Omcan Food Machinery LAR-15PMB Installation Manual
Blenders
Models LAR-15PMB, LAR-25PMB
Instruction Manual
Version 1
3115 Pepper Mill Court, Mississauga, ON, L5L 4X5
4450 Witmer Industrial Estates, Unit 4, Niagara Falls, NY, 14305
1-800-465-0234
www.omcan.com
Table of Contents
Model LAR-15PMB / Model LAR-25PMB
Section
General Information
Safety and Warranty
Technical Specications
Installation
Operation
Maintenance
--------------------------------------------------------------------------------------- 5 - 6
----------------------------------------------------------------------------------------- 6 - 7
------------------------------------------------------------------------------------- 7 - 9
-------------------------------------------------------------------------------- 3
--------------------------------------------------------------------------- 3 - 4
Page
-------------------------------------------------------------------------- 5
Parts Breakdowns
Electrical Schematics
Warranty Registration
-------------------------------------------------------------------------- 10 - 13
---------------------------------------------------------------------- 14 - 15
---------------------------------------------------------------------------- 17
2
General Information
Omcan Manufacturing and Distributing Company Inc. and Food Machinery Of America, Inc. dba Omcan
are not responsible for any harm or injury caused due to any person’s improper or negligent use of
this equipment. The product shall only be operated by someone over the age of 18, of sound mind, and
not under the inuence of any drugs or alcohol, who has been trained in the correct operation of this
machine, and is wearing authorized, proper safety clothing. Any modication to the machine voids any
warranty, and may cause harm to individuals using the machine or in the vicinity of the machine while
in operation.
Safety and Warranty
The High Performance Tilting Blenders are simple to use and clean. However, for your safety read the
following instructions in order to avoid accidents:
1. Always unplug the machine when cleaning, servicing or when any other maintenance operation is needed.
2. Never use tools that do not belong to the machine during operation.
3. Never spray water on the machine.
4. Do not operate the machine while wearing wet clothes or wet shoes.
5. Before operating the machine, make sure it is properly grounded.
6. When washing inside of the Cup Nº02 (Pic. 01) ensure power is off and unit is unplugged. Be careful with
the blade as it has sharp edges.
General Safety Practices
The following safety instructions are addressed to both the operator of the machine as well as the person in
charge of maintenance. The user shall operate the machine only after being well acquainted with the safety
procedures described in the present manual. READ THIS MANUAL THOROUGHLY.
Basic Operation Practices
Dangerous parts
Some parts of the electric devices are connected to high voltage points. These parts when touched may cause
severe electrical shocks or can even be FATAL. Never touch commands such as buttons, switches and knobs
with wet hands, wet clothes and/or shoes. By not following these instructions, operators could be exposed to
severe electrical shocks or even to a FATAL situation.
3
Safety and Warranty
Warnings
The operator has to be well familiar with the position of ON/OFF Switch to make sure the Switch is easily
accessible when necessary. Before any kind of maintenance, physically remove plug from the socket. Provide
space for a comfortable operation thus avoiding accidents. Water or oil spilled on the oor will cause additional
hazards. Make sure the oor is clean and dry. Before giving any manual command (switch, buttons, turn keys
or lever) be sure the command is the correct one. Check this manual for further details if necessary. Never
use a manual command (switch, buttons, lever) unadvisedly. If any work is to be made by two or more people,
coordination signs will have to be given for each operation step. Every step of the operation shall be taken only
if the sign has been made and responded.
Advices
In case of power shortage, immediately turn the machine OFF. Use recommended or equivalent lubricants, oils
or greases. Avoid mechanical shocks as they may cause failures or malfunction. Avoid penetration of water,
dirt or dust into mechanical or electrical components of the machine. DO NOT MODIFY original characteristics
of the machine. DO NOT REMOVE, TEAR OFF or MACULATE ANY SAFETY or IDENTIFICATION LABELS
stuck on the machine. If any label has been removed or is no longer legible, contact your nearest dealer for
replacement.
Safety Procedures and Notes Before Switching Machine ON
IMPORTANT: Carefully read ALL INSTRUCTIONS of this manual before turning the machine ON. Be
sure to be familiar with the instructions and that you have understood all information contained in this
manual. If you have any questions contact your supervisor or your nearest Dealer.
Danger
An electric cable or electric wire with damaged jacket or bad insulation could cause electrical shocks as well as
electrical leak. Before use, unplug and check conditions of all wires and cables.
Advices
Be sure ALL INSTRUCTIONS in this manual have been thoroughly understood. Every function and operational
procedure have to be very clear to the operator. Contact your nearest Dealer for further questions. Any manual
command (switch, button or lever) shall be given only after being sure it is the correct one.
Precautions
The electric cable has to be compatible with the power required by the machine. Cables touching the oor or
close to the machine need to be protected against short circuits.
4
Technical Specications
Main Components
All components are made with carefully selected materials, in accordance with Omcan experience and
standard testing procedures.
01- Lid
02- Cup
03- On/Off Switch
04- Voltage Selector Switch 110/220V
05- Stand
06- Motor
07- Lock Pedal
Picture 1
Technical Data Units LAR-15PMB LAR-25PMB
Voltage [V] 110/220 110/220
Power Rating [Hz] 50 or 60 50 or 60
Frequency [CV] 1,0 1,0 or 1.5
Consuption [kW/h] 0,73 0,73 or 1,1
Height [mm] 1060 1180
Width [mm] 360 410
Depth [mm] 525 525
Net Weigth [kg] 19 20,5
Gross Weigth [kg] 23 24
Rotation [ rpm] 3500 3500
(*) Frequency will be only the one indicated on motor characteristics label.
Installation
The High Performance Tilting Blenders were developed to be used in both voltages: 110V or 220V. Upon
receiving the Blender adjust its voltage according to the one of the power supply source using the Voltage
Selector Switch Nº04 (Pic. 01) located at the bottom of the machine. Adjust it if necessary. Grounding is
mandatory.
5
Installation
Pre Operation
First of all check if the Blender is rm on its position. Check if Motor (Nº01) is perfectly tted on the Lock Pedal
(Nº02) as shown on Picture 2.
01 - Motor
02 - Pedal Lock.
Picture 2
IMPORTANT: Before doing any maintenance to the machine switch it OFF and unplug it.
Operation
Starting
The Blender is activated by turning the On/Off Switch Nº03 (Pic.01) to ON position.
Operating Procedures
The High Performance Tilting Blender works at high speed (approximately 3.500 rpm, 50Hz). To feed it
proceed as follows:
1. Remove the Lid Nº01 (Pic.01).
2. Put product inside the Cup Nº02 (Pic.01) with the machine switched OFF.
3. Place the Lid Nº01 (Pic.01) back on top of the Cup and switch the machine ON.
NOTE: Due to turbulence generated when machine is ON do not turn it ON without the Lid Nº01
(Pic.01). The processing time depends on the kind of product.
IMPORTANT: NEVER SWITCH THE MACHINE ON WITHOUT PRODUCT IN IT BECAUSE IT WILL CAUSE
IRREPARABLE DAMAGES.
IMPORTANT: It is not recommended to blend products without the addition of any liquid, otherwise it
will overheat and damage the Cup seal.
6
Loading...