Omcan Food Machinery SE-CN-0203 Installation Manual

Impulse Sealers

Models SE-CN-0203, 0305, 0406 and 0508

Instruction Manual

Revised - 9/22/2014

Toll Free: 1-800-465-0234

Fax: 905-607-0234

Email: sales@omcan.com

www.omcan.com

Table of Contents

Model SE-CN-0203 / Model SE-CN-0305 Model SE-CN-0406 / Model SE-CN-0508

Section

General Information

Safety and Warranty

Technical Specications

Operation

Parts Breakdowns

Electrical Schematics

--------------------------------------------------------------------------------------------- 5

-------------------------------------------------------------------------------- 3

--------------------------------------------------------------------------- 3 - 4

----------------------------------------------------------------------------- 6 - 7

------------------------------------------------------------------------------ 8

Page

-------------------------------------------------------------------------- 4

Notes

Warranty Registration

-------------------------------------------------------------------------------------------- 9 - 10

---------------------------------------------------------------------------- 11

2

General Information

Omcan Manufacturing and Distributing Company Inc. and Food Machinery of America, Inc. dba Omcan are not responsible for any harm or injury caused due to any person’s improper or negligent use of this equipment. The product shall only be operated by someone over the age of 18, of sound mind, and

not under the inuence of any drugs or alcohol, who has been trained in the correct operation of this machine, and is wearing authorized, proper safety clothing. Any modication to the machine voids any warranty, and may cause harm to individuals using the machine or in the vicinity of the machine while

in operation.

The Impulse Sealer is used to ensure a water tight and air tight seal for effective packing and sterilization procedures.

CHECK PACKAGE UPON ARRIVAL

Upon receipt of an Omcan shipment please inspect for external damage. If no damage is evident on the external packaging, open carton to ensure all ordered items are within the box, and there is no concealed damage to the machine. If the package has suffered rough handling, bumps or damage (visible or concealed), please note it on the bill of lading before accepting the delivery and contact Omcan within 24 hours, so we may initiate a claim with the carrier. A detailed report on the extent of the damage caused to the machine must be

lled out within three days, from the delivery date shown in the shipping documents. Omcan has no recourse

for damaged products that were shipped collect or third party.

• Place the unit on a at, level surface.

• Do not place any ammable or explosive objects around the unit.

• Thoroughly read this manual before installing the unit.

Safety and Warranty

• Always keep the sealing platform clean. Leaving residue will reduce the life of the element, non-stick material and silicon rubber.

• Never use water to clean the sealing surface.

• Replace torn non-stick material immediately. A torn surface will short circuit the element and damage the

unit. Every time you replace the element, replace the lower and upper non-stick material.

• For best operation, use only genuine replacement parts.

• A worn silicon rubber will inuence the seal, change the silicon when worn or burned.

1 YEAR WARRANTY

WARNING:

The packaging components (cardboard, polyethylene, and others) are classied as normal solid urban waste and can therefore be disposed of without difculty.

3

Safety and Warranty

In any case, for suitable recycling, we suggest disposing of the products separately (differentiated waste) according to the current norms.

DO NOT DISCARD ANY PACKAGING MATERIALS IN THE ENVIRONMENT!

Technical Specications

Model Description Electrical Weight Packaging Dimensions

SE-CN-0203

SE-CN-0305

SE-CN-0406

SE-CN-0508

8” / 203mm seal bar

110V/60/1

0.2” / 5mm seal width 2.4 kg. 356 x 102 x 178mm 12” / 305mm seal bar

110V/60/1

0.2” / 5mm seal width 4 kg. 483 x 127 x 203mm 16” / 406mm seal bar

110V/60/1

0.2” / 5mm seal width 4.5 kg. 584 x 127 x 203mm 20” / 508mm seal bar

110V/60/1

0.2” / 5mm seal width 5.9 kg. 686 x 102 x 203mm

5.3 lbs. 14” x 4” x 7”

8.8 lbs. 19” x 5” x 8”

10 lbs. 23” x 5” x 8”

13 lbs. 27” x 4” x 8”

The unit features:

• Compact Design.

• Strong Water Tight Seal.

• Fast Operation.

• Precise Electric Circuit.

• Long Lasting.

