22492.8Maio/2008
Models:
LAR-15/25
Instruction Manual
SUMMARY
2
2
2
3
3
3
6
6
7
8
8
9
9
8
4
4
4
5
5
Instructions Manual
1. Introduction
1.1 Safety
1.2 Main Components
1.3 Technical Characteristics
2. Installation and Pre operation
2.1 Installation
2.2 Pre operation
3. Operation
3.1 Starting
3.2 Operating Procedures
3.3 Discharging Procedures
3.4 Cleaning
4. General Safety Practices
4.1 Basic Operation Procedures
4.2 Safety Procedures and Notes Before Switching the
Machine On
4.3 Routine Inspection
4.4 Operation
4.5 After Finishing the Work
4.6 Maintenance Operation
5. Analysis and Problem Solving
5.1 Problems, Causes and Solutions
5.2 Electric Diagram - LAR-15/25
3
9
10
ON/OFF Switch
Voltage Selector Switch
110/220V
5.2 Electric Diagram Mod. LAR-15/25
10
01
1. Introduction
1.1 Safety
The High Performance Tilting Blenders Models LAR-15/25 are
machines simple to use and to clean. However for your safety read the
following instructions in order to avoid accidents:
1.1.1 Always unplug the machine when cleaning, servicing or when
any other operation is needed.
1.1.2 Never use tools that do not belong to the machine during
operation.
1.1.3 Never throw water directly to the machine.
1.1.4 Do not operate the machine wearing wet clothes or wet shoes.
1.1.5 Before operating the machine be sure it is grounded properly.
1.1.6 When washing inside the Cup Nº02 (Pic. 01) be careful with
the blade as it has sharp edges.
1.2 Main Components
All components are made with carefully selected materials, in
accordance with Siemsen experience and standard testing procedures.
Picture 1
01- Lid
02- Cup
03- On/Off Switch
04- Voltage Selector Switch 110/220V
05- Stand
06- Motor
07- Lock Pedal
02
01
03
04
06
03
05
07
02
09
4.6 Maintenance
4.6.1 Danger
Any maintenance with the machine in working situation is
dangerous. TURN IT OFF BY PULLING THE PLUG OFF THE SOCKET
DURING MAINTENANCE.
IMPORTANT
Always unplug the machine when emergency cases arise.
4.6 Advice
Electrical or mechanical maintenance must be done by qualified
personal for such operation.
Person in charge has to be sure that the machine is under TOTAL
SAFETY conditions when working.
5 Analysis and Problems Solving
5.1 Problems, causes and solutions
The High Performance Tilting Blenders were designed to operate
with the need of minimum maintenance but the natural wearing caused
by long use of the equipment may occasionally cause some malfunctions.
If such problem occurs with your Blender refer to Table 02 in which
the most common situations are listed with recommended solutions.
Table - 02
Problems Causes Solutions
*Lack of power.
* Problem in the electric circuit
of the machine.
* Check if machine is
plugged in and if there is
power in the power supply
source.
* The machine does not turn
on..
* Cup is leaking. * Damaged seal.
* Call technical assistance.
* Call technical assistance.
03
1.3 Technical Characteristcs
(*) Frequency will be only the one indicatedon motor characteristics label.
TABLE - 01
LAR-15
LAR-25
110/220(*) 110/220(*)
50 or 60 50 or 60
1,5 1,5
1,1 1,1
1070 1200
300 350
600 600
20 22
[V]
[Hz]
[CV]
[kW/h]
[mm]
[mm]
[mm]
[kg]
[kg]
22 25
Technical Data
Units
Voltage
Power Rating
Frequency
Consuption
Height
Width
Depth
Net Weigth
Gross Weigth
2. Installation and Pre Operation
2.1 Installation
The High Performance Tilting Blenders were developed to be
used in both voltages: 110V or 220V. Upon receiving the Blender adjust
its voltage according to the one of the power supply source using the
Voltage Selector Switch Nº04 (Pic. 01) located at the bottom of the
machine. Adjust it if necessary.
Grounding is mandatory.
2.2 Pre Operation
First of all check if the Blender is firm on its position. Check if
Motor (Nº01) is perfectly fitted on the Lock Pedal (Nº02) as shown on
the Picture below.
08
4.3 Routine Inspection
4.3.1 Advice
When checking the tension of the belts or chains, DO NOT
introduce your fingers between the belts and the pulleys and nor
between the chain and the gears.
4.3.2 Precautions
Check if motors and sliding or turning parts of the machine produce
abnormal noises.
Check the tension of the belts and chains and replace the set when
belt or chain show signs of being worn out.
When checking tensions of belts or chain DO NOT introduce your
fingers between belts and pulleys, nor between the chains and gears.
Check protections and safety devices to make sure they are working
properly.
4.4 Operation
4.4.1 Advice
Be sure your hair is not loose in order to avoid getting caught by
turning parts which could lead to a serious accident. Tie your hair well up
and/or cover your head with a scarf.
The operation performed by not trained or skilled personnel shall be
forbidden.
Never touch turning parts with your hands or in any other way.
NEVER operate machine without all original safety devices under
perfect conditions.
