Page 1
Baking Mixers
Models MX-CN-0020-G, 0020-T, 0030-G, 0030-T, 0010-G
Items 20467, 20441, 17835, 20442, 17836
Instruction Manual
Revised - 06/15/2022
Toll Free: 1-800-465-0234
Fax: 905-607-0234
Email: [email protected]
www.omcan.com
Page 2
Table of Contents
Model MX-CN-0010-G / Model MX-CN-0020-G / Model MX-CN-0020-T
Model MX-CN-0030-G / Model MX-CN-0030-T
Section
General Information
Safety and Warranty
Technical Specications
Installation
Operation
Maintenance
-------------------------------------------------------------------------------------------- 7
--------------------------------------------------------------------------------------- 7 - 12
--------------------------------------------------------------------------------------- 12
--------------------------------------------------------------------------- 3 - 4
--------------------------------------------------------------------------- 4 - 5
Page
---------------------------------------------------------------------- 5 - 6
Troubleshooting
Mixer Capacity Chart
Parts Breakdown
Electrical Schematics
Warranty Registration
----------------------------------------------------------------------------- 12 - 13
---------------------------------------------------------------------------- 15 - 20
----------------------------------------------------------------------------- 14
---------------------------------------------------------------------- 21 - 26
---------------------------------------------------------------------------- 27
2
Page 3
General Information
Omcan Manufacturing and Distributing Company Inc., Food Machinery of America, Inc. dba Omcan
and Omcan Inc. are not responsible for any harm or injury caused due to any person’s improper or
negligent use of this equipment. The product shall only be operated by someone over the age of 18, of
sound mind, and not under the inuence of any drugs or alcohol, who has been trained in the correct
operation of this machine, and is wearing authorized, proper safety clothing. Any modication to the
machine voids any warranty, and may cause harm to individuals using the machine or in the vicinity of
the machine while in operation.
CHECK PACKAGE UPON ARRIVAL
Upon receipt of an Omcan shipment please inspect for external damage. If no damage is evident on the
external packaging, open carton to ensure all ordered items are within the box, and there is no concealed
damage to the machine. If the package has suffered rough handling, bumps or damage (visible or concealed),
please note it on the bill of lading before accepting the delivery and contact Omcan within 24 hours, so we may
initiate a claim with the carrier. A detailed report on the extent of the damage caused to the machine must be
lled out within three days, from the delivery date shown in the shipping documents. Omcan has no recourse
for damaged products that were shipped collect or third party.
Before operating any equipment, always read and familiarize yourself with all operation and safety
instructions.
Omcan would like to thank you for purchasing this machine. It’s of the utmost importance to save
these instructions for future reference. Also save the original box and packaging for shipping the
equipment if servicing or returning of the machine is required.
---------------------------------------------------------------------------------------------------------------------------------------------------
Omcan Fabrication et distribution Companie Limité et Food Machinery d’Amerique, dba Omcan et
Omcan Inc. ne sont pas responsables de tout dommage ou blessure causé du fait que toute personne
ait utilisé cet équipement de façon irrégulière. Le produit ne doit être exploité que par quelqu’un de
plus de 18 ans, saine d’esprit, et pas sous l’inuence d’une drogue ou d’acohol, qui a été formé pour
utiliser cette machine correctement, et est vêtu de vêtements de sécurité approprié. Toute modication
de la machine annule toute garantie, et peut causer un préjudice à des personnes utilisant la machine
ou des personnes à proximité de la machine pendant son fonctionnement.
VÉRIFIEZ LE COLIS DÈS RÉCEPTION
Dès réception d’une expédition d’Omcan veuillez inspecter pour dommages externes. Si aucun dommage
n’est visible sur l’emballage externe, ouvrez le carton an de s’assurer que tous les éléments commandés
sont dans la boîte, et il n’y a aucun dommage dissimulé à la machine. Si le colis n’a subi aucune mauvaises
manipulations, de bosses ou de dommages (visible ou cachée), notez-le sur le bond de livraison avant
d’accepter la livraison et contactez Omcan dans les 24 heures qui suivent, pour que nous puissions engager
une réclamation auprès du transporteur. Un rapport détaillé sur l’étendue des dommages causés à la machine
doit être rempli dans un délai de trois jours, à compter de la date de livraison indiquée dans les documents
d’expédition. Omcan n’a aucun droit de recours pour les produits endommagés qui ont été expédiées ou cueilli
par un tiers transporteur.
3
Page 4
General Information
Avant d’utiliser n’importe quel équipement, toujours lire et vous familiariser avec toutes les opérations
et les consignes de sécurité.
Omcan voudrais vous remercier d’avoir choisi cette machine. Il est primordial de conserver ces
instructions pour une référence ultérieure. Également conservez la boîte originale et l’emballage pour
l’expédition de l’équipement si l’entretien ou le retour de la machine est nécessaire.
---------------------------------------------------------------------------------------------------------------------------------------------------
Omcan Empresa De Fabricacion Y Distribucion Inc. Y Maquinaria De Alimentos De America, Inc. dba
Omcan y Omcan Inc. no son responsables de ningun daño o perjuicío causado por cualquier persona
inadecuada o el uso descuidado de este equipo. El producto solo podra ser operado por una persona
mayor de 18 años, en su sano juicio y no bajo alguna inuencia de droga o alcohol, y que este ha sido
entrenado en el correcto funcionamiento de esta máquina, y ésta usando ropa apropiada y autorizada.
