OLD TOWN OAK Monterey Crib Instructions Manual

Monterey Crib

Assembly Instructions

Model#
Serial#

WARNING:

Failure to follow these warnings could result in serious injury or death.

1.

Never place additional padding under an infant.

2. Read and familiarize yourself with all instructions before assembling crib and keep instruction for future use. DO NOT THROW THE

3. DO NOT use crib if any parts are missing, broken or cracked. Before placing child in a previously used crib, inspect the crib for

4. Strangulation Hazard: Strings can cause strangulation! Do not place items with a string around a child’s neck, such as hood strings

5. To help prevent strangulation tighten all fasteners. A child can trap parts of the body or clothing on loose fasteners.

6. DO NOT place crib near window where cords from blinds or drapes may strangle a child.

7. NEVER adjust spring level while baby is in the crib.

8. When child is able to pull to a standing position, set mattress to lowest position and remove bumper pads and large toys that could

9. DO NOT use a water mattress with this crib.

10. Crib should be inspected periodically to be sure it is being properly used and maintained. Rough use and excessive moving of

11. Articles with sharp edges or pointed ends should be kept away from the crib.

12. The use of furniture wax and polish should be avoided. The surface with which the baby can come in contact should be wiped clean

13. This crib should be used as a sleeping place for infants-not as a cage or playpen for active children.

14. When child is able to climb out or reaches the height of 35 inches, the crib shall no longer be used. No two children are alike- and

15. NEVER use shipping or other bags as mattress covers, since these may cause suffocation.

16. When storing crib, carefully package all original parts to protect from loss or damage, and store all parts together.

17. Infants can suffocate in gaps between crib sides and a mattress that is too small.

18. To avoid head injury, DO NOT allow child to play underneath crib.

19. To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their backs to sleep, unless otherwise advised by

20. Follow warnings on all products in a crib.

WARNING:

INSTRUCTION BOOKLET AWAY.

broken or bent brackets, loose joints, missing parts or sharp edges. Ask your dealer or write to Old Town Oak, LLC for replacement
parts and an instruction sheet. Do not substitute parts, even as a temporary measure.

or pacier cords. Do not suspend strings over a crib or attach strings to toys.

serve as steps to climb out.

the crib can cause some bolts to loosen. Loose bolts will cause parts failure and could cause a safety hazard. To ensure safety
standards are maintained, crib should be properly assembled and used.

using a damp cloth and a small amount of mild soap. DO NOT use strong detergents as they may be an irritant to the baby’s skin. If

renishing, use a non-toxic nish specied for children’s products.

as the variance in children is great with respect to height, weight, agility and temperament- and as there is no certain age at which
a child learns to stand or develops the desire or ability to climb out of it’s crib- manufacturers of this crib cannot recommend a given
age at which your child will have out-grown his or her crib.

your physician.

Infants can suffocate on soft bedding. Never add a pillow or comforter.

21.

CAUTION: ANY MATTRESS USED IN THIS

CRIB MUST BE AT LEAST 27¼" BY 51 /" WITH A

5

8

THICKNESS NOT EXCEEDING 6 INCHES.

OLD TOWN OAK LLC., Marlin and Marilyn Miller • 9785 W. 700 S., Topeka, IN 46571 • ph: [phone] • fax: [phone]

Step 1

Lock Washers and

¼" x 2½"

Connector Bolt

FIGURE 1

InstructIons for AssemblIng monterey crIb

- Figure 1 -

Attach small end panels (A) to posts (D)

and with lock washers and two ¼" x 2½"

connector bolts and Attach (E) to (A) with

lock washers and two ½'' x 3''. Turn connector

bolts snug. Top of short post (D) should be

flush with top of end panel (A). *Make sure

label is visible on the outside of the crib.

Lock Washers and

¼” x 3"

Connector Bolt

Do not over tighten!

Tools Needed:

(8) Lock

Washer

(A)

Short Post (D)

End Panel

2 pcs.

Label

- Figure 2 -

Attach small end panels (A) to posts (D)

and with lock washers and two ¼" x 2½"

connector bolts and Attach (E) to (A) with lock

washers and two ½'' x 3''. Turn connector bolts

snug. Top of short post (D) should be flush

with top of end panel (A). *Make sure label is

visible on the outside of the crib.

Do not over tighten!

Step 2

InstructIons for AssemblIng monterey crIb

Attach posts (E, F) to ends of large back panel (B) with

lock washers and four ¼" x 4" connector bolts using

allen wrench provided. Connector bolts screw into

metal inserts in ends of panels. Turn connector bolts

snug. Do not over tighten! Top of long post (E & F)

Long Post (E)

Lock Washers and

¼” x 3"

Connector Bolt

Long Post (E)

Label

FIGURE 1

(A)

End Panel

2 pcs.

should be flush with top of back panel (B).

Lock

Washers and

¼" x 2½"
Connector

Bolt

Short Post (D)

Allen Wrench

(4) ¼" x 2½" Connector Bolt

(4) ¼" x 3" Connector Bolt

Tools Needed:

Lock Washers and

¼" x 4"

Connector Bolt

Long Post (E)

(B)

Back Panel

Long Post (F)

Lock Washers and

¼" x 4"

Connector Bolt

Allen Wrench

(4) ¼" x 4" Connector Bolt

(4) Lock

Washer