 8 1

6.n.8 600 no 8 1

12.n.8 1200 no 8 1

4

24.n.8 2400 no 8 1

General Message Format:

#[controller id][command][parameter number]<new value><units>[CR/LF]

Definitions:

# - This character initiates an “escape sequence” that the controller will
recognize.

[controller id] – Up to 2 numeric characters, “00” to “99” (factory default=”01”)

[command] – 1 character, upper case or lower case

“R” – To read a parameter from the controller

“M” – To temporarily modify a controller parameter (lost upon shutdown)

“E” – To modify a controller param. in non-volatile mem. (saved even after

shutdown)

[parameter #] – Up to 2 numeric characters, “00” to “99”

<new value> - This control word is used only when entering or modifying a

parameter. Up to 6 characters may be entered. The first character
can be a space, a “+”, or a “-”. The next 4 characters are for
entering the new value parameter value. Be sure to use the exact
same field format as is currently being used. (i.e. if the XXX.X
format is used to express temperature, be sure to enter a new
value that conforms to the same format).

<units> - This optional control word is used to specify units, F for °F, C for °C.

[CR/LF] – Every transmission must be terminated with a carriage return [CR]
character. The line feed [LF] character is optional.

4-2

5

BB702 Maintenance

Section 5 - Maintenance

5.1 Calibration

This unit has been fine tuned at the factory and calibrated to give optimum
performance of its full temperature range. It is recommended that the unit be
returned annually for re-calibration.

5.2 Cleaning

Remove all electrical connections and power before
attempting any maintenance or cleaning.

5.2.1 Main Body

Only a damp, soft rag with a mild cleaning solution should be used when
cleaning the main body of this unit.

5.2.2 Target Plate

Do not attempt to clean the target plate. The target plate has a special coating
applied and cleaning may change the emissivity and performance of your unit.

5.2.3 Fan

The fan filter should be cleaned monthly as a minimum by washing the filter
with warm water and then blowing dry with air. It can be removed by firmly
pulling the black plastic frame outward. The internal protective grill that is
seated against the fan can be cleaned with a soft bristle brush.

CAUTION:

5.3 Fuse replacement

Disconnect all power from source before attempting fuse replacement.

For continued protection against the risk of fire replace with only the same size, type
and rating fuse indicated here and on the rear panel of your unit.

For model: BB702 use 1 ea. 250 VAC~, T1A (Time-Lag, 1 Amp)

For model: BB702-230VAC use 2 ea. 250 VAC~, T0.5A (Time-Lag, 0.5 Amp)

WARNING:

CAUTION:

UL./CSA APPROVED (0.25" dia. x 1.25" long).

VDE APPROVED (5 mm dia. x 20 mm long).

5-1

Section 6 - Reference Probe

An electrically isolated 100Ω Class A RTD probe has been embedded into the

target plate heater assembly to be used as a reference. This feature is commonly
used in conjunction with a precision thermometer, ohmmeter or temperature
recording device. The maximum current being passed through the RTD should
never exceed 0.3 mA (constant DC). A connector has been provided with your
calibrator for connection to this reference probe. Notice that at each temperature,
a given resistance will be measured at the reference port. The resistance is
measured across PIN1-PIN2 or across PIN1-PIN3. PIN2 and PIN3 are connected
to the same side of the RTD.

BB702 Reference Probe

6

TARGET PLATE ASSEMBLY

BLACK WIRE

RED WIRE

BLACK WIRE

RTD REFERENCE PROBE

Figure 9. Internal Reference Probe Connections

1

2

3

REFERENCE
PROBE
CONNECTOR

6-1

7

BB702 Specifications

Section 7 - Specifications

Target Plate Temperature Range: Amb. + 11 to 215°C (Amb. + 20 to 420°F)

Accuracy: ±0.5°C, ±0.25% rdg

(±0.9°F, ±0.25% rdg)

Stability: ±0.1°C (±0.2 °F )