Cualquier modicación a la máquina anúla la garantía y puede causar daños a las personas usando la
máquina mientras esta en el funcionamiento.
REVISE EL PAQUETE A SU LLEGADA
Tras la recepcion de un envio Omcan favor inspeccionar daños externos. Si no hay daños evidentes en el
empaque exterior, Habra el carton para asegurararse que todos los articulos solicitados ésten dentro de la
caja y no encuentre daños ocultos en la máquina. Si el paquete ha sufrido un manejo de poco cuidado, golpes
o daños (visible o oculto) por favor anote en la factura antes de aceptar la entrega y contacte Omcan dentro
de las 24 horas, de modo que podamos iniciar una reclamación con la compañia. Un informe detallado sobre
los daños causados a la máquina debe ser llenado en el plazo de tres días, desde la fecha de entrega que se
muestra en los documentos de envío. Omcan no tiene ningun recurso por productos dañados que se enviaron
a recoger por terceros.
Antes de utilizar cualquier equipo, siempre lea y familiarizarse con todas las instrucciones de
funcionamiento y seguridad.
Omcan le gustaría darle las gracias por la compra de esta máquina. Es de la mayor importancia para
salvar estas instrucciones para futuras consultas. Además, guarda la caja original y el embalaje para el
envío del equipo si servicio técnico o devolución de la máquina que se requiere.
Safety and Warranty
RESIDENTIAL USERS: Vendor assumes no liability for parts or labor coverage for component failure
or other damages resulting from installation in non-commercial or residential applications. The right
is reserved to deny shipment for residential usage; if this occurs, you will be notied as soon as
possible.
1 YEAR PARTS AND LABOUR WARRANTY
4
Page 5
Safety and Warranty
Within the warranty period, contact Omcan Inc. at 1-800-465-0234 to schedule an Omcan authorized
service technician to repair the equipment locally.
Unauthorized maintenance will void the warranty. Warranty covers electrical and part failures, not
improper use.
Please see https://omcan.com/disclaimer for complete info.
WARNING:
The packaging components are classied as normal solid urban waste and can therefore be disposed of
without difculty.
In any case, for suitable recycling, we suggest disposing of the products separately (differentiated
waste) according to the current norms.
DO NOT DISCARD ANY PACKAGING MATERIALS IN THE ENVIRONMENT!
Technical Specications
1. Gear change hand lever.
2. Planetary Shaft.
3. Mixer Attachment.
4. Stainless bowl.
5. Power switch.
6. Bowl lift handle.
7. Safety guard.
8. Support Frame.
9. #12 Hub
10. Internal Safety Switch
11. Safety Switch
12. Overload Reset Button
5
Page 6
Technical Specications
10 QT MIXERS
Model MX-CN-0010-G
Power 0.67 HP / 0.5 kW
Shaft RPM 108
1st
| 195
Capacity 9.5 L / 10 QT
Timer No
Guard Yes
Electrical 110V / 60Hz / 1
Packaging Weight 181 lbs. / 82.1 kgs.
Dimensions 20” x 15.5” x 24.5” / 508 x 394 x 622mm
Packaging Dimensions 22” x 18” x 29” / 559 x 457 x 737mm
Item Number 20467
20 QT MIXERS
Model MX-CN-0020-G MX-CN-0020-T
Power 1.5 HP / 1.12 kW
Shaft RPM 108
1st
| 195
Capacity 18.9 L / 20 QT
Timer No Yes
Guard Yes
Electrical 110V / 60Hz / 1
Packaging Weight 262 lbs. / 118.8 kgs.
Dimensions 21.5” x 16” x 30.5” / 546 x 406 x 775mm
Packaging Dimensions 25” x 22” x 35” / 635 x 559 x 889mm
Item Number 20441 17835
2nd
| 355
2nd
| 355
3rd
3rd
30 QT MIXERS
Model MX-CN-0030-G MX-CN-0030-T
Power 2 HP / 1.5 kW
Shaft RPM 91
1st
| 166
2nd
| 282
3rd
Capacity 29.4 L / 30 QT
Timer No Yes
Guard Yes
Electrical 110V / 60Hz / 1
Packaging Weight 433 lbs. / 196.8 kgs.
Dimensions 23.5” x 21” x 44.5” / 597 x 533 x 1130mm
Packaging Dimensions 29” x 26” x 50” / 737 x 660 x 1270mm
Item Number 20442 17836
6
Page 7
Installation
UNCRATING
Immediately after uncrating the mixer, check for possible shipping damage. If the machine is found to be
damaged after uncrating, save all packaging materials and contact the carrier within 3 days of delivery. Failure
to contact the carrier or supplier in a timely fashion may cause you a loss.
LOCATION
Prior to installation, test the electrical service to assure that it agrees with the specications on the machine’s
rating plate. Place the mixer on a sturdy and level surface. There should be adequate space around the mixer
for the user to operate the controls and to install and remove the bowls. Holes are located in the base to
permanently secure the mixer, although this is not necessary in normal installations.
