Page 1
Gear-Driven Slicer
Model MS-IT-0350-H
Item 39631
Instruction Manual
Revised - 08/02/2018
Toll Free: 1-800-465-0234
Fax: 905-607-0234
Email: service@omcan.com
www.omcan.com
Page 2
Table of Contents
Model MS-IT-0350-H
Section
General Information
Safety and Warranty
Technical Specications
Installation
Operation
Maintenance
--------------------------------------------------------------------------------------- 6 - 7
--------------------------------------------------------------------------------------------- 7
----------------------------------------------------------------------------------- 8 - 10
--------------------------------------------------------------------------- 3 - 4
--------------------------------------------------------------------------- 4 - 5
Page
-------------------------------------------------------------------------- 6
Troubleshooting
Parts Breakdown
Electrical Schematics
Warranty Registration
----------------------------------------------------------------------------------- 11
---------------------------------------------------------------------------- 12 - 25
---------------------------------------------------------------------------- 26
--------------------------------------------------------------------------- 27
2
Page 3
General Information
Omcan Manufacturing and Distributing Company Inc., Food Machinery of America, Inc. dba Omcan
and Omcan Inc. are not responsible for any harm or injury caused due to any person’s improper or
negligent use of this equipment. The product shall only be operated by someone over the age of 18, of
sound mind, and not under the inuence of any drugs or alcohol, who has been trained in the correct
operation of this machine, and is wearing authorized, proper safety clothing. Any modication to the
machine voids any warranty, and may cause harm to individuals using the machine or in the vicinity of
the machine while in operation.
CHECK PACKAGE UPON ARRIVAL
Upon receipt of an Omcan shipment please inspect for external damage. If no damage is evident on the
external packaging, open carton to ensure all ordered items are within the box, and there is no concealed
damage to the machine. If the package has suffered rough handling, bumps or damage (visible or concealed),
please note it on the bill of lading before accepting the delivery and contact Omcan within 24 hours, so we may
initiate a claim with the carrier. A detailed report on the extent of the damage caused to the machine must be
lled out within three days, from the delivery date shown in the shipping documents. Omcan has no recourse
for damaged products that were shipped collect or third party.
Before operating any equipment, always read and familiarize yourself with all operation and safety
instructions.
Omcan would like to thank you for purchasing this machine. It’s of the utmost importance to save
these instructions for future reference. Also save the original box and packaging for shipping the
equipment if servicing or returning of the machine is required.
--------------------------------------------------------------------------------------------------------------------------------------------------Omcan Fabrication et distribution Companie Limité et Food Machinery d’Amerique, dba Omcan et
Omcan Inc. ne sont pas responsables de tout dommage ou blessure causé du fait que toute personne
ait utilisé cet équipement de façon irrégulière. Le produit ne doit être exploité que par quelqu’un de
plus de 18 ans, saine d’esprit, et pas sous l’inuence d’une drogue ou d’acohol, qui a été formé pour
utiliser cette machine correctement, et est vêtu de vêtements de sécurité approprié. Toute modication
de la machine annule toute garantie, et peut causer un préjudice à des personnes utilisant la machine
ou des personnes à proximité de la machine pendant son fonctionnement.
VÉRIFIEZ LE COLIS DÈS RÉCEPTION
Dès réception d’une expédition d’Omcan veuillez inspecter pour dommages externes. Si aucun dommage
n’est visible sur l’emballage externe, ouvrez le carton an de s’assurer que tous les éléments commandés
sont dans la boîte, et il n’y a aucun dommage dissimulé à la machine. Si le colis n’a subi aucune mauvaises
manipulations, de bosses ou de dommages (visible ou cachée), notez-le sur le bond de livraison avant
d’accepter la livraison et contactez Omcan dans les 24 heures qui suivent, pour que nous puissions engager
une réclamation auprès du transporteur. Un rapport détaillé sur l’étendue des dommages causés à la machine
doit être rempli dans un délai de trois jours, à compter de la date de livraison indiquée dans les documents
d’expédition. Omcan n’a aucun droit de recours pour les produits endommagés qui ont été expédiées ou cueilli
par un tiers transporteur.
3
Page 4
General Information
Avant d’utiliser n’importe quel équipement, toujours lire et vous familiariser avec toutes les opérations
et les consignes de sécurité.
Omcan voudrais vous remercier d’avoir choisi cette machine. Il est primordial de conserver ces
instructions pour une référence ultérieure. Également conservez la boîte originale et l’emballage pour
l’expédition de l’équipement si l’entretien ou le retour de la machine est nécessaire.
--------------------------------------------------------------------------------------------------------------------------------------------------Omcan Empresa De Fabricacion Y Distribucion Inc. Y Maquinaria De Alimentos De America, Inc. dba
Omcan y Omcan Inc. no son responsables de ningun daño o perjuicío causado por cualquier persona
inadecuada o el uso descuidado de este equipo. El producto solo podra ser operado por una persona
mayor de 18 años, en su sano juicio y no bajo alguna inuencia de droga o alcohol, y que este ha sido
entrenado en el correcto funcionamiento de esta máquina, y ésta usando ropa apropiada y autorizada.
Cualquier modicación a la máquina anúla la garantía y puede causar daños a las personas usando la
máquina mientras esta en el funcionamiento.
