Olympus PFL-01 User Manual
Instruction Manual
Waterproof Case
PFL-01
For the electronic flash
FL-20
■ Thank you for buying the Underwater Case PFL-01.
■ Please read this instruction manual carefully and use the product safely
and correctly.
■ Please keep this instruction manual for reference after reading it.
■ Wrong use may cause damage to the flash on the inside from water
leakage, and repair may not be possible.
■ Before use, perform an advance check as described in this manual.
Disclaimer
WARNING
CAUTION
WARNING
●
Unauthorised copying of this manual in part or in full, except for private
use, is prohibited. Unauthorised reproduction is strictly prohibited.
● OLYMPUS CORPORATION shall not be responsible in any way
for lost profits or any claims by third parties in case of any damage
occurring from incorrect use of this product.
● OLYMPUS CORPORATION shall not be responsible in any way
for damage, lost profits, etc. caused by the loss of image data due
to defects, disassembly, repair or modification of this product by
people, other than third parties specifically authorised by
OLYMPUS CORPORATION or for other reasons.
Please read the following before using the product
● This product has been precision-crafted from high quality
polycarbonate. When used correctly, it lets you take photographs
safely up to a water pressure equivalent to a depth of 40 metres.
● To ensure correct and safe use of the case, please read all
instructions on handling and carrying out the system check as well
as care, maintenance and storage of the case.
● OLYMPUS CORPORATION shall in no way be responsible for
damage caused by water to the flash contained in the case.
● OLYMPUS CORPORATION shall not pay any compensation for
accidents (injuries or material damage) that may occur during the use
of this product.
● The electronic flash cannot be used in AUTO mode when it is
inserted in this case.
● A commercially available bracket arm is required to use this
product in combination with the PT-020.
For safe use
This instruction manual uses various pictographs for correct use of
the product and to prevent danger to the user and other persons as
well as property damage. These pictographs and their meanings are
shown below.
This indicates contents for which the possibility of
human death or severe injury in case of handling under
disregard of this indication can be assumed.
This indicates contents for which the possibility of
human injury or the possibility of material damage in
case of handling under disregard of this indication can
be assumed.
1. Keep this product out of the reach of babies, infants, and children.
There is the possibility of occurrence of the following types of
accidents.
Injury by dropping onto the body from a height.
Injury from parts of the body getting caught in parts which open
and close.
Swallowing of small parts. Please consult a physician immediately
if any parts have been swallowed.
Triggering of the flash in front of the eyes may cause permanent
vision impairment etc.
2. Never store this product with an electronic flash with batteries
inside. Battery leakage could result in a fire or an explosion.
3. If water comes into contact with the electronic flash inside this
product, remove the batteries from the flash immediately.
Otherwise, hydrogen gas could be produced, which could lead to a
fire or an explosion.
4. This product is made of resin. There is the possibility that injuries
may be caused when it becomes broken because of strong impact
with a rock or other hard objects. Please handle with sufficient care.
5. The silica gel and the grease for silicone O-rings for this product
are not edible.
CAUTION
1. Do not disassemble or modify this product. This may cause water
leakage or trouble. In case of disassembly or modification by
persons other than those appointed by OLYMPUS CORPORATION,
the guarantee shall not apply.
2. Do not place this product at locations with abnormally high or
abnormally low temperatures or at locations with extreme
temperature changes. The product may deteriorate.
3. Opening and closing at locations with much sand, dust, or dirt may
impair the waterproof characteristic and cause water leakage. This
should be avoided.
4. This product is suitable for use at water pressures equivalent to
depths of up to 40 meters. Please note that diving at depths
greater than 40 meters may result in deformation or damage to this
product, as well as to the camera and lens. In this case, water
penetration may occur.
E-2E-1
5. Rough handling, such as jumping into the water with the case in
your hand or in an outside pocket or throwing the case into the
water could lead to water penetration. Please always take care
when using the case.
6. If the electronic flash contained in the case gets wet, wipe off all
moisture immediately and check the flash is working correctly.
7. Before traveling by air, please make sure you remove the O-rings,
otherwise the difference in air pressure may make it impossible to
open the case.
8. To ensure safe and trouble-free handling and operation of the
electronic flash in this product, please read the flash’s instruction
manual carefully.
9. When sealing this product, please take care to ensure no foreign
matter such as sand, dirt or hair is on the O-rings or contact
surfaces.
10.
Before storing this product, always be sure to take out the flash.
11.
When using this product, do not fire the flash at close range to a
person or animal.
For Prevention of Water Leakage Accidents
If water gets inside this product during use, irreparable damage may
be caused to the electronic flash inside the case. Please note the
following points.
1. When sealing this product, make sure that no hairs, fibers, sand
particles or other foreign matter stick not only to the O-ring, but
also to the contact surface. Even a single hair or a single grain of
sand may cause water leakage. Please check with special care.