ELECTRICAL CONNECTIONS
The electrical cords on these machines are equipped with a three-pronged grounding plug, which must be
connected to a properly grounded receptacle. If the receptacle is not properly grounded, contact an electrician.
DO NOT remove the grounding prong from the plug. Electrical and grounding connections must comply with
the applicable regulations and local electrical codes.
Check Initial Operation
1. Install the bowl and raise into the mix position, with the bowl support up and bowl safety guard closed.
2. Apply power to the mixer by inserting the cord plug into a properly grounded outlet.
3. Turn the Speed Lever to position 1.
4. Run the machine by pushing the START and then the STOP buttons.
Operation
WARNING
Moving agitator in bowl. Keep hands, clothing and utensils out of bowl while in operation. Do not use
without interlocked safety guard.
WARNING: DO NOT SWITCH GEARS DURING USAGE.
The Omcan mixers are equipped with Standard Safety features. Refer to the diagram on page 3 for an
explanation of their functions. The bowl safety guard must be in the closed position or the mixer will not
operate. The bowl must be raised and remain in mixing position on bowl support or the mixer will not operate.
1. Standard power supply 110V / 60Hz AC. (Please use a plug with 3 wide contacts and good grounding.)
2. Speed transformation: if you want to change the speed, please turn off the power switch (5) rst, and then
7
Page 8
Operation
pull the gear change hand lever (1) to the position required.
3. Shutting down: when the operation is completed, turn off the power switch (5) rst, then pull the gear
change hand lever (1) to position 1, and lower bowl to load position (6), and nally disconnect the power
supply.
NOTES
• The power socket must be provided with a good ground wire to guarantee the mixer is grounded properly.
There will be an electric shock if there is no ground wire or if it is improperly mounted. Never connect the
ground wire to gas pipes, water pipes, lightning rods or telephone lines. Electric leakage should be checked
after installation. If the power line is damaged, it must be replaced by the a Service Company.
• Do not put your hand into the stirring barrel during operation. Disconnect the power supply before the
installation of the mixer.
• Do not operate the mixer beyond the time limit to prevent reduction of its service life.
• The mixer should be mounted on a stable and clean place, keep it away from heat sources and wet places,
and away from equipment with strong electromagnetic properties.
• Keep the machine clean constantly. Disconnect power supply before maintenance. Clean machine with a
soft damp cloth. Do not clean it with water spray or use harsh detergents.
On/Off Switch - MX-CN-0010-G
Features:
1. Standard Controls
On/Off Switch - MX-CN-0020-T
Features:
1. On Button
2. Off Button
3. Countdown Timer Knob
1
3
1
2
8
Page 9
On/Off Switch - MX-CN-0020-G
Operation
Features:
1. On Button
2. Off Button
On/Off Switch - MX-CN-0030-T
Features:
1. Separate On and Off Switches
2. Countdown Timer Knob
3. Speed Adjusting Lever with Handle
1
2
1
23
On/Off Switch - MX-CN-0030-G
Features:
• On Button
• Off Button
• Speed Adjusting Lever with Handle
1
3
2
9
Page 10
Operation
Installing Mixer Bowls - All Models
1. Place the bowl on the two arms to keep it in place. Insert the bowl pin into pin support located on frame.
Carefully align holes on the bowl with the studs on the bowl arms. (Fig.1)
2. Once the bowl is seated properly, swing the locking levers into position. (Fig.2)
3. To remove the bowl, follow the instructions above in reverse order.
Fig.1
MX-CN-0010-G / 0020-T / 0020-G
MX-CN-0030-T / 0030-G
Fig.2
10
Page 11
Operation
Installing Mixer Attachments - MX-CN-0010-G
Ensure machine is off, lower bowl to loading position. Keep note of the notch on the shaft (Fig.3) and raise the
attachment over the shaft. (Fig.4) Turn the attachment to the left until you can turn no more (Fig.5) and release,
the attachment should now dip down a bit and lock in place. To Remove the attachment, follow the instructions
above in reverse order.
Fig.3
Fig.4 Fig.5
Installing Mixer Attachments - MX-CN-0020-T / MX-CN-0020-G
Ensure machine is off, lower bowl to loading position. Open the Guard by pulling the handle away from
the magnetic latch. (Fig.6) Raise the attachment over the shaft, keeping note of where the notch is. (Fig.7)
Guide the notch through the path until it reaches the end and locks. (Fig.8) To remove attachment, follow the
instructions above in reverse order.
Fig.6 Fig.7 Fig.8
Installing Mixer Attachments - MX-CN-0030-T / MX-CN-0030-G
Ensure machine is off, lower bowl to loading position. Open the Guard by lifting it up towards the top of the
machine until it stops. (Fig.9) Raise the attachment through the shaft, keeping note of where the notch is.
(Fig.7) Guide the notch through the path until it reaches the end and locks. (Fig.8) To remove attachment,
follow the instructions above in reverse order.
11
Page 12
Operation
Fig.9
Maintenance
Clean the bowl and attachments daily or after use to maintain hygiene standards. Clean the mixer with a soft
wet cloth. The transmission gear box is greased in factory. Check the greasing each 6 months. To add or rell
grease, open the top cover, then ll grease from aperture or replace the grease directly. Ensure guide rails are
kept clean and lubricated.