REVISE EL PAQUETE A SU LLEGADA
Tras la recepcion de un envio Omcan favor inspeccionar daños externos. Si no hay daños evidentes en el
empaque exterior, Habra el carton para asegurararse que todos los articulos solicitados ésten dentro de la
caja y no encuentre daños ocultos en la máquina. Si el paquete ha sufrido un manejo de poco cuidado, golpes
o daños (visible o oculto) por favor anote en la factura antes de aceptar la entrega y contacte Omcan dentro
de las 24 horas, de modo que podamos iniciar una reclamación con la compañia. Un informe detallado sobre
los daños causados a la máquina debe ser llenado en el plazo de tres días, desde la fecha de entrega que se
muestra en los documentos de envío. Omcan no tiene ningun recurso por productos dañados que se enviaron
a recoger por terceros.
Antes de utilizar cualquier equipo, siempre leer y familiarizarse con todas las instrucciones de
operación y seguridad.
Omcan quisiera darles las gracias por la compra de esta máquina. Es de la máxima importancia para
guardar estas instrucciones para referencias en el futuro. También guarde la caja original y el embalaje
para envío del equipo si el mantenimiento o la devolución de la máquina es necesaria.
Safety and Warranty
MECHANICAL SAFETY DEVICES
The slicer is manufactured according to the EEC 2006/42 Machinery Directive.
The mechanical safety devices are the following:
• Product holder removable only with the slice thickness control on zero (slice thickness plate positioned to
protect the blade). After removing the product holder the slice thickness plate is mechanically clamped.
4
Page 5
Safety and Warranty
• Protection devices mounted on the product holder to prevent the operator from any accidental contact with
the blade.
• Blade guard. This xed ring protects that part of the blade which is not used for the cutting operation.
• A special mechanical safety device to sharpen the blade keeping the ngers of the operator away from the
cutting edge of the blade.
ELECTRICAL SAFETY DEVICES
The electrical safety devices in accordance with the EN 60204 standards are the following:
• Start and stop push buttons.
• Control circuit provided with electric servo-control; in any case of blade clamping the machine must be
restarted manually.
• Safety device to stop the rotation of the blade if the clamping handle of the blade guard is released.
WARNING
When the machine is not used:
• Make sure that it is off.
• Re-position the slice thickness control to zero.
Do not remove the labels placed on the machine and replace them if damaged.
1 YEAR PARTS AND LABOUR WARRANTY
Within the warranty period, contact Omcan Inc. at 1-800-465-0234 to schedule an Omcan authorized
service technician to repair the equipment locally.
Unauthorized maintenance will void the warranty. Warranty covers electrical and part failures, not
improper use.
Please see www.omcan.com/warranty.html for complete info.
WARNING:
The packaging components are classied as normal solid urban waste and can therefore be disposed of
without difculty.
In any case, for suitable recycling, we suggest disposing of the products separately (differentiated
waste) according to the current norms.
DO NOT DISCARD ANY PACKAGING MATERIALS IN THE ENVIRONMENT!
5
Page 6
Technical Specications
Model MS-IT-0350-H
Blade Size 14” / 350mm
Power 0.4 HP / 0.3 kW
Cheese Slicing
Slicing Volume* 8 hours or more
RPM 250
Cutting Size 12.2” x 9.8” / 310 x 250mm
Cut Thickness 0” - 1” / 0 - 25mm
Electrical 110V/60/1
Weight 110 lbs. / 50 kgs.
Dimensions 26.4” x 28” x 21.7” / 670 x 710 x 550mm
Item Number 39631
*Results may vary due to product consistency and temperature
Installation
The slicer must be mounted horizontally on a stable, robust and antiskid base adequate to support its weight.
The suggested height of the working table is of about 800mm. It must be checked that the product holder is not
clamped and the product to be cut can be easily loaded.
WARNING: To prevent the risk of crushing hazard, locate the machine in a manner that allows a clear space
between the moving table and any permanent structure.
PRELIMINARY CLEANING
Before connecting the plug clean off the protective oil from the machine.
WARNING
The working table must always be cleaned.
ELECTRICAL SUPPLY
The machine must be installed in the proximity of a mains socket. Check that the power supply voltage
corresponds to that described on the information label and that it is connected to an adequate earth.
1. Connect the plug.
2. Check that the blade cover fastener handle is tight screwed.
3. Check that the blade sharpener is lowered and the protective cover is closed.
MANUAL FUNCTIONING
1. Press push button blade start.
6
Page 7
Installation
SLICER FUNCTIONING AND USE
The following products can be sliced: sausages, ham, cheese, bread. If large quantities of bread or cheese are
usually cut it is advisable to mount a teon coating.
WARNING
The following cannot be sliced:
• Not-eatable products.
• Foodstuffs with bones.
• Frozen products.
MANUAL FUNCTIONING
Rotate the product holder release handle in a clockwise direction by 180°.
Operation
HOW TO LOAD THE PRODUCT TO BE CUT
1. Check that the slicer is off and position the slice thickness control to zero.
2. Push the product holder towards the operator.
3. Lift and rotate the product pusher: the pusher can fall back, this is normal.
4. Place the product to be cut against the wall of the product holder and the slice thickness plate.
5. Position the product pusher on the product to be cut far from the slice thickness plate. The product is fed to
the slice thickness plate by gravity making the cut easier.
6. Rotate the slice thickness control to the thickness desired.
DANGER
Do not touch the carriage or the product holder when the machine is working.