2. The O-ring is a consumption product. Please replace it at least
Examples for foreign matter sticking to the O-ring
Batteries
● To supply power to the electronic flash, we recommend you use
two LR6 alkaline batteries, two lithium batteries, two Ni-Mn
batteries, two Ni-Mh batteries or two Ni-Cd batteries.
● Keep the batteries’ contacts away from damp and humidity to avoid
impairing performance and/or causing an accident.
● For other battery handling precautions, please read the relevant
sections in the electronic flash’s instruction manual.
Hair Fibers Grains of sand
once a year by new one. Also perform maintenance for every use.
3. Deterioration of the O-ring will progress according to the use
conditions and the storage conditions. Immediately replace the O-ring
by a new one if it is damaged, shows cracks, or has lost its elasticity.
4. At the time of O-ring maintenance, clean the inside of the O-ring
groove and confirm the absence of dirt, dust, sand, and other
foreign matter.
5. Apply the specified silicone O-ring grease to the O-ring.
6. The waterproof function is not effective when the O-ring is not
installed correctly. When installing the O-ring, take care that it does
not project from the groove and that it is not twisted. Also, when
sealing the Case, close the lid after confirming that the O-ring has
not come out of the groove.
7. This product is an airtight construction made of plastic (polycarbonate).
When it is left for a long time in a car, on a boat, at the beach, or at
other places reaching a high temperature, or when it is subjected for a
long time to uneven external force, it may be deformed and the
waterproof function may be lost. Pay sufficient attention to temperature
control. Also do not place heavy objects onto the product during
storage or transport, and avoid unreasonable storage.
8. When the O-ring contact surface is pressed strongly from the
E-4E-3
outside of the Case, or when the Case is twisted, the waterproof
function may be lost. Take care not to exert excessive force.
9. Please be sure to perform the advance test and the final test each
time before using the case.
10
.If you see any drops of water or any other signs of water
penetration during use, stop the dive immediately. Carefully dry
from the flash and waterproof case, and then perform the “Final
System Check” and confirm whether any water actually penetrated
this product.
Handling the Product
● Use or storage of the product at the following locations may cause
defective operation, defects, trouble, damage, fire, internal
clouding, or water leakage. Always avoid these locations.
Places where high temperatures exist, such as in direct sunlight, in
a closed vehicle, etc., and/or where extreme differences in
temperatures exist.
Places where there is a lot of dust.
Places where there are open fires.
Places subject to vibrations.
Places where volatile chemicals are stored or used.
water deeper than 40 meters.
● This product is made of polycarbonate resin with excellent impact
resistance, but it may be damaged by scraping against rocks etc. It
also may break when it hits hard objects or is dropped.
● This product is not intended as a case to protect the internal flash
from heavy knocks. If the case is subjected to a heavy knock or
significant pressure, the flash inside may be severely damaged.
● When this product is not used for a long time, the O-rings may
deteriorate, diminishing its waterproof properties. Therefore, please
use the case only after first performing the first and final system
checks described in this instruction manual.
● Do not apply excessive force to the arm mount and underwater
TTL cable connector.
●
The range of the flash underwater may be lower than on land depending
on the conditions at the time of shooting (clarity of the water, suspended
matter, etc.). Be sure to check the image before actual shooting.
●
Do not use the following chemicals for cleaning, corrosion prevention,
prevention of fogging, repair or other purposes. When these are used
for the Case directly or indirectly (with the chemicals in vaporized state),
they may cause cracking under high pressure or other problems.
Chemicals which cannot be used
Volatile organic solvents,
chemical detergents
Anticorrosion agent
Commercial defogging
agents
Grease other than specified
silicone grease
Adhesive
Explanation
Do not clean the Case with alcohol, gasoline, thinner
or other volatile organic solvents or with chemical
detergents etc. Pure water or lukewarm water is
sufficient.
Do not use anticorrosion agents. The metal parts use
stainless steel or brass, and washing with pure water
is sufficient.
Do not use commercial defogging agents. Always
use the specified desiccant silica gel.
Use only the specified silicone grease for the silicone
O-ring, as otherwise the O-ring surface may
deteriorate and water leakage may be caused.
Do not use adhesive for repairs or other purposes.
When repair is required, please contact a dealer or a
service station of our company.
● Do not perform operations other than specified in this instruction
manual, do not remove or modify parts other than specified, and do
not use parts other than specified.
Any troubles in taking pictures or with the equipment resulting from
the above actions shall be outside the guarantee.
● OLYMPUS CORPORATION does not assume any liability for
damage to the flash caused by water penetration.
● OLYMPUS CORPORATION shall not pay any compensation for
accidents (injury or material damage) at the time of use.