Ambient Environmental Conditions

Temperature: 5 to 45 °C (41 to 113°F)
Humidity: 0 to 90% RH, Non-condensing

Target Plate Size: 63.5 mm (2.5")

Target Plate Emissivity: 0.95*

Internal Control Sensor: Platinum RTD, Class A, Alpha = 0.00385

Reference Sensor: Platinum RTD, Class A, Alpha = 0.00385

Warm-up Time: See Figure 7, Section 3.5

Cool-down Time: See Figure 7, Section 3.5

Power

BB702: 115 VAC~, 50/60 Hz, 75W.
BB702-230VAC: 230 VAC~, 50/60 Hz, 75W

Dimensions: 152 x 305 x 280 mm
(6 H x 12 W x 11"L)

Weight: 7.2 kg (16 lb)

Installation Category II

* Reference to 8-14 micons wavelength bandwidth.

7-1

BB702 Troubleshooting Guide

8

Section 8 - Troubleshooting Guide

Problem Solution

1. Unit will not turn on. a. Check Power Cord connections.

b. Check rear panel fuse(s).
c. Unit requires service, contact our

customer service department.

2. Unit turns on but the target a. Check that you have entered a setpoint
plate will not get hot. between Ambient +20 to 420°F.

b. Verify that the controller is set to its

factory default settings.

c. Unit has overheated causing the

thermal reset switch to open. See Section

3.6.

d. Unit requires service, contact our
customer service department.

3. Controller display shows “Error” a. Unit requires service, contact our
and the target will not get hot. customer service department.

4. Cavity cone temperature will not a. Verify that the controller is set to its
stabilize to within ±2°F of the factory default settings.
setpoint temperature. b. Unit requires service, contact our
customer service department.

5. Unable to communicate with the a. Check that you have made the proper
unit through the RS232 wiring connections between your unit
connection port. and computer.
b. Check for proper communication
parameter settings in the controller and
your computer, Baud, parity, etc...
c. Check that your message string contains

the correct letters and characters for the
command you want to send.

d. Unit requires service, contact our
customer service department.

8-1

9

BB702 Glossary of Terms Used in This Manual

Section 9 - Glossary of Terms Used in This Manual

Blackbody

A theoretical object that radiates the maximum amount of energy at a given
temperature, and absorbs all the energy incident upon it.

Calibration

The process of adjusting an instrument or compiling a deviation chart so that its
reading can be correlated to the actual value being measured.

Emissivity

The ratio of energy emitted by a surface to the energy emitted by a blackbody at
the same temperature.

IEC

International Electrotechnical Commission

Infrared (IR)

A range of the electromagnetic spectrum extending beyond red visible light from
760 nanometers to 1000 microns.

PID

Proportional, Integral, Derivative. A three mode control action where the
controller has time proportioning, integral (auto reset) and derivative rate action.

RTD

Resistance temperature detector

9-1

The OMEGA Family of Blackbody Calibrators

10

The OMEGA

Listed below is a selection guide of OMEGA’s current line of blackbody calibration
sources in addition to the one you have selected. This family of rugged, portable and
accurate calibrators cover a wide range of temperatures, target plate sizes and features
making them perfect for infrared pyrometer field service testing and laboratory
calibrations.

BB701 Hot/Cold Blackbody Calibration Source
Calibration Range: -18 to 149°C (0 to 300°F) Accuracy: ±0.8°C (±1.4 °F)
Emissivity: 0.95 Ambient Temp.: 4 to 43°C (40 to 110°F)
Cavity Size: 63.5 mm (2.5 in.) Power: 115/230V, 50/60 Hz, 175W

BB702 Blackbody Calibration Source
Calibration Range: 32 to 215°C (amb. 90 to 420°F) Accuracy: ± 0.5°C (±0.9°F), ±0.25% rdg.
Emissivity: 0.95 Ambient Temp.: 5 to 45°C (41 to 113°F)
Cavity Size: 63.5 mm (2.5 in.) Power: 115/230V, 50/60 Hz, 75W

