Page 1
TO: SCOP SA
MR.
ATTN:
PIRTINAUD
/
MR.
FARGE
OCTOBER
2,
1985,
SUBJECT: B2-TTR ALIGNMENT
Sorry for delay
procedure how to align.
last.
**
PLEASE FOLLOW FROM No 1. TO 11. OF STEPS.
in
reply of your request alignment of B2-TTR,
Here enclosed
Please study and refer to my idea of solution
-
-
~nc!n
tiont3cl
1
6.
~B2834 (BODY) ASSEMBLY
Adjust Center;
Pupil
orfoculty;
;
1 . LP0653 CENTERING
CT(KN0029) with Adapter & 2-cross
Tolerance; 1/3 Div. of CT(Sca1e)
KN0015 Centering OB
80
KN0016
Tube length /B
hair
8
B2kC0401 Tolerance ; As close as 0
It
8
B2KC0401 Tolerance;
Tolerance
;
20
%
ON.
-
Page 2
7.
B2-BI Assembly;
Make
of optical condition temporary.
8.
GEAR
Adjust inclination of image.
Assemble gear and check inclination of image
9.
TENSION ADJUSTMENT INCLING
Assemble
Tolerance; North to South
After adjusted, Faston set screws of
10.
sure the ablty of align
UNIT
INCLINATION
ASSEMBLY
A82835
temporary & adjust tension watching the center of
OF
IMARGE
CHECK
01
unit and
6009
to
12009,
AB2835.
AB2834..
South
And set it on the best
;
20'
Tolerance
to
Morth Under 2500g
(Sec)
BI
stay.
positil
Tolerance;
11.
ASSEMBLE
12.
02-BI
*PLease refer to
Tolerance of Parfoculty;
Tolerance of Centering
13.
ASSEMBLE
***
NOTE
I
belive the difficulty of
8,
***
PHOTO
ALL
ALL
(SIMPLE
20'
(Sec)
2
Dig. at OC-pin position.
(
EXCEPT
TUBE
B2-BI(TR)
(END)
WAY
KN0004,
BI
8,
PHOTO TUBE)
ADJUSTMENT
Adjustment inRepair Manual BH2.
*
0.1
;
0.2
0.4
"Another side
OF ALIGNMENT)
TTR
alignment
Inclination checker and
mm
with
BI(Right Side) and Photo.
mm
at OC (North, South & outside)
mm
at
KW16
OC
(Inside)
must
is
Image erecter part,
(or Short OB type
be
setted
BH2
-
0
if
model,
K~0007)
you touch
it without knowing alignment,
without Jig &Tool. Here mentioned easier way without touching Imarge erecter
part is as follows;
1.
ALIGN
EXSIT
PUPIL
,F>
:
Incline Bi unit and find the best position. and then,
put tin foil or washer into the space to hold the angle
eccentric movement will show up and hard to
realign
a"/)\
,--.
,,C
North and South
East and West
,
I
Page 3
2.
ALIGN CENTER
*"
In case, Still
will repair and return to you.
We
are at your service at all times.
Slide 82-BI unit and bring eyepiece cross to OB(KN0015)
:
(KN0005)cross, keeping the angle of01 unit for Exsit pupil
TTR
io out of tolerance, Please return it to Hamburg, We
\L
The special JIG
8
TOOL
are orderd to
I
or
O/T.
I
am
looking forward to hearing
Best regards
T.
Imai
good news from you
Loading...