MAIN COMPONENTS

1. Handle Knob.

2. Platen Arm.

3. Platen Spring.

4. Platen.

5. Silicon Rubber.

6. Swivel.

7. Hinge.

8. Hinge Bracket.

9. Enclosure.

10. Metal Plate.

11. Lower Element nonstick material.

12. Upper non-stick material Cloth.

13. Strain Relief Busing.

14. Power Supply Cord.

15. Heating Element.

16. Pilot Lamp.

17. Timer Knob.

18. Control Panel.

19. Variable Resistor.

20. Switch Level.

4

Operation

1. Plug the cord into a grounded outlet. You do not need to switch the machine on. The machine will operate only when the arm is down. Control the timer according to the thickness of the material to be sealed. Use a higher setting for thicker material. Pull the handle down to seal. Sealing takes place when the light it on. Leave the arm down for an additional few seconds after the light turns off to obtain a better seal.

2. Use a lower setting if the seal burns through.

3. Raise to a higher setting if the seal is not tight enough.

4. Should the bag stick to the silicon rubber, you did not give it enough time to cool.

5. Once you set the time, there is no need to reset it as the machine will remain constant and unchanged.

5

Parts Breakdown

Model SE-CN-0203 14446 Model SE-CN-0305 14448 Model SE-CN-0406 14450 Model SE-CN-0508 14451

6

Parts Breakdown

Model SE-CN-0203 14446 Model SE-CN-0305 14448 Model SE-CN-0406 14450 Model SE-CN-0508 14451

Description Position Description Position Description Position

Main Housing 1 Non-stick Cover Plate 9 Power Cord and Plug 18

Hand Lever 2 Pressure Bar Spring 10 Support Rail 19

Timer Assembly 3 Hand Lever Pin 11 Lever Hand Knob 20

Transformer 4 Hand Lever Bracket 12 Bottom Plate Housing 21

Pressure Bar 5 Tension - Element Spring 13 Rubber Foot 22

Rubber Pressure Bar 6 Fulcrum Lever 14 Pressure Bar Pin 23

Sealing Element (Band) 7 Lever Hand Spring 15 Non-stick Cover 24

Trim Element (Wire) 7 Micro Switch Bracket 16 Element Service Kit 25

Element Insulator 8 Micro Switch 17

7

Electrical Schematics

Model SE-CN-0203 14446 Model SE-CN-0305 14448 Model SE-CN-0406 14450 Model SE-CN-0508 14451

8

Notes

________________________________________________________________________________________

9

Notes

________________________________________________________________________________________

10

Warranty Registration

Thank you for purchasing an Omcan product. To register your warranty for this product, complete the information below, tear off the card at

the perforation and then send to the address specied below. You can also register online by visiting:

www.omcan.com/warrantyregistration.html

For mailing in Canada For mailing in the US

OMCAN INC.

PRODUCT WARRANTY REGISTRATION

3115 Pepper Mill Court,

Mississauga, Ontario

Canada, L5L 4X5

PRODUCT WARRANTY REGISTRATION

4450 Witmer Industrial Estates, Unit 4,

Niagara Falls, New York

OMCAN

USA, 14305



Purchaser’s Information

Name: Company Name:

Address:

Telephone:

City: Province or State: Postal or Zip: Email Address:

Country: Type of Company:

Restaurant Bakery Deli

Dealer from which Purchased: Butcher Supermarket Caterer

Dealer City: Dealer Province or State: Institution (specify):

Invoice: Other (specify):

Model Name: Model Number: Serial Number:

Machine Description:

Date of Purchase (MM/DD/YYYY): Date of Installation (MM/DD/YYYY):

Thank you for choosing Omcan

11

Over the last 65 years, Omcan has grown to become a leading supplier to the food service industry in Canada and the USA. Our success over these many years is directly attributed to our established relationships with all of our valued customers and through providing them with Diverse, Dependable and Proven products. Omcan continues to help our customers remain competitive.

With associates in North America, Europe, Asia, and South America, our global

footprint continues to expand as we hold to the principle that clients benet from

the accessibility and familiarity of our sales team. In 2013 as our geography and brand recognition continued to grow, we changed to one name Omcan Food Machinery.

In over 200,000 sq ft of warehouse space we stock over 2,500 quality food equipment and supplies for the food preparation market.

Omcan Food Machinery SE-CN-0203 Installation Manual

Specifications and Main Features

Frequently Asked Questions

User Manual