Troubleshooting
Problems Causes Solutions
Planetary does not rotate after
starting the machine
Oil leakage The seal rings are worn out Replace seal rings
Loose electric wiring Check electric wiring tighten any
loose connections. Press reset
button.
12
Page 13
Troubleshooting
Motor temperature raises while
reduced output speed
The mixing knocks with the bowl The attachment or bowl is
Abnormal noise and high
temperature from gearbox
Bowl lift is difcult to pull up Guide rails are not lubricated. Lubricate guide rails.
Too low voltage Check the power supply
Over-loaded Reduce load
The speed of mixing is too high, or
wrong attachment is being used, or
mixing too long.
deformed
Insufcient lubrication Add or replace the grease
Select a suitable speed and
attachment. Reduce load.
Repair of replace the attachment
or bowl
WARNING!
If the equipment is out of function, please make sure it is serviced by a professional person. Please turn to a
special service centre!
For parts or service call 1-800-465-0234.
13
Page 14
Mixer Capacity Chart
AGITATORS
SUITABLE
FOR
OPERATION
PRODUCT
CAPACITY OF BOWL (QTS. LIQUID) 10 20 30
Egg Whites Whip 1, 2, 3 1 1/2 pts 1 qt 1.5 qt
Mashed Potatoes Beater 1,2 8 lbs 12 lbs 20 lbs
Mayonnaise (Qts of Oil) Whip 1, 2 4 1/2 qts 10 qts 12 qts
Meringue (Qty. of Water) Whip 1, 2, 3 1/2 pts 3/4 pts 1 qt
Wafe or Hot Cake Batter Whip 1,2 5 qts 8 qts 12 qts
Whipped Cream Whip 1, 2, 3 2 1/2 qts 4 qts 6 qts
Cake, Box or Slab Beater 1,2 8 lbs 16 lbs 22 lbs
Cake, Cup Beater 1,2 8 lbs 16 lbs 22 lbs
Cake, Layer Beater 1,2 8 lbs 16 lbs 22 lbs
Cake, Pound Beater 1,2 8 lbs 16 lbs 22 lbs
Cake, Short (Sponge) Beater 1,2 6 lbs 12 lbs 16 lbs
Cookies, Sugar Beater 1,2 8 lbs 12 lbs 16 lbs
Dough, Bread or Roll (Lt.-Med.) 60% AR Hook 1 8 lbs 16 lbs 20 lbs
Dough, Heavy Bread 55% AR ** Hook 1 6 lbs 12 lbs 16 lbs
Dough, Pie Hook 1 8 lbs 14 lbs 20 lbs
Dough, Thin Pizza 40%(max mix time is 5 min.)*** Hook 1 N/R N/R 10 lbs
Dough, Med. Pizza 50% AR Hook 1 N/R N/R 12 lbs
Dough, Thick Pizza 60% AR Hook 1 N/R 10 lbs 14 lbs
Dough Raised Donut 65% AR Hook 1 N/R 6 lbs 10 lbs
Dough, Whole Wheat 70% AR Hook 1 6 lbs 10 lbs 16 lbs
Icing, Fondant Beater 1 5 lbs 9 lbs 14 lbs
Shortening & Sugar, Creamed Beater 1 7 lbs 12 lbs 18 lbs
Pasta, Basic Egg Noodle Hook 1 1 lbs 3 lbs 6 lbs
ALLOWABLE
AGITATOR
SPEEDS
0010-G
0020-G 0030-G
0020-T 0030-T
pts - Pints (US Liquid) ● qts - Quarts (US Liquid) ● lbs - Pounds (US Weight) ● N/R - Not Recommended
The following maximum capacities are intended as a guideline only, varying factors such as the type of our
used, temperature of water used, and other conditions may require the batch to be reduced. (1 gallon of water
weighs 8.33 lbs.)