MANUAL FUNCTIONING
1. Rotate the carriage release handle in a clockwise direction by 180°.
2. Press push button to start the blade.
3. With constant speed, according to the product to be sliced features, you can push the product holder tray
to its end stroke in blade direction. You can then return in the operator position and repeat this operation.
After cutting the product, reposition the product holder towards the operator. By pressing push button stop
blade the rotation of the blade stops. Re-position the slice thickness control to zero and unload the product.
7
Page 8
Maintenance
BLADE SHARPENING
Whenever the cut is not satisfactory, sharpen the blade. The time interval between a sharpening and the
following depends on the intensity of use of the slicer and on the kind of food you cut. Replace the blade when
the diameter becomes 10mm less than the nominal diameter. For the replacement, ask the assistant service
closest to you.
WARNING
The replacement of the blade is dangerous operation. Should the sharpening quality be not
satisfactory, replace the stones by contacting Omcan.
SHARPENING OPERATION
DANGER
The sharpening operation must be performed during the manual functioning.
For a correct sharpening of the blade follow these instructions:
1. Clean the blade removing any greasy residue.
2. Make sure that the machine is off.
3. Rotate the slice thickness control to zero to make sure that the blade is covered by the slice thickness
plate.
IMPORTANT
During the following operations the blade must always be covered by the removable protection.
4. Lift the sharpener cover.
5. Slip off completely the sharpener and spin it 180 degrees.
6. Replace the sharpener device.
7. Push the push button blade start to start the machine.
8. Sharpening: Press the sharpening wheel for about 10-15 seconds.
Then press simultaneously also the grinding stone for two seconds.
Contemporaneously loosen the two grind stones.
The sharpening and honing take place then simultaneously.
ATTENTION: for a suitable effect please execute sharpening for 10-15 seconds approx.
9. After sharpening press the blade stop push button.
10. Lift and rotate 180 degrees the sharpener and reallocate it into its initial position. Loosen the handle
rotating it clockwise to block the sharpener. Lower the sharpener cover.
CLEANING OF THE GRINDING WHEELS
To obtain an excellent sharpening the grinding wheel must always be clean. Remove dirt and grease with
alcohol and the supplied special brush. Be sure to clean and sanitize the blade after sharpening.
8
Page 9
Maintenance
MAINTENANCE
All cleaning and maintenance operations must only be carried out with the machine disconnected and isolated
from the mains supply and the slice thickness control on zero.
CONTROL OF THE AIR GRATING
An air grating for the motors ventilation is placed in the lower side of the machine. Keep the section-holes free
and clean them with a brush at regular intervals.
CHECK OF THE ELECTRIC CABLE
It is recommended to check the wear of the electric cable at regular intervals.
SPARE PARTS
In the event that replacement parts need to be tted, request only original spare parts.
CLEANING
The machine must be cleaned once a day or more frequently if necessary. Clean all the parts using a cloth
sprinkled with water and washing up liquid (do not use strong detergents) and a brush.
WARNING
Do not use water jet
DANGER
During the cleaning operations take great care: danger of accident.
COMPONENTS REMOVAL
PRODUCT HOLDER
1. Loose the product holder by rotating the product holder clamping handle in a counterclockwise direction.
2. Position to zero the slice thickness control to remove the product holder.
3. Push the product holder towards the operator until it clicks. The click will inform the operator that the
product holder is clamped.
4. Lift the last slice device from the guide bar.
5. Lift the product holder from the carriage.
IMPORTANT
The slice thickness control is clamped on zero.
9
Page 10
Maintenance
BLADE COVER
1. Rotate the slice deector and keep it away from the blade.
2. Loose the blade cover fastener handle by rotating it in a counterclockwise direction.
3. Push on the handle in the direction indicated by the arrow to lift the blade cover from the blade.
4. Lift the blade cover.
ATTENTION
Once removed the blade cover, an interlocking device stops the rotation of the blade.
DANGER
During the cleaning operations of the blade, pay attention to an accidental contact with it.
5. Press a damp cloth on the front side of the blade and move slowly from the center towards the edge in the
direction of the arrow.
6. Follow these instructions to clean the back side of the blade.
7. With a cloth dry both sides of the blade following this procedure.
8. Insert a damp cloth between the blade and the protection ring. Pull it outwards and rotate it to clean the
internal side of the protection ring.
9. After cleaning re-position the blade cover, insert the fastener and screw in a clockwise direction to clamp
the blade cover. Lower the sharpener protective cover.
IMPORTANT
Leave all the parts to soak in warm water and washing-up liquid (do not use strong detergents) and clean them
by using a brush or a cloth. Rinse them in warm water and dry them.
To assemble the machine follow the reverse procedure as described for disassembly.
GUIDES LUBRICATION
This operation must be performed after cleaning the slicer or whenever the sliding is difcult. Use food safe oil
only.
LUBRICATION OF THE GUIDE BAR OF THE LAST SLICE DEVICE
1. Drop some food grade oil on the bar.
2. Let the last slice device slide on the guide bar.
LUBRICATION OF THE GUIDE BAR OF THE PRODUCT HOLDER CARRIAGE
1. Push the product holder towards the operator.
2. Pour the food grade lubricating oil into the special carriage bar lubricator.
3. Push the product holder to and from and repeat the operation. Re-position it towards the operator.
10
Page 11
Troubleshooting
PROBLEM CORRECTIVE ACTION
The machine vibrates, overheats
and emits a foul smell.