BB703 Mini Blackbody Calibration Source
Calibration Range: 32 to 400°C (90 to 752°F) Accuracy: ±1.4°C (±2.5°F)
Emissivity: 0.95 Ambient Temp.: 0 to 40°C (32 to 104°F)
Cavity Size: 28.6 mm (1.125 in.) Power: 115/230V, 50/60 Hz, 175W

Family of Blackbody Calibrators

BB704 4” Target Plate Blackbody Calibration Source
Calibration Range: 100 to 400°C (212 to 752°F) Accuracy: ±0.8°C (±1.4°F)
Emissivity: 0.95 Ambient Temp.: 0 to 50°C (32 to 122°F)
Cavity Size: 101.6 mm (4 in.) Power: 115/230V, 50/60 Hz, 425W

BB705 Laboratory Grade Blackbody Calibration Source
Calibration Range: 100 to 1046°C (212 to 1915°F) Accuracy: ±1.0°C (±1.8°F), ±0.25% rgd
Emissivity: 0.99 Ambient Temp.: 0 to 35°C (32 to 95°F)
Cavity Size: 44 mm (1.75 in.) Power: 115/230V, 50/60 Hz, 1100W

BB-4A High Temperature Blackbody Calibration Source
Calibration Range: 100 to 982°C (212 to 1800°F) Accuracy: ±1.0°C (±1.8°F), ±0.25% rdg
Emissivity: 0.99 Ambient Temp.: 0 to 50°C (32 to 122°F)
Cavity Size: 22.2 mm (0.88 in.) Power: 115/230V, 50/60 Hz, 400W

For a complete, updated specification sheet and price on any of the calibrators listed here visit our
website at www.omega.com. Please call our sales or customer service department for information
and pricing on any new models available.

10-1

10

NOTES:

10-2

WARRANTY/DISCLAIMER

OMEGA ENGINEERING, INC. warrants this unit to be free of defects in materials and workmanship for a
period of 25 months from date of purchase. OMEGA’s WARRANTY adds an additional one (1) month grace
period to the normal one (2) year product warranty to cover handling and shipping time. This ensures
that OMEGA’s customers receive maximum coverage on each product.

If the unit malfunctions, it must be returned to the factory for evaluation. OMEGA’s Customer Service
Department will issue an Authorized Return (AR) number immediately upon phone or written request.
Upon examination by OMEGA, if the unit is found to be defective, it will be repaired or replaced at no
charge. OMEGA’s WARRANTY does not apply to defects resulting from any action of the purchaser,
including but not limited to mishandling, improper interfacing, operation outside of design limits,
improper repair, or unauthorized modification. This WARRANTY is VOID if the unit shows evidence of
having been tampered with or shows evidence of having been damaged as a result of excessive corrosion;
or current, heat, moisture or vibration; improper specification; misapplication; misuse or other operating
conditions outside of OMEGA’s control. Components in which wear is not warranted, include but are not
limited to contact points, fuses, and triacs.

OMEGA is pleased to offer suggestions on the use of its various products. However,
OMEGA neither assumes responsibility for any omissions or errors nor assumes liability for
any damages that result from the use of its products in accordance with information provided
by OMEGA, either verbal or written. OMEGA warrants only that the parts manufactured by the
company will be as specified and free of defects. OMEGA MAKES NO OTHER WARRANTIES OR
REPRESENTATIONS OF ANY KIND WHATSOEVER, EXPRESSED OR IMPLIED, EXCEPT THAT OF
TITLE, AND ALL IMPLIED WARRANTIES INCLUDING ANY WARRANTY OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED. LIMITATION OF
LIABILITY: The remedies of purchaser set forth herein are exclusive, and the total liability of
OMEGA with respect to this order, whether based on contract, warranty, negligence,
indemnification, strict liability or otherwise, shall not exceed the purchase price of the
component upon which liability is based. In no event shall OMEGA be liable for
consequential, incidental or special damages.