NOTE: AR% = (Absorption Ratio % - water weight divided by our weight) The mixer capacity depends on the
moisture content of the dough. The capacities mentioned above are based on our at room temperature and
70°F water temperature. If high gluten our is used, reduce above dough batch size to 10% If using chilled
our, water below 70°F, or ice, reduce batch size by 10% 2nd speed should never be used on 50% AR
14
Page 15
Model MX-CN-0010-G 20467
Parts Breakdown
15
Page 16
Parts Breakdown
Model MX-CN-0010-G 20467
Item No. Description Position Item No. Description Position Item No. Description Position
25061 Wire Whip for 20467 1 25714 Nut 14x1.5 for 20467 33 25124 Ring for 20467 61
25062 Hook for 20467 2 25095 Declutch Shift Shaft for 20467 35 25125 Bearing for 20467 62
25065 Shifting Yoke for 20467 3-5, 34 25096 Spring Washer for 20467 36 25126 Shaft Worm Gear for 20467 63
25066 Flat Beater for 20467 6 25097 Gear for 20467 37 24915 Circlips for Shaft for 20467 64
25067 Gear (Comes with Elastic Ring) for 20467 7 24893 Spring Washers for 20467 38 25128 Worm Gear for 20467 65
25068 Nut for 20467 8 25099 Support for 20467 39 25125 Bearing for 20467 66
25069 Lining Ring for 20467 9 25100 Bearing for 20467 40 25131 Back Guard for 20467 68
25070 Bearing for 20467 10 25101 Spindle Boring Cover for 20467 41 25132 Worm Pole for 20467 69
24867 Speed Handle for 20467 11 25102 Big Gear for 20467 42-1 25133 Back Cover for 20467 70
25072 Handle Shaft for 20467 12 25103 Gear for 20467 42-2 25134 Motor Box for 20467 71
25073 Bushing for 20467 13 25104 Roller for 20467 42-3 25135 Crank Lever for 20467 72
25074 Oil Seal for 20467 14 24880 Spring for 20467 42-4 25136 Handle for 20467 73
24870 Tighten Handle for 20467 15 25106 Taper Gear Wheel 1 for 20467 43 25137 Connecting Rod for 20467 74
25076 Block Handle for 20467 16 25107 Motor for 20467 44 25138 Stand Column for 20467 75
24865 Handle Shifter Cover for 20467 17 25108 Combination of Gear for 20467 45 25139 Spring for 20467 76
24967 Plug for 20467 18 25109 Bushing for 20467 46 24939 Spacer for 20467 77
25079 Cam-Gear Shifter for 20467 19 25110 Claw Type Clutch for 20467 47 24883 Nut for 20467 78
25080 Attachment Hub for 20467 20 2 5111 Inner Gear for 20467 48 24908 Press Board for 20467 79
25081 Taper Gear Wheel 1 for 20467 21 25112 Gear Box for 20467 49 25143 Brand for 20467 80
25082 Circlips for Shaft for 20467 22 25113 Support for 20467 50 24922 Green Button Round for 20467 81
25083 Planetary Gear for 20467 23 25114 Base for 20467 51 24924
25084 Bearing for 20467 24 25115 Retainer-Spring for 20467 52 25146 Run Capacitor 20 UF for 20467
25085 Operating Shelf for 20467 25 24911 Nut for 20467 53 25147 Start Capacitor 100 UF for 20467
25086 Safety Guard for 20467 26 24882 Ring for 20467 54 24944 Contactor-Relay for 20467
25087 Working Shaft for 20467 27 25118 Gear Shaft for 20467 55 25149 Power Cord for 20467
25006 Bearing for 20467 28 25119 Key for 20467 56 25150 Reset-Overload Switch for 20467
25089 Oil Seal for 20467 29 24898 Circlips for Shaft for 20467 57 25151
25090 Bowl for 20467 30 25121 Gear for 20467 58 25152 Timer Knob for 20467
25091 Cover for 20467 31 25122 Bushing for 20467 59
24985 Plug Cover (Steel) for 20467 32 25123 Gear for 20467 60
Red Button Round without Timer for
20467
Safety Guard-Bowl Micro Switch for
20467
82
16
Page 17
Model MX-CN-0020-G 20441
Model MX-CN-0020-T 17835
Parts Breakdown
17
Page 18
Parts Breakdown
Model MX-CN-0020-G 20441
Model MX-CN-0020-T 17835
Item No. Description Position Item No. Description Position Item No. Description Position
25153 Wire Whip for 20441, 17835 1 24891 Working Shaft for 20441, 17835 35 24925 Red Button with Timer for 20441, 17835 67
25154 Dough Hook for 20441, 17835 2 24892 Retainer-Pin for 20441, 17835 36 24926 Brand for 20441, 17835 68
25155 Flat Beater for 20441, 17835 3 24893 Spring Washers for 20441, 17835 37 24927 Motor Box for 20441, 17835 69
25156 Safety Guard for 20441, 17835 4 24894 Pressing Plate for 20441, 17835 38 24928 Key for 20441, 17835 70
25157 Bowl for 20441, 17835 5 24895
24862 Shifting Yoke for 20441, 17835 6-9 25006 Bearing for 20441, 17835 40 24930 Gear for 20441, 17835 72
24863 Cam-Gear Shifter for 20441, 17835 10 24897 Spacer-Lower for 20441, 17835 41 24931 Motor for 20441, 17835 73
24864 Plate-Shifter Index for 20441, 17835 11 24898 Circlips for Shaft for 20441, 17835 42 24932 Back Housing for 20441, 17835 74