The blade cannot be sharpened
any longer. The sharpening is no
regular.
On pushing the start push button
the machine does not start.
The carriage and the last slice
device run with difculty.
REFERENCE
Item Number Model Number Description Manufacturer Model Number
39631 MS-IT-0350-H
Stop it immediately and check that the voltage corresponds to that described on the rating label.
Clean the grinding wheels of the sharpener and check the wear of the
blade.
Check if power missing. Check the safety devices.
Lubricate the guide bars.
Meat Slicer Gear Driven 14” / 350mm
Blade with Fixed Ring Knife Guard
0.4HP / 300W 110V/60/1 CSST
H35S
11
Page 12
Parts Breakdown
Model MS-IT-0350-H 39631
12
Page 13
Model MS-IT-0350-H 39631
Parts Breakdown
13
Page 14
Parts Breakdown
Model MS-IT-0350-H 39631
14
Page 15
Model MS-IT-0350-H 39631
Parts Breakdown
15
Page 16
Parts Breakdown
Model MS-IT-0350-H 39631
16
Page 17
Model MS-IT-0350-H 39631
Parts Breakdown
17
Page 18
Parts Breakdown
Model MS-IT-0350-H 39631
18
Page 19
Model MS-IT-0350-H 39631
Parts Breakdown
19
Page 20
Parts Breakdown
Model MS-IT-0350-H 39631
20
Page 21
Model MS-IT-0350-H 39631
Parts Breakdown
21
Page 22
Parts Breakdown
Model MS-IT-0350-H 39631
Item No. Description Position Item No. Description Position Item No. Description Position
77583 Sharpener (Support+Stones) for H35S A1024 17312 Bushing 22x25x20 for H35S B6211 17335 Bear.2RS-6203 17x40x12 for H35S C8022
36532 Sharpener Assembly for H35S A1025 36563 Carriage Bushing for H35S B6213 16925 Bearing 2RS-6204 20x47x14 for H35S C8024
16900 Sharpening Assembly for H35S A1026 36564
36536
16902 Ring EL.Benzing 8 for H35S A5406 36567 Bushing DU 12x14x25 for H35S B6222 16926 Bearing 2RS-6000 (10x26x8) for H35S C8067
17281 Ring EL.Seeger Ext.25 for H35S A5453 60449 Meat Tray Support Bushing for H35S B6230 60423 Touch Pad Gasket for H35S C8242
77585
19484 Ring 52 for H35S A5485 17313 Bushing DU 14x15x16 for H35S B6244 19637 Nut M3 for H35S D0101
19612 Ring 33 for H35S A5495 23646 Sharpener Pivot Ferrule for H35S B6256 77504 Stainless Steel Nut U5587 M4 for H35S D0102X
17283 Oil Seal 25x52x10 for H35S A5809 77552 Bushing for Plate for H35S B6332 77612 Self-Locking Nut M3 UNI7473 for H35S D0110
77601 Oil Seal for H35S A5848 77503 Bushing DU 12x14x30 INOX for H35S B6336 77535 Special Nut M10 for H35S D0116
17287 O-Ring 123 17.86x2.62 for H35S A5852 60443 Pusher Arm for H35S B7824 16928 Nut U5589 M6 for H35S D0133
77602 O-Ring 4500 for H35S A5857 77518 Sharpener Cover for H35S C1616 19639 Nut M8 for H35S D0135
77603 O-Ring 2037 9,25x1,78 for H35S A5861 60444 Meat Tray Handle Sliding Shaft for H35S
77604 O-Ring 2056 14x1,78 for H35S A5862 77605
77547 Pin Stop Ring for H35S A5921 78287 Power Cord 230/50 for H35S C3290 36643 Nut U5588 M5 for H35S D0160
77502 Shaft Sealing Ring Ø98x42 for H35S A5946 79105
36544 Carriage Rod for H35S B1010A 79263 Contact Pin for H35S C3352 36646 Nut U5588 M6 Stainless Steel for H35S D0163X
77548 Tray Rod for H35S B1038 36601 Rivet 1.9x5 for H35S C4640 36647 Nut U5588 M8 for H35S D0165
60431
36548 Shock Absorber Bar 12x170 for H35S B1251 36608 Capacitor 8 MF 400V for H35S C5806A 36651 Sharpener Support Nut for H35S D0183
79618 Sliding Bar for Carriage for H35S B1256 16913 Capacitor 14 MF 400V for H35S C5812 79264 Blade Support Screw for H35S D5454
60430 Carriage Shaft for H35S B1705 36609 Capacitor 20 µF 250V for H35S C5814 60435
60432 Body Casing for H35S B1903 77607 Connector BM00219 for H35S C6023 19648 Knife Spacer for H35S D5602
16904 Bushing Sharpener for H35S B6048 77608 Three-Phase Connector 3x16A for H35S C6080 77556 Right Spacer INT90 for H35S D5624
16905 Bushing DU 16x18x15 for H35S B6053 77609
17304 Bushing for H35S B6056 77610 Box Cover for P.C. Board for H35S C6446 36661
17305 Bushing DU 18x20x15 for H35S B6057 60461 Motor Frontplate for H35S C6461
19514 Bushing Guard A310 for H35S B6061 60455 Motor Backplate for H35S C6462 60438
16906 Bush Sharpening for H35S B6075 36614 Cover Anter.Motor H (Diam.135) for H35S C6464 77555
16907 Bush Sharpening for H35S B6076 36615 Back Motor Cover for H35S C6466 36665 Locknut Spacer for H35S D577018