CONDITIONS: Equipment sold by OMEGA is not intended to be used, nor shall it be used: (1) as a “Basic
Component” under 10 CFR 21 (NRC), used in or with any nuclear installation or activity; or (2) in medical
applications or used on humans. Should any Product(s) be used in or with any nuclear installation or
activity, medical application, used on humans, or misused in any way, OMEGA assumes no responsibility
as set forth in our basic WARRANTY/DISCLAIMER language, and, additionally, purchaser will indemnify
OMEGA and hold OMEGA harmless from any liability or damage whatsoever arising out of the use of the
Product(s) in such a manner.

RETURN REQUESTS/INQUIRIES

Direct all warranty and repair requests/inquiries to the OMEGA Customer Service Department. BEFORE
RETURNING ANY PRODUCT(S) TO OMEGA, PURCHASER MUST OBTAIN AN AUTHORIZED RETURN (AR)
NUMBER FROM OMEGA’S CUSTOMER SERVICE DEPARTMENT (IN ORDER TO AVOID PROCESSING
DELAYS). The assigned AR number should then be marked on the outside of the return package and on any
correspondence.

The purchaser is responsible for shipping charges, freight, insurance and proper packaging to prevent
breakage in transit.

FOR WARRANTY RETURNS, please have the
following information available BEFORE contacting
OMEGA:

1. Purchase Order number under which the product
was PURCHASED,

2. Model and serial number of the product under
warranty, and

3. Repair instructions and/or specific problems

relative to the product.

OMEGA’s policy is to make running changes, not model changes, whenever an improvement is possible. This affords our
customers the latest in technology and engineering.

OMEGA is a trademark of OMEGA ENGINEERING, INC.
© Copyright 2017 OMEGA ENGINEERING, INC. All rights reserved. This document may not be copied, photocopied,

reproduced, translated, or reduced to any electronic medium or machine-readable form, in whole or in part, without the prior
written consent of OMEGA ENGINEERING, INC.

FOR NON-WARRANTY REPAIRS, consult
OMEGA for current repair charges. Have
the following information available BEFORE
contacting OMEGA:

1. Purchase Order number to cover the COST
of the repair,

2. Model and serial number of the product, and

3. Repair instructions and/or specific problems
relative to the product.

Where Do I Find Everything I Need for

Process Measurement and Control?

OMEGA…Of Course!

Shop online at omega.com

TEMPERATURE

MU

Thermocouple, RTD & Thermistor Probes, Connectors,

Panels & Assemblies

MU

Wire: Thermocouple, RTD & Thermistor

MU

Calibrators & Ice Point References

MU

Recorders, Controllers & Process Monitors

MU

Infrared Pyrometers

PRESSURE, STRAIN AND FORCE

MU

Transducers & Strain Gages

MU

Load Cells & Pressure Gages

MU

Displacement Transducers

MU

Instrumentation & Accessories

FLOW/LEVEL

MU

Rotameters, Gas Mass Flowmeters & Flow Computers

MU

Air Velocity Indicators

MU

Turbine/Paddlewheel Systems

MU

Totalizers & Batch Controllers

pH/CONDUCTIVITY

MU

pH Electrodes, Testers & Accessories

MU

Benchtop/Laboratory Meters

MU

Controllers, Calibrators, Simulators & Pumps

MU

Industrial pH & Conductivity Equipment

DATA ACQUISITION

MU

Communications-Based Acquisition Systems

MU

Data Logging Systems

MU

Wireless Sensors, Transmitters, & Receivers

MU

Signal Conditioners

MU

Data Acquisition Software

HEATERS

MU

Heating Cable

MU

Cartridge & Strip Heaters

MU

Immersion & Band Heaters

MU

Flexible Heaters

MU

Laboratory Heaters

ENVIRONMENTAL
MONITORING AND CONTROL

MU

Metering & Control Instrumentation

MU

Refractometers

MU

Pumps & Tubing

MU

Air, Soil & Water Monitors

MU

Industrial Water & Wastewater Treatment

MU

pH, Conductivity & Dissolved Oxygen Instruments

M3015/1217