24865 Handle-Shifter Cover for 20441, 17835 12 25814 Taper Gear Wheel for 20441, 17835 43 24933 Back Cover for 20441, 17835 75
24866 Handle-Shifter for 20441, 17835 13 24900 Gear for 20441, 17835 44 24934 Handle-Shifter for 20441, 17835 76
24867 Speed Handle for 20441, 17835 14 24901 Bushing for 20441, 17835 45 24935 Crank Lever Q for 20441, 17835 77
24967 Plug for 20441, 17835 15 24902 Sleeve for 20441, 17835 46 24936 Connecting Rod for 20441, 17835 78
24869 Attachment Hub for 20441, 17835 16 24903 Claw Type Gear Wheel for 20441, 17835 47 24937 Stand Column for 20441, 17835 79
24870 Tighten Handle for 20441, 17835 17 24904 Gasket for 20441, 17835 48 24938 Spacer for 20441, 17835 80
24871 Ring for 20441, 17835 18 24905 Bearing 6205 for 20441, 17835 49 24939 Spacer for 20441, 17835 81
24872 Tapered Gear Wheel for 20441, 17835 19 24906 Bushing for 20441, 17835 50 24940 Spring for 20441, 17835 82
24873 Top Cover for 20441, 17835 20 24907 Oil Seal for 20441, 17835 51 24941 Hood Ring for 20441, 17835 83
25714 Nut 14x1.5 for 20441, 17835 21 24908 Press Board for 20441, 17835 52 16323 Run Capacitor - 40 UF for 20441, 17835
24875 Pressing Plate for 20441, 17835 22 24909 Support for 20441, 17835 53 24943
24985 Plug Cover (Steel) for 20441, 17835 23 24910 Base for 20441, 17835 54 24944 Contactor-Relay for 20441, 17835
24877 Big Gear for 20441, 17835 24-1 24911 Nut for 20441, 17835 55 24945 Power Cord for 20441, 17835
24878 Gear for 20441, 17835 24-2 24912 Bearing 6201 for 20441, 17835 56 25204
24879 Roller 8x15 for 20441, 17835 24-3 24913 Mid-Gear Wheel for 20441, 17835 57 24946 Reset-Overload Switch for 20441, 17835
24880 Spring for 20441, 17835 24-4 24914 Key for 20441, 17835 58 25202
24881 Declutch Shift Shaft for 20441, 17835 25 24915 Circlips for Shaft for 20441, 17835 59 25203 Knob for 20441, 17835
24882 Ring for 20441, 17835 26 24916 Gear for 20441, 17835 60 24947
24883 Nut for 20441, 17835 27 24917 Bushing for 20441, 17835 61 25205 Screw for 20441, 17835
24884 Main Shaft for 20441, 17835 28 24918 Gear for 20441, 17835 62 25152 Timer Knob for 20441, 17835
24885 Gear Box for 20441, 17835 29 24919 Plug Cover for 20441, 17835 63 64156
24886 Internal Gear for 20441, 17835 30 25013 Worm Wheel for 20441, 17835 64 AC907 Bowl Locating Pin for 20441, 17835
24887 Gear for 20441, 17835 31 24921 Oil Seal for 20441, 17835 65 69760
24888 Operating Shelf for 20441, 17835 32 24922 Green Button Round for 20441, 17835 66 69761
25070 Bearing 6204 for 20441, 17835 33 24923
24890 Oil Seal for 20441, 17835 34 24924
Transmission Shaft Support for 20441,
17835
Green Button with Timer for 20441,
17835
Red Button Round without Timer for
20441, 17835
39 24929 Shaft Worm Gear for 20441, 17835 71
Start Capacitor - 300 UF for 20441,
17835
Magnet for Safety Guard for 20441,
17835
Bowl Guard Clip Plastic for 20441,
17835
Safety Guard - Bowl Switch for 20441,
17835
Locking Screws of Press Board for
20441, 17835
Top Cover Screw M6x30 for 20441,
17835
Top Cover Screw M6x40 for 20441,
17835
66
67
18
Page 19
Model MX-CN-0030-G 20442
Model MX-CN-0030-T 17836
Parts Breakdown
19
Page 20
Parts Breakdown
Model MX-CN-0030-G 20442
Model MX-CN-0030-T 17836
Item No. Description Position Item No. Description Position Item No. Description Position
24951 Dough Hook for 20442, 17836 1 24989 Gear for 20442, 17836 38-2 25026 Gear for 20442, 17836 71
24952 Beater for 20442, 17836 2 24990 Roller for 20442, 17836 38-3 25027 Gasket for 20442, 17836 72
24953 Wire Whip for 20442, 17836 3 24880 Spring for 20442, 17836 38-4 25028 Plug 1 for 20442, 17836 73
24954 Safety Guard for 20442, 17836 4 24992 Gear for 20442, 17836 39 25029 Nut for 20442, 17836 74
24955 Bowl for 20442, 17836 5 24901 Bushing for 20442, 17836 40 25030 Spring Washers for 20442, 17836 75
24956 Top Cover for 20442, 17836 6 24994 Sleeve for 20442, 17836 41 25084 Bearing for 20442, 17836 76
24960 Shifting Yoke for 20442, 17836 7-10 24995 Gear for 20442, 17836 42 25032 Shaft Worm Gear for 20442, 17836 77
24863 Cam-Gear Shifter for 20442, 17836 11 24996 Gasket for 20442, 17836 43 25008 Key for 20442, 17836 78
24864 Plate-Shifter Index for 20442, 17836 12 24997 Bearing for 20442, 17836 44 25034 Circlips for Shaft for 20442, 17836 79
24963 Handle-Shifter for 20442, 17836 13 24998 Bushing for 20442, 17836 45 25035 Circlips for Shaft for 20442, 17836 80
24964 Handle Set for 20442, 17836 14 24999 Oil Seal for 20442, 17836 46 25036 Plug 2 for 20442, 17836 81