17307 Bushing Sharpener for H35S B6083 60453 Motor Fan Cover Diam.110 for H35S C6572 77519 Spacer Eccentrico for H35S D577141
19630 Bushing Fastener HBC for H35S B6104B 36617 Motor Fan Cover for H35S C6573 77590 Cam for Sharpener for H35S E1461
78265 Bushing Funnel for H35S B6110 19534 Housing Sharpener H for H35S C6807 17345 Cam Bearing for H35S E1458
77550 Bushing DU 10x12x10 for H35S B6 111 19537 Rack for H35S C7245 36677 Cam Pin for H35S E1460
77588
Ring EL.Benzing 6 Stainless Steel for
H35S
Ring EL.Seeger EST.25 SER.Heavy
for H35S
Complete Carriage Rail Assembly for
H35S
Bushing Fastener Guard Knife A310 A
for H35S
A5404X 36566 Bushing for Carriage Springs for H35S B6221 36631 Bearing 2RS-6205 25x52x15 for H35S C8056
A5454 36569 Fixing Lever Bushing for H35S B6239 36591 Carriage Support for H35S C185404
B1080 36607
B6140 17334 Bearing 2Z-6205 25x52x15 for H35S C8011 60450 Cam for Sharpener for H35S E1462
Bushing for Carriage Support 23mm
for H35S
Assembly Wiring 6 Poles LG.400 for
H35S
CAVO (ROTOLI) FROR 450/750V 4X1
for H35S
Blade Cover Bolt Keeper 14x14 M for
H35S
Connettore Spina Monofase 2x16A for
H35S
B6214 36630 Bearing 5x16x6.5 for H35S C8035
C1884 36638 Nut U5589 M10 Stainless Steel for H35S D0137X
C3236 19642 Nut M8 for H35S D0155X
C3293 36645 Normal Nut U5588 M4 for H35S D0161
C5007 36648 Nut U5588 M8 for H35S D0165X
Meat Carriage Guard Holder Spacer
for H35S
C6081 17341 Spacer D.10.5x14 H.9 for H35S D5643
Carriage Shock Absorber Spacer for
H35S
77505 Stainless Steel Nut U5588 M12 for H35S D014215
Meat Carriage Guard Holder Screw
for H35S
Domed Nut Din 917 M8 Stainless Steel
for H35S
D5455
D5762
D014315
D014515
22
Page 23
Parts Breakdown
Model MS-IT-0350-H 39631
Item No. Description Position Item No. Description Position Item No. Description Position
77558 Eccentric for H35S E1471 19250 Spring 24.8x1.8x15 for H35S M7071 77511 Pin Deector for H35S P3653
19564 Cam 25mm for H35S E1474 36746 Spring 7x0.8x23 Cam for H35S M7076 77565 Pivot Pusher for H35S P3654
79267 Cam Eccentric Stroke mm.16 for H35S E1489 19248 Spring 15.6x20x2.2 for H35S M7120 77523 Knife Cover Support Pin for H35S P3655
36680 Carriage Felt for H35S F1606 36749 Carriage Bar Spring 25-28-1.5 for H35S M7121 77524 Pin for Protec.Support for H35S P3656
77614 Nylon Cable Tie (Diam.45x200) for H35S F2815 78283 Screw for H35S M7132 77566 Pivot Pusher for H35S P3663
36682 Unhook Friction Clasp 12x22x8 for H35S F3015 60462 Motor 230-50 H for H35S M8240 77594 Assembly Driving Pivot for H35S P3697
77591 Suppor Blade Flange for H35S F6039 60459 Motor EL.400-50 H for H35S M8241 19832 Flat Bar for H35S P4651
36686 Handling Flange for H35S F609076 60470 Motor 240/50/1 for H35S M8242 60469 Motor Straight Bracket for H35S P4869
17351 Locknut for H35S G5018 17382 Motor for H35S M8244 60458 Motor L-Bracket for H35S P4956
36689 Stainless Steel Locknut for H35S G5027 17383 Motor for H35S M8256 16961 Foot for H35S P5008
36691 Ring for Bushing for H35S G5053 60463 Motor 220/60 for H35S M8259 79617 Sliding Flat Bar for H35S P5102
36692 Ring for Cam for H35S G5054 19791 Oiler for H35S O4040 60446 Meat Tray Slider Bottom Plate for H35S P5348
36695 Ring Support Cap for H35S G5055 36759
77559 Plate Bar Supp. Ring 250/273 for H35S G5056 36760 Pin Ttray Shock-Absorber for H35S P1025 60439
60457 Index Locknut M4 2 P1 for H35S G5063 19796 Plastic Shock for H35S P1031 19655 Meat Grip Stud H for H35S P7420
36697 Logging Lock Nut GL25 for H35S G5064 17392 PL.Shock Absorb 8.5x20 for H35S P1034 60424 Touch Pad Screw for H35S P7447
60436 Meat Carriage Guard Holder Bushing G5103 19797 Nylon Shock 8.5x8 for H35S P1042 77539 Stud Plate M8x25x35 for H35S P7474
77615 Assembly P.C.B. C-H-M for H35S I1675 19798 Plastic Shock for H35S P1045 19850 Protection for H35S P7856
17352
19580 Handle TS8 for H35S I1907 77562 Shock Absorber for H35S P1054 78282 Lock Washer for H35S P8620
17356 Fastener Handle for H35S I1926 16955 Shock Absorber for H35S P1059 36865 Sharpener Operating Handle for H35S P8625
19587 Sharpener Knob for H35S I1957A 77563 Shock Absorber for H35S P1065 78284 Bracket for H35S P8626