E-6E-5
Contents
Disclaimer⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-1
Please read the following before using the product ⋯⋯⋯⋯⋯E-1
For safe use ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-1
Batteries ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-3
For Prevention of Water Leakage Accidents ⋯⋯⋯⋯⋯⋯⋯⋯E-4
Handling the Product ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-5
Contents ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-7-8
1. Preparations ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-9
Checking the contents of the package ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-9
Names of the parts ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-10
Preparing the case ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-11
Attaching/removing/the diffuser plate ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-11
Connection to the camera case ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-12
1) Connecting the underwater TTL cable ⋯⋯⋯⋯⋯⋯⋯⋯E-12
2) Connecting the hot shoe cable ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-13
3) Mounting on an arm ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-14
2. Advance Check of the Case ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-15
Advance test before use ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-15
Advance Test ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-15
3. Insertion of the electronic flash ⋯⋯⋯⋯⋯⋯⋯⋯E-16
Checking the electronic flash ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-16
Checking the Batteries ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-16
Inserting in the case ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-16
Which electronic flashes can be used? ⋯⋯⋯⋯⋯⋯⋯⋯⋯E-16
Opening the case ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-17
Inserting the flash ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-17
Insertion of silica gel ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-18
Check the loading status ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-19
Seal the Case ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-19
Perform the final check ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-20
Visual inspection ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-20
Setting she flush power to ON and OFF ⋯⋯⋯⋯⋯⋯⋯⋯E-20
Final Test ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-21
4. Taking photos underwater ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-22
Setting the flash mode ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-22
Underwater TTL AUTO shooting ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-22
Underwater MANUAL shooting ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-22
5. Handling after use ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-23
Wipe off any waterdrop ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-23
Removing the electronic flash⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-24
Cleaning the case with pure water⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-24
Disconnecting the TTL cable ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-25
Drying the case and TTL cable ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-25
6. Maintaining the Waterproof Function ⋯⋯⋯⋯⋯E-26
Remove the O-ring. ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-26
Remove any sand, dirt, etc. ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-26
Install the O-ring. ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-27
How to Apply Grease to the O-ring ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-27
Replace consumable products. ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-28
7. Appendix⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-29
Q & A on the use of the PFL-01 ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-29
After-sale Service ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-34
Specifications ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-35
E-8E-7
1. Preparations
*① Mode dial
② Buckle hook
*③ Test button
④ Buckle open/close lever
⑤ Light-emitting window
⑥ Arm mount
⑦ Diffuser plate strap
⑧ Diffuser plate
⑨
Underwater TTL cable connector
⑩ Hot shoe
⑪ Underwater TTL cable connector cap
⑫ Grease for silicone O-ring (white cap)
⑬ Silica gel
⑭ O-ring removal pick
⑮ Buckle opener
⑯ Arm attaching adapter
⑰ O-ring (POL-201A)
⑱ O-ring (POL-201B)
!
保証書
WARRANTY
本保証書は、本記載内容で無料修理を行うことをお約束するものです。
お買い上げの日から下記期間中、万一故障が発生した場合は、本契約書を添付ご持参の上
お買い上げ販売店、または当社サービスステーションにご依頼ください。
本保証書は日本において有効です。
Thisisalimitedwarrantyfor
1yearfromyourdateof
purchase.Usefulonlyin
Japan.
期 間
お買上げ
本体1年間
年 月 日
お客様
Customer
販売店
Dealer's
nameand
address
住所 Address
氏名 Name 性別（男・女）、年齢（ 才）
様
TEL ( )
〔必ず店名印を押してください。〕
JAPAN
品名
防水・防塵
プロテクタ
型名
Model
SerialNO.
保証責任者
保証履行者
〒192-0032 東京都八王子市石川町2951
お問い合せ先/サービスステーション
03（3292）1931
（販売店控え）
取扱説明書
防水プロテクタ
PFL-01
■このたびは、防水プロテクタPFL-01をお買上げいただき、ありがとうござ
います。
■この説明書をよくお読みのうえ、安全に正しくお使いください。また、この
説明書はお読みになった後、必ず保管してください。
■誤った使い方をされると水漏れにより中のフラッシュが破損し、修理不能
になる場合があります。
■ご使用前には、この説明書に従い、必ず事前チェックを実施してください。
エレクトロニックフラッシュ
FL-20用
"# $$%
& &
$$%
&
&
' #
'
&
Check the contents of the package.
Check that all accessories are in the box.
Contact your dealer if accessories should be missing or damaged.
Names of the parts
Note :
The case parts marked with an asterisk (*) correspond to functions
on the electronic flash. Consequently, operation of these parts
activates the corresponding functions in the flash. For details on
these functions, refer to the electronic flash’s instruction manual.
E-10E-9
Loading...