24965 Turnset for 20442, 17836 15 25000 Body Housing for 20442, 17836 47 25037 Motor for 20442, 17836 82
24966 Speed Handle for 20442, 17836 16 25001 Bowl Holddown for 20442, 17836 48 25038 Rubber for 20442, 17836 83
24967 Plug for 20442, 17836 17 25002 Support for 20442, 17836 49 24922 Green Button Round for 20442, 17836 84
24968 Attachment Hub for 20442, 17836 18 25003 Spacer for 20442, 17836 50 25040
24870 Tighten Handle for 20442, 17836 19 25004 Nut for 20442, 17836 51 25041
24871 Ring for 20442, 17836 20 25005 Base for 20442, 17836 52 25042 Crank Lever for 20442, 17836 86
24971 Gear for 20442, 17836 21 25006 Bearing for 20442, 17836 53 25043 Handle-Shifter for 20442, 17836 87
24972 Hood Ring for 20442, 17836 22 25007
24973 Circlips for Shaft Q for 20442, 17836 23 25008 Key for 20442, 17836 55 24938 Spacer for 20442, 17836 89
24974 Planetary Gear for 20442, 17836 24 25009 Circlips for Shaft for 20442, 17836 56 25046 Spring for 20442, 17836 90
24975 Operating Shelf for 20442, 17836 25 25010 Gear for 20442, 17836 57 25047 Spacer for 20442, 17836 91
24905 Bearing 6205 for 20442, 17836 26 25011 Bushing for 20442, 17836 58 15559 Angle Iron for 20442, 17836 92
24977 Oil Seal for 20442, 17836 27 25012 Front Housing for 20442, 17836 59 25049 Rail Guide Plater for 20442, 17836 93
24978 Pin for 20442, 17836 28 25013 Worm Wheel-New for 20442, 17836 60 25050
24979 Working Shaft for 20442, 17836 29 25015 Mark for 20442, 17836 61 16323 Run Capacitor 40uf for 20442, 17836
24980 Declutch Shift Shaft Q for 20442, 17836 30 25016 Case for 20442, 17836 62 25052 Start Capacitor 400 UF for 20442, 17836
24939 Spacer for 20442, 17836 31 25017 Back Cover for 20442, 17836 63 25053 Contactor-Relay for 20442, 17836
24982 Main Shaft for 20442, 17836 32 25018 Internal Gear for 20442, 17836 64 25054 Power Cord for 20442, 17836
24883 Nut for 20442, 17836 33 25019 Screw for 20442, 17836 65 25055 Reset-Overload Switch for 20442, 17836
24984 Top Batter Valve Cap for 20442, 17836 34 25020 Seal Up Ring for 20442, 17836 66 24950 Rear Cover Screws for 20442, 17836
24985 Plug Cover (Steel) for 20442, 17836 35 25021 Gear Shaft for 20442, 17836 67 24947
25070 Bearing 6204 for 20442, 17836 36 25022 Gear for 20442, 17836 68 25152 Timer Knob for 20442, 17836
24987 Spacer-Lower for 20442, 17836 37 25023 Bushing for 20442, 17836 69
24988 Big Gear for 20442, 17836 38-1 25024
Transmission Shaft Support for 20442,
17836
Brass Gear-New Style 28 Teeth for
20442, 17836
54 25044 Connecting Rod for 20442, 17836 88
70
Red Stop Button without Timer CSA for
20442, 17836
On/Off Switch/Button with Timer for
20442, 17836
Run Capacitor 60 UF - New for 20442,
17836
Safety Guard-Bowl Switch for 20442,
17836
85
85
20
Page 21
Model MX-CN-0010-G 20467
Electrical Schematics
No. Name Model Specs QTY Remark
1 Motor 110V 60Hz / 1725rpm / 1PH 0.4Kw 1
2 Micro Switch V-152-1C25 250V 10A 2
3 Contact Switch CJX2-0910 Ac110V 60Hz 1
4 Start Button SPL63 250V 10A 1 Green
5 Stop Button SPL63 250V 10A 1 Red
6 Overload Protector Ac125/250V 15A 1 KUOYUH
7 Start Capacitor 20uF 125VAC 1 C1
8 Running Capacitor CBB60 100uF 300VAC 1 C2
21
Page 22
Electrical Schematics
Model MX-CN-0020-G 20441
No. Name Model Specs QTY Remark
1 Motor 110V 60Hz / 1725rpm / 1PH 1.1Kw 1
2 Micro Switch V-152-1C25 250V 10A 2
3 Contact Switch CN--11 Ac110V 60Hz 1
4 Start Button SPL63 250V 10A 1 Green
5 Stop Button SPL63 250V 10A 1 Red
6 Overload Capacitor Ac125/250V 15A 1 KUOYUH
7 Start Capacitor 300MF 125VAC 1 C1
8 Running Capacitor CBB60 40uF 300VAC 1 C2
22
Page 23
Model MX-CN-0020-T 17835
Electrical Schematics
No. Name Model Specs QTY Remark
1 Motor 110V 60Hz / 1PH 1.1Kw 1
2 Micro Switch V-152-1C25 250V 10A 2
3 Contact Switch CN--11 Ac110V 60Hz 1
4 Start Button SPL63 250V 10A 1 Green
5 Stop Button SPL63 250V 10A 1 Red
6 Overload Capacitor Ac125/250V 15A 1 KUOYUH
7 Start Capacitor 300MF 125VAC 1 C1
8 Running Capacitor CBB60 40uF 300VAC 1 C2
9 Timer DKG-5A 250V 16A 1 T
23
Page 24
Electrical Schematics
Model MX-CN-0030-G 20442
No. Name Model Specs QTY Remark
1 Motor 110V 60Hz / 1725rpm / 1PH 1.8Kw 1
2 Micro Switch V-152-1C25 250V 10A 2
3 Contact Switch CN--11 Ac110V 60Hz 1
4 Start Button SPL63 250V 10A 1 Green
5 Stop Button SPL63 250V 10A 1 Red
6 Overload Protector Ac125/250V 20A 1 KUOYUH
7 Start Capacitor 4000pF 125VAC 1 C1
8 Running Capacitor CBB60 60uF 300VAC 1 C2
24
Page 25