36705 Adjustment Knob for H35S I1970A 17395 Shock Absorber for H35S P1081 36761 Shock Absorber for H35S P103401
36708 Assembly Index Knob for H35S I1990A 60434 Meat Carriage Guard Holder for H35S P1369 60451 Pivot Sharpener H-L-M25R for H35S P320561
17363 End Grip Handle for H35S I2040 60427 Blade Guard for H35S P1676 17419 Pin Truing for H35S P322601
36714 Blade Cover Handling for H35S I2058 60425 Blade Cover for H35S P1678 79270 Lock Plate Pivot H for H35S P344016
36717 Knob Assembly for H35S I2098 77616 Strain Relief for H35S P2004 77537 Ecc. Locking Plate for H35S P486081
17364 Nylon Gear DP 56, 80, Z29 for H35S I2404 36776 Strain Relief for H35S P2009 19657 Washer 4 for H35S R6003
18220 Knob Handling for H35S I203576 60421 Eelectrical Conduit for H35S
36728 Knife for H35S L0623 36778 Wire-Press for H35S P2014 19661 Washer 8 for H35S R6030
79268 Nut for H35S M0816 36779 Core-Hitch+Nut for H35S P2015 78258 Washer 30.5x46.5x0.6 for H35S R6251
77520 Magnet Ø8 x 25 for H35S M0819 36780 Wire Pusher for H35S P2017 19665 Washer for H35S R6260
36737 Grinding Stone C for H35S M6602 19811 Pin Sharpener for H35S P3205 19666 Washer for H35S R6280
36739 Honing-Finishing Stone for H35S M6621 17416 Pin Sharpener for H35S P3207 19667 Washer 12x17x2 for H35S R6281
36741 Spring 2.9x4x12 Stainless Steel for H35S M7001 36782 Pin.Grinding for H35S P3225 36880 Washer U6592 3 for H35S R6504
17377 Spring 8.5x1.0x25 for SS H35S M7013 17427 Assembly Grinding Stone Pin for H35S P3381 17455 Washer U6592 4 for H35S R6505
17379 Spring 11.9x0.7x27 SS for H35S M7029 36793 Pin Handle for H35S P3430 36881 Washer U6593 5 (5.5x15x1.2) for H35S R6507
17380 Spring 13.4x1.3x30 SS for H35S M7030 17426 Assembly Honing Stone Pivot for H35S P3458 36883
19776 Spring 14x1.5x60 for H35S M7032 23645 Sharpener Pivot for H35S P3528 36884
19782 Spring 19.5x1.5x16.7 for H35S M7050 77564 Pin Support Meat Grip Arm H for H35S P3636 19668 Washer 10 for H35S R6530
17381 Spring 22 5x1 8x18 for H35S M7052 79272 Knife Shaft for H35S P3648 17458 Contact Washer for H35S R6806
Touch Pad Start/Stop Push Button for
H35S
I1680 36762 Rubber Plug for H35S P1053 77525 Mobile Protection for H35S P7919
Rubber Shock Absorber 12x19x2 for
H35S
P1012 60445 Meat Tray Slider Top Plate for H35S P5349
Meat Tray Pusher Plate for H35S P6760
P2011 19659 Washer 8 for H35S R6006
Washer U6592 6 Stainless Steel for
H35S
Washer U6592 8 Stainless Steel for
H35S
R6512X
R6520X
23
Page 24
Parts Breakdown
Model MS-IT-0350-H 39631
Item No. Description Position Item No. Description Position Item No. Description Position
36889 Washer 10.5x16x1 for H35S R6816 77571 Lock Pin Pusher Arm for H35S S7623 37018 Screw STTC U6113 M6x6 for H35S V6010
16969 Washer 18.2x25x0.5 for H35S R6840 60465 Stator 230-50 H (Tubo Alettato) for H35S S8527 37021 Screw for H35S V6030
17460 Washer 34.2x46x0.5 for H35S R6846 60467
19674 Washer for H35S R6848 78259 Stator 230/50-60 for H35S S8529 37023 Screw STEI U5929 M5x5 for H35S V6065
77540 Washer 6,2x14x0,6 for H35S R6854 60468
77596 Switch Washer A310 for H35S R6864 19870 Stator 120/60 for H35S S8562 37024 Screw STEI U5929 M6x6 for H35S V6066X
36892 Washer 17x30x4 for H35S R6874 60466 Stator 220-60 for H35S S8568 19692 Screw M6x8 for H35S V6067
16972 Washer 5.5x19x2.5 for H35S R6884 77597 Washer Bracket A310 for H35S S9009 37025 Screw Stei U5929 M6x8 for H35S V6067X
36893
36897 Special Washer 5.5x22x1.5 for H35S R6932 77572 Bracket for Plate Rod for H35S S9188 37029 Screw STEI U5929 M8x20 for H35S V6079
60437
60460
78261 Rotor (A3109 P2521) Stator for H35S R8021 77573 Hand Grip Arm Support for H35S S9425 19700 Screw M6x16 for H35S V6240
16973 Plate Wheel D.25x9.5 for H35S
77618
77512 Washer 8,5x18x2 for H35S R652215 77528 Ext.Knife Protect.Support for H35S S9489 19704 Screw M10x16 for H35S V6262
77513
19680 Ball 3 17 for H35S S3005 77621 Electr. Equipment Box for H35S S100484 19706 Screw for H35S V6278
17465 Ball 4.76 for H35S S3015 60448 Support Plate for H35S S880821 37050 Screw TC AUT.D7971 4.2x9 for H35S V6285
