Omcan Food Machinery FP-IT-0320 Installation Manual

Food Processor

Model FP-IT-0320

Instruction Manual

Revised - 9/9/2014

Toll Free: 1-800-465-0234

Fax: [phone]

Email: [e-mail]

www.omcan.com

Table of Contents

Model FP-IT-0320

Section

General Information

Safety and Warranty

Technical Specications

Installation

Operation

Maintenance

---------------------------------------------------------------------------------------------- 3

---------------------------------------------------------------------------------------------- 3 - 5

---------------------------------------------------------------------------------------------- 5

---------------------------------------------------------------------------------------------- 6 - 7

---------------------------------------------------------------------------------------------- 7 - 10

---------------------------------------------------------------------------------------------- 10

Page

---------------------------------------------------------------------------------------------- 11 - 12

Parts Breakdowns

Electrical Schematics

Notes

Warranty Registration

---------------------------------------------------------------------------------------------- 13

---------------------------------------------------------------------------------------------- 14

---------------------------------------------------------------------------------------------- 15

2

General Information

Omcan Manufacturing and Distributing Company Inc. and Food Machinery of America, Inc. dba Omcan
are not responsible for any harm or injury caused due to any person’s improper or negligent use of
this equipment. The product shall only be operated by someone over the age of 18, of sound mind, and

not under the inuence of any drugs or alcohol, who has been trained in the correct operation of this
machine, and is wearing authorized, proper safety clothing. Any modication to the machine voids any
warranty, and may cause harm to individuals using the machine or in the vicinity of the machine while

in operation.

All routine and extraordinary maintenance operations of the machine must only be carried out by trained
personnel. This manual is an integral part of the machine and must accompany the unit for its whole lifetime
until demolition. We recommend you read these Instructions carefully before performing any installation,
operation or maintenance. All operators attending the machine must know the directions contained in the
instruction manual. Hand over this manual to any other user or successive owner of the machine. Omcan
cannot be held responsible for drawbacks, breakdowns, accidents, etc. as a result of the lack of knowledge or

non-application of the rules contained in this manual. The same is true for any change, modication and/or for

the installation of non-authorised parts.

CHECK PACKAGE UPON ARRIVAL

Upon receipt of an Omcan shipment please inspect for external damage. If no damage is evident on the
external packaging, open carton to ensure all ordered items are within the box, and there is no concealed
damage to the machine. If the package has suffered rough handling, bumps or damage (visible or concealed),
please note it on the bill of lading before accepting the delivery and contact Omcan within 24 hours, so we may
initiate a claim with the carrier. A detailed report on the extent of the damage caused to the machine must be

lled out within three days, from the delivery date shown in the shipping documents. Omcan has no recourse

for damaged products that were shipped collect or third party.

Safety and Warranty

Before starting working with the machine the operator must be perfectly aware of the position and the working
of all the controls and of the characteristics of the machine described in this manual. Never tamper with the
safety devices. Never remove, nor change the protections and safety devices, especially those installed
at the meat inlet. Never tamper with the electric system. Always disconnect from power supply before
performing any cleaning, servicing or maintenance operation. The use of the machine in environments with
hazardous surroundings is forbidden. The working position is in front of the start & stop push buttons. Never
go near the machine with loose hair, clothes, bracelets, chains, rings, ties, etc. to avoid the chance that they
become tangled in the moving parts of the machine. The operator shall wear suitable clothes for the working
environment. Always keep the working place clear and free from oil residues. The room where the machine

is installed must not have dark areas, ickering lights, or a faulty lighting system. Make sure that the voltage
of the outlet is the same as the voltage required by the machine (see the rating plate). Any modication to the

machine must be authorised by Omcan. Never spray with high pressure water to clean the machine. Warning:
the voltage inside the machine is 110V.

3

Safety and Warranty

Always use original replacement parts that guarantee the perfect
working and the safety of the machine. The electric cable must be
checked regularly and carefully (a worn cable or a cable in less than
perfect condition is always a serious electrical danger).

WARNING SIGNALS

“WARNING” adhesive labels are placed on the machine. They must

be replaced with the labels supplied when it becomes difcult to

read them. Read these labels before operating the machine. (FIG. A.
describes their position on the machine).

Safety devices and protections: The picture below shows all the
protections and safety devices installed on the machine. Safety
magnetic sensors stopping the cycle when cover is opened and lever
is released.(Fig. B).

NEVER TAMPER WITH THE MECHANICAL SAFETY
PROTECTIONS WITH BLUNT OBJECTS (SCREWDRIVERS,
KNIVES, ETC.) TO TRY TO ACCESS MOVING PARTS INSIDE THE
MACHINE. DO NOT TURN OR TAMPER THE MAGNETIC SENSOR
(FIG. B).

Fig. A

Fig. B

1 YEAR PARTS AND LABOR WARRANTY

WARNING:

The packaging components (cardboard, polyethylene, and others) are classied as normal solid urban waste

4

Safety and Warranty

and can therefore be disposed of without difculty.

In any case, for suitable recycling, we suggest disposing of the products separately (differentiated
waste) according to the current norms.

DO NOT DISCARD ANY PACKAGING MATERIALS IN THE ENVIRONMENT!

Technical Specications

RECOMMENDED USE

The machine is designed to process vegetables (with the exception of leafy vegetables) and fresh cheeses.
Different cutting disks may be used according to the type of processing desired. In addition, the machine can
grate: bread, nuts, chocolate, ripened cheeses etc. Any use different from the recommended should not be
considered and may be dangerous for the machine and the Operator. Always and only use the attachments
supplied. The machine must always be operated by only one operator. The working and control position of the
operator is in front of the machine.

OPERATING RANGES

The proper function of the machine is guaranteed within the following environmental ranges:

Temperature range between +5°C/+41°F and +45°C/+113°F.
Humidity range between 30% and 90%.

AFTER-SALES SERVICE

It is recommended that you contact Omcan for all the servicing and maintenance operations that are not
described in these Operating Instructions.

Horsepower 1 HP
Disc Speed 320 RPM

Mouth Opening 7 ¾” x 3 ⅛” / 197mm x 79mm

Electrical 110V/60/1
Weight 48.5 lbs. / 22 kg.
Dimension (DWH) 24” x 9 ¼” x 21” / 610mm x 235mm x 533mm

5