Model MX-CN-0030-T 17836
Electrical Schematics
No. Name Model Specs QTY Remark
1 Motor 110V 60Hz / 1725rpm / 1PH 1.8Kw 1
2 Micro Switch V-152-1C25 250V 10A 2
3 Contact Switch CN--11 Ac110V 60Hz 1
4 Start Button SPL63 250V 10A 1 Green
5 Stop Button SPL63 250V 10A 1 Red
6 Overload Capacitor Ac125/250V 20A 1 KUOYUH
7 Start Capacitor 4000pF 125VAC 1 C1
8 Running Capacitor CBB60 60uF 300VAC 1 C2
9 Timer DKG-5A 250V 16A 1 T
25
Page 26
Electrical Schematics
Model MX-CN-0020-G 20441
Model MX-CN-0020-T 17835
Model MX-CN-0030-G 20442
Model MX-CN-0030-T 17836
26
Page 27
Warranty Registration
Thank you for purchasing an Omcan product. To register your warranty for this product, complete the information below, tear off the card at
the perforation and then send to the address specied below. You can also register online by visiting:
Merci d’avoir acheté un produit Omcan. Pour enregistrer votre garantie pour ce produit, complétez les informations ci-dessous, détachez la
carte au niveau de la perforation, puis l’envoyer à l’adresse spécié ci-dessous. Vous pouvez également vous inscrire en ligne en visitant:
Gracias por comprar un producto Omcan usted. Para registrar su garantía para este producto, complete la información a continuación,
cortar la tarjeta en la perforación y luego enviarlo a la dirección indicada a continuación. También puede registrarse en línea en:
https://omcan.com/warranty-registration/
For mailing in Canada
Pour postale au Canada
Por correo en Canadá
OMCAN
PRODUCT WARRANTY REGISTRATION
3115 Pepper Mill Court,
Mississauga, Ontario
Canada, L5L 4X5
PRODUCT WARRANTY REGISTRATION
4450 Witmer Industrial Estates, Unit 4,
For mailing in the US
Pour diffusion aux États-Unis
Por correo en los EE.UU.
OMCAN
Niagara Falls, New York
USA, 14305
or email to: [email protected]
Purchaser’s Information
Name: Company Name:
Address:
Telephone:
City: Province or State: Postal or Zip: Email Address:
Country: Type of Company:
Restaurant Bakery Deli
Dealer from which Purchased: Butcher Supermarket Caterer
Dealer City: Dealer Province or State: Institution (specify):
Invoice: Other (specify):
Model Name: Model Number: Serial Number:
Machine Description:
Date of Purchase (MM/DD/YYYY): Date of Installation (MM/DD/YYYY):
Would you like to extend the warranty? Yes No
Thank you for choosing Omcan | Merci d’avoir choisi Omcan | Gracias por elegir Omcan
27
Page 28
Since 1951 Omcan has grown to become a leading distributor of equipment and supplies to the North
American food service industry. Our success over these many years can be attributed to our commitment
to strengthen and develop new and existing relationships with our valued customers and manufacturers.
Today with partners in North America, Europe, Asia and South America, we continually work to improve
and grow the company. We strive to offer customers exceptional value through our qualied local sales
and service representatives who provide convenient access to over 6,500 globally sourced products.
Depuis 1951 Omcan a grandi pour devenir un des “leaders” de la distribution des équipements et
matériel pour l’industrie des services alimentaires en Amérique du Nord. Notre succès au cours de ces
nombreuses années peut être attribué à notre engagement à renforcer et à développer de nouvelles
et existantes relations avec nos clients et les fabricants de valeur. Aujourd’hui avec des partenaires en
Amérique du Nord, Europe, Asie et Amérique du Sud, nous travaillons continuellement à améliorer et
développer l’entreprise. Nous nous efforçons d’offrir à nos clients une valeur exceptionnelle grâce à
nos ventes locales qualiées et des représentants de service qui offrent un accès facile à plus de 6500
produits provenant du monde entier.
Desde 1951 Omcan ha crecido hasta convertirse en un líder en la distribución de equipos y suministros
de alimentos en América del Norte industria de servicios. Nuestro éxito en estos años se puede atribuir
a nuestro compromiso de fortalecer y desarrollar nuevas relaciones existentes con nuestros valiosos
clientes y fabricantes. Hoy con socios de América del Norte, Europa, Asia y América del Sur, que trabajan
continuamente para mejorar y crecer la empresa. Nos esforzamos por ofrecer a nuestros clientes valor
excepcional a través de nuestro local de ventas y representantes de los servicios que proporcionan un
fácil acceso a más de 6,500 productos con origen a nivel mundial.
Loading...