77622 P.C.B. 230-50 C-H for H35S S3221 19877 Rubber Cap for H35S T1001 77599
77623 Scheda Elettrica 400-50 for H35S S3223 36981 Rubber Cap for H35S T1004 77629
77624 P.C. Board 230-50 H for H35S S3227 19879 Label for H35S T1603 77600
77625 P.C.B. 230-24V/50 GL for H35S S3228 36985 Label Plate for H35S T1617A 37058 Stainless Steel Screw M4x8 for H35S V6370
77626 P.C.B. 230V/50HZ for H35S S3269 19883 Label Oil for H35S T1690 37059 Stainless Steel Screw M4x14 for H35S V6371
77627 P.C.B. 24V C.C.GL for H35S S3291 77628 Switch Overlay for H35S T1760 77546
36907 Index Arm for H35S S3802 79279 Blade Cover Fastener for H35S T5071 37067 Screw TE U5739 M5x20 for H35S V6423
77542
36920
36924 Pin M.E.U6875 6x30 for H35S S7546 79280 Knife Shaft Assembly for H35S T8093 19713 Screw Sharpener for H35S V7710
36926 Pin U7586 3x18 for H35S S7557 60429 Meat Tray Support for H35S T8544 37091 Screw H for H35S V7730
77569 Pin U7586 6x30 for H35S S7570 79282 Blade Support Shaft for H35S T9699 17503 Screw M5x13 for H35S V7908
17476 Foot Support Pin D.10 M8 L.37 for H35S S7595 79283 Shaft Pin for H35S T9742 19715 Screw Sharpener for H35S V7910
77526 Pin Ø8x23 for H35S S7608 60454 Fan INT90 for H35S V4005 19717 Screw M6x50 for H35S V7917
77570
Stainless Steel Special Washer 8.5x24x2
for H35S
Meat Carriage Guard Holder Washer
for H35S
Rotor (A3105 P2520) KG.1,80 Each
for H35S
Washer U6592 4 Stainless Steel for
H35S
Stainless Steel Washer U6592 12 for
H35S
Cylindrical Pin U1707 8x35 Stainless
Steel for H35S
Pin 4x25 for H35S S7526 42974 Tie Rod for H35S T5191 17498 Screw TSPEI U5933 M4x10 for H35S V7043
Lock Pin for Carr. Plate Rotation for
H35S
R6897X 77527 Protec. Support for H35S S9185 19694 Screw M8x10 for H35S V6075
R6956 19181 Bracket Support for H35S S9192 19697 Screw M5x16 for H35S V6211
R8019 60422 Touch Pad Back Casing for H35S S9236 19699 Screw M4x25 for H35S V6231
R8520 77574 Hand Grip Support for H35S S9434 77598
R650515 79619 Sharpener Holder for H35S S9449 37042 Screw TCEI U5931 M8x25 for H35S V6254
R654015 77620 Control Box for H35S S100481 77530 Screw TCEI U5931 M10x30 for H35S V6264
S7432 60456 H Motor Fastener for H35S T5157 17497
S7618 37013 Motor Fan MEC80 148x16 for H35S V4014 19917 Screw BS for H35S V7960
Statore 400-50 H (Tubo Alettato) for
H35S
Statore 120-60 H (Tubo Alettato) for
H35S
S8528 60426
S8561 19691 Grub Screw M6x6 for H35S V6066
Stainless Steel Screw STEI U5923
M8x60 for H35S
Stainless Steel Screw TCEI U5931
M6x20 for H35S
Screw TC TC AUT.D7981 4,2x16 for
H35S
Screw TBTC AUT.U6954 4,2x13 for
H35S
Screw TBTC AUT.U6954 3,9x32 for
H35S
Screw TE U5737 M6x15 Stainless Steel
for H35S
Screw TSP U6109 M5x15 Stainless
Steel for H35S
V6041
V6245X
V6292
V6296
V6297
V6421X
V7014X
24
Page 25
Parts Breakdown
Model MS-IT-0350-H 39631
Item No. Description Position Item No. Description Position Item No. Description Position
37095 Screw for Rod 6x13 for H35S V7993A 77581 Special Screw M10x18 for H35S V8103 77545
19724 Screw H for H35S V8001 77582 Special Screw Ø8x15 for H35S V8104 77630
16987 Special Screw M6x15 for H35S V8020 77532 Special Screw M8x40 for H35S V8121 77578
37102 Screw M6x20 for H35S V8035 60447
19920 Screw M8x30 for H35S V8036 60433 Meat Carriage Guard for H35S V313006 37083
37104 Threaded Stud for H35S V8042 60428 Threaded Rod for H35S V605315 37085 Screw 8x25 for H35S V705616
77580 Stainless Steel Screw M8x16 for H35S V8051 77515 Screw TC U6107 M4x25 INOX for H35S V623115
37113 Screw for Carr. Index M8x25 for H35S V8099 77531
Meat Tray Slider Bottom Plate Screw
for H35S
Screw TCEI U5931 M6x14 INOX for
H35S
V8160 37077 Screw Tsp U6109 M4x6 INOX for H35S V700615
V628915
Stainless Steel Screw TCEI U5931
M8x45 for H35S
Stainless Steel Screw TCEI U5931 M
4x12 for H35S
Stainless Steel Screw TE U5739 M8x14
for H35S
Locking Screw-Support H-C (CE) for
H35S
V633115
V634415
V645715
V705016
25
Page 26
Electrical Schematics
Model MS-IT-0350-H 39631
Position Description Position Description Position Description
X1 Spina C1 Capacitor 220uF K1 Power Relay
T1 Transformer C2 Capacitor 100uF K2 Power Relay
F1 Fuse 500mA C3 Capacitor 20uF K3 Command Relay