4.5 After Finishing The Work
4.5.1 Precautions
Always TURN THE MACHINE OFF by removing the plug from the
socket before cleaning the machine.
Never clean the machine unless it has come to a COMPLETE
STOP.
Put all components back to their functional positions before
turning it ON again. DO NOT place your fingers in between belts and
pulleys nor chains and gears.
07
4.1.3 Advices
In case of power shortage, immediately turn the machine OFF.
Use recommended or equivalent lubricants, oils or greases.
Avoid mechanical shocks as they may cause failures or malfunction.
Avoid penetration of water, dirt or dust into mechanical or electrical
components of the machine.
DO NOT MODIFY original characteristics of the machine.
DO NOT REMOVE, TEAR OFF or MACULATE ANY SAFETY or
IDENTIFICATION LABELS stuck on the machine. If any label has been
removed or is no longer legible, contact your nearest dealer for
replacement.
4.2 Safety Procedures and Notes Before Switching Machine ON
IMPORTANT
Carefully read ALL INSTRUCTIONS of this manual before turning
the machine ON. Be sure to be familiar with the instructions and
that you have well understood all information contained in this
manual. If you have any question contact your supervisor or your
nearest Dealer.
4.2.1 Danger
An electric cable or electric wire with damaged jacket or bad
insulation could cause electrical shocks as well as electrical leak. Before
use, check conditions of all wires and cables.
4.2.2 Advices
Be sure ALL INSTRUCTIONS in this manual have been thoroughly
understood. Every function and operational procedure have to be very
clear to the operator. Contact your nearest Dealer for further questions.
Any manual command (switch, button or lever) shall be given only
after being sure it is the correct one.
4.2.3 Precautions
The electric cable has to be compatible with the power required
by the machine. Cables touching the floor or close to the machine need
to be protected against short circuits.
01
02
01 - Motor
02 - Pedal Lock.
Picture -02
IMPORTANT
Before doing any maintenance in the machine switch it OFF and
unplug it.
3. Operation
3.1 Starting
The Blender is activated by turning the On/Off Switch Nº03
(Pic.01) to ON position.
3.2 Operating Procedures
The High Performance Tilting Blender works at high speed
(approximately 3.500 rpm, 50Hz). To feed it proceed as follows:
1 – Remove the Lid Nº01 (Pic.01).
2 – Put product inside the Cup Nº02 (Pic.01) with the machine
switched OFF.
3 – Place the Lid Nº01 (Pic.01) back on top of the Cup and
switch the machine ON.
04
05
NOTE
Due to turbulence generated when machine is ON do not turn it ON
without the Lid Nº01 (Pic.01). The processing time depends on the
kind of product.
IMPORTANT
NEVER SWITCH THE MACHINE ON WITHOUT LOAD IN IT
BECAUSE IT WILL CAUSE IRREPARABLE DAMAGES.
IMPORTANT
It is not recommended to blend products without the addition of
any liquid, otherwise it will overheat and damage the Cup seal.
3.3 Discharging Procedures
To discharge processed product from Blender Models LAR-15/25
proceed as follows:
1- Turn machine OFF.
2- Remove Lid Nº01 (Pic. 01).
3- Press Lock Pedal Nº07 (Pic. 01) down.
4- Tilt Cup Nº02 (Pic. 01) holding its handle and discharge
processed product as needed.
3.4 Cleaning
The new Blenders cup has stamped ribs that facilitate cleaning.
Wash the Lid Nº01 and the Cup Nº02 (Pic. 01) with water and neutral
soap. Wipe up the other parts with a damp cloth.
IMPORTANT
Never do cleaning with machine plugged in. Always unplug
machine before cleaning. When washing inside the Cup be careful
with the blade.
06
4. General Safety Practices
The following safety instructions are addressed to both the operator
of the machine as well as the person in charge of maintenance. The
machine has to be delivered to the operator in perfect conditions of use by
the Distributor to the user. The user shall operate the machine only after
being well acquainted with the safety procedures described in the present
manual. READ THIS MANUAL WITH ATTENTION.
4.1 Basic Operation Practices
4.1.1 Dangerous parts
Some parts of the electric devices are connected to high voltage
points. These parts when touched may cause severe electrical shocks or
even be FATAL.
Never touch commands such as buttons, switches and knobs with
wet hands, wet clothes and/or shoes. By not following these instructions
operator could be exposed to severe electrical shocks or even to a FATAL
situation.
4.1.2 Warnings
The operator has to be well familiar with the position of ON/OFF
Switch to make sure the Switch is easy to be reached when necessary.
Before any kind of maintenance, physically remove plug from the socket.
Provide space for a comfortable operation thus avoiding accidents.
Water or oil spilled on the floor will turn it slippery and dangerous. Make
sure the floor is clean and dry.
Before giving any manual command (switch, buttons, turn keys or
lever) be sure the command is the correct one. Check this manual for
further details if necessary.
Never use a manual command (switch, buttons, lever) unadvisedly.
If any work is to be made by two or more persons, coordination signs will
have to be given for each operation step. Every step of the operation shall
be taken only if the sign has been made and responded.
Loading...