D1 Straightener 1A R1 Resistance 1k K4 Command Relay
D2 Protective Diode R2 Resistance 1k S1 Stop Button
L1 LED Orange Line R3 Resistance 10k S2 Start Button
L2 LED Green March R4 Resistance 47 Hom S3 Blade Guard Disc Protection
26
Page 27
Warranty Registration
Thank you for purchasing an Omcan product. To register your warranty for this product, complete the information below, tear off the card at
the perforation and then send to the address specied below. You can also register online by visiting:
Merci d’avoir acheté un produit Omcan. Pour enregistrer votre garantie pour ce produit, complétez les informations ci-dessous, détachez la
carte au niveau de la perforation, puis l’envoyer à l’adresse spécié ci-dessous. Vous pouvez également vous inscrire en ligne en visitant:
Gracias por comprar un producto Omcan usted. Para registrar su garantía para este producto, complete la información a continuación,
cortar la tarjeta en la perforación y luego enviarlo a la dirección indicada a continuación. También puede registrarse en línea en:
www.omcan.com/warrantyregistration.html
For mailing in Canada
Pour postale au Canada
Por correo en Canadá
OMCAN
PRODUCT WARRANTY REGISTRATION
3115 Pepper Mill Court,
Mississauga, Ontario
Canada, L5L 4X5
PRODUCT WARRANTY REGISTRATION
4450 Witmer Industrial Estates, Unit 4,
For mailing in the US
Pour diffusion aux États-Unis
Por correo en los EE.UU.
OMCAN
Niagara Falls, New York
USA, 14305
or email to: service@omcan.com
Purchaser’s Information
Name: Company Name:
Address:
Telephone:
City: Province or State: Postal or Zip: Email Address:
Country: Type of Company:
Restaurant Bakery Deli
Dealer from which Purchased: Butcher Supermarket Caterer
Dealer City: Dealer Province or State: Institution (specify):
Invoice: Other (specify):
Model Name: Model Number: Serial Number:
Machine Description:
Date of Purchase (MM/DD/YYYY): Date of Installation (MM/DD/YYYY):
Would you like to extend the warranty? Yes No
Thank you for choosing Omcan | Merci d’avoir choisi Omcan | Gracias por elegir Omcan
27
Page 28
Since 1951 Omcan has grown to become a leading distributor of equipment and supplies to the North
American food service industry. Our success over these many years can be attributed to our commitment
to strengthen and develop new and existing relationships with our valued customers and manufacturers.
Today with partners in North America, Europe, Asia and South America, we continually work to improve
and grow the company. We strive to offer customers exceptional value through our qualied local sales
and service representatives who provide convenient access to over 3,500 globally sourced products.
Depuis 1951 Omcan a grandi pour devenir un des “leaders” de la distribution des équipements et
matériel pour l’industrie des services alimentaires en Amérique du Nord. Notre succès au cours de ces
nombreuses années peut être attribué à notre engagement à renforcer et à développer de nouvelles
et existantes relations avec nos clients et les fabricants de valeur. Aujourd’hui avec des partenaires en
Amérique du Nord, Europe, Asie et Amérique du Sud, nous travaillons continuellement à améliorer et
développer l’entreprise. Nous nous efforçons d’offrir à nos clients une valeur exceptionnelle grâce à
nos ventes locales qualiées et des représentants de service qui offrent un accès facile à plus de 3500
produits provenant du monde entier.
Desde 1951 Omcan ha crecido hasta convertirse en un líder en la distribución de equipos y suministros
de alimentos en América del Norte industria de servicios. Nuestro éxito en estos años se puede atribuir
a nuestro compromiso de fortalecer y desarrollar nuevas relaciones existentes con nuestros valiosos
clientes y fabricantes. Hoy con socios de América del Norte, Europa, Asia y América del Sur, que trabajan
continuamente para mejorar y crecer la empresa. Nos esforzamos por ofrecer a nuestros clientes valor
excepcional a través de nuestro local de ventas y representantes de los servicios que proporcionan un
fácil acceso a más de 3,500 productos con origen a nivel mundial.
Loading...