Oldsmobile CUTLASS 1999 Owner Manual

The 1999 Oldsmobile Cutlass Owner’s Manual

yellowblue

1-1 Seats and Restraint Systems

This section tells you how to use your seats and safety belts properly. It also explains the “SRS” system.

2-1 Features and Controls

This section explains how to start and operate your vehicle.

3-1 Comfort Controls and Audio Systems

This section tells you how to adjust the ventilation and comfort controls and how to operate your audio system.

4-1 Your Driving and the Road

Here you’ll find helpful information and tips about the road and how to drive under different conditions.

5-1 Problems on the Road

This section tells you what to do if you have a problem while driving, such as a flat tire or overheated engine, etc.

6-1 Service and Appearance Care

Here the manual tells you how to keep your vehicle running properly and looking good.

7-1 Maintenance Schedule

This section tells you when to perform vehicle maintenance and what fluids and lubricants to use.

8-1 Customer Assistance Information

This section tells you how to contact Oldsmobile for assistance and how to get service and owner publications.
It also gives you information on “Reporting Safety Defects” on page 8

9-1 Index

Here’s an alphabetical listing of almost every subject in this manual. You can use it to quickly find
something you want to read.

-9.

i

GENERAL MOTORS, GM, the GM Emblem,
OLDSMOBILE, the OLDSMOBILE Rocket Emblem
are registered trademarks and the name CUTLASS is a
trademark of General Motors Corporation.

This manual includes the latest information at the time
it was printed. We reserve the right to make changes in
the product after that time without further notice.

Please keep this manual in your vehicle, so it will be
there if you ever need it when you’re on the road. If you
sell the vehicle, please leave this manual in it so the new
owner can use it.

yellowblue

We support voluntary
technician certification.

How to Use this Manual

Many people read their owner’s manual from beginning
to end when they first receive their new vehicle. If you
do this, it will help you learn about the features and
controls for your vehicle. In this manual, you’ll find
that pictures and words work together to explain
things quickly.

Litho in U.S.A.
Part No. 22600397 B First Edition All Rights Reserved

E

Copyright General Motors Corporation 1998

ii

yellowblue

Index

A good place to look for what you need is the Index in
back of the manual. It’s an alphabetical list of what’s in
the manual, and the page number where you’ll find it.

Safety Warnings and Symbols

You will find a number of safety cautions in this book.
We use a box and the word CAUTION to tell you
about things that could hurt you if you were to ignore
the warning.

CAUTION:

These mean there is something that could hurt
you or other people.

In the caution area, we tell you what the hazard is. Then
we tell you what to do to help avoid or reduce the
hazard. Please read these cautions. If you don’t, you or
others could be hurt.

You will also find a circle
with a slash through it in
this book. This safety
symbol means “Don’t,”
“Don’t do this” or “Don’t
let this happen.”

iii

yellowblue

Vehicle Damage Warnings

Also in this book you will find these notices:

NOTICE:

These mean there is something that could
damage your vehicle.

In the notice area, we tell you about something that can
damage your vehicle. Many times, this damage would
not be covered by your warranty, and it could be costly.
But the notice will tell you what to do to help avoid
the damage.

When you read other manuals, you might see CAUTION
and NOTICE warnings in different colors or in
different words.

You’ll also see warning labels on your vehicle. They use
the same words, CAUTION or NOTICE.

iv

Vehicle Symbols

These are some of the symbols you may find on your vehicle.

yellowblue

For example,
these symbols
are used on an
original battery:

CAUTION

POSSIBLE

INJURY

PROTECT

EYES BY

SHIELDING

CAUSTIC
BATTERY

ACID COULD

CAUSE

BURNS

AVOID

SPARKS OR

FLAMES

SPARK OR

FLAME

COULD

EXPLODE

BATTERY

These symbols
are important
for you and
your passengers
whenever your
vehicle is
driven:

DOOR LOCK

UNLOCK

FASTEN

SEAT

BELTS

POWER

WINDOW

AIR BAG

These symbols
have to do with
your lamps:

MASTER

LIGHTING

SWITCH

TURN

SIGNALS

PARKING

LAMPS

HAZARD
WARNING
FLASHER

DAYTIME

RUNNING

LAMPS

FOG LAMPS

These symbols
are on some of
your controls:

WINDSHIELD

WIPER

WINDSHIELD

WASHER

WINDSHIELD

DEFROSTER

REAR

WINDOW

DEFOGGER

VENTILATING

FAN

These symbols
are used on
warning and
indicator lights:

ENGINE

COOLANT

TEMP

BATTERY

CHARGING

SYSTEM

BRAKE

COOLANT

ENGINE OIL

PRESSURE

ANTI-LOCK

BRAKES

Here are some
other symbols
you may see:

FUSE

LIGHTER

HORN

SPEAKER

FUEL

v

✍

yellowblue

NOTES

vi

yellowblue

Section 1 Seats and Restraint Systems

Here you’ll find information about the seats in your vehicle and how to use your safety belts properly. You can also
learn about some things you should not do with air bags and safety belts.

1

-2 Seats and Seat Controls

1

-6 Safety Belts: They’re for Everyone

-11 Here Are Questions Many People Ask About

1

Safety Belts

-12 How to Wear Safety Belts Properly

1
1

-12 Driver Position

1

-19 Safety Belt Use During Pregnancy

-20 Right Front Passenger Position

1
1

-20 Supplemental Restraint System (SRS)

-27 Rear Seat Passengers

1

-- and the Answers

-30 Rear Safety Belt Comfort Guides for

1

Children and Small Adults

1-32 Center Passenger Position
1

-34 Children

-37 Child Restraints

1
1

-49 Larger Children

1

-52 Safety Belt Extender

-52 Checking Your Restraint Systems

1
1

-52 Replacing Restraint System Parts

After a Crash

1-

1-1

Seats and Seat Controls

This section tells you about the seats -- how to
adjust them
head restraints.

-- and also about reclining seatbacks and

Manual Seats

CAUTION:

You can lose control of the vehicle if you try to
adjust a manual driver’s seat while the vehicle is
moving. The sudden movement could startle and
confuse you, or make you push a pedal when you
don’t want to. Adjust the driver’s seat only when
the vehicle is not moving.

yellowblue

Lift the lever under the front seat to unlock it. Slide the
seat to where you want it. Then release the lever and try
to move the seat with your body, to make sure the seat is
locked into place.

1-2

yellowblue

6-Way Power Seat (If Equipped)

The power seat button is located on the lower left side of
the driver’s seat. This button allows you to move the
seat up, down, forward and backward. It also moves the
front of the seat up or down and the rear of the seat up
or down.

Move the seat higher by lifting and holding the bottom
of the button. Lower the seat by pushing and holding the
top of the button.

T o move the seat forward, push the rear of the button
forward. T o move the seat backward, push the front of
the button rearward.

Raise the front of the seat by lifting and holding the
bottom front end of the button. Lower the front of
the seat by pushing and holding the top front end of
the button.

Raise the rear of the seat by lifting and holding the
bottom rear of the button. Lower the rear of the seat by
pushing and holding the top rear of the button.

1-3

Reclining Front Seatbacks

yellowblue

T o adjust the seatback, lift the lever on the outer side of
the seat and move the seatback to where you want it.
Release the lever and ensure the handle returns to the
original position and the seatback is securely locked.

Pull up on the lever and the seat will go to an
upright position.

1-4

But don’t have a seatback reclined if your vehicle
is moving.

CAUTION:

Sitting in a reclined position when your vehicle is
in motion can be dangerous. Even if you buckle
up, your safety belts can’t do their job when
you’re reclined like this.

The shoulder belt can’t do its job because it
won’t be against your body. Instead, it will be in
front of you. In a crash you could go into it,
receiving neck or other injuries.

The lap belt can’t do its job either. In a crash the
belt could go up over your abdomen. The belt
forces would be there, not at your pelvic bones.
This could cause serious internal injuries.

For proper protection when the vehicle is in
motion, have the seatback upright. Then sit well
back in the seat and wear your safety belt properly.

yellowblue

Head Restraints

Slide the head restraint up or down so that the top of the
restraint is closest to the top of your ears. This position
reduces the chance of a neck injury in a crash.

Rear Seats

Folding Rear Seat

1-5

T o open the folding rear seat, open the trunk and pull
one or both of the tethers located on the left side of the
trunk. The left-hand tether will open the larger side of
the seatback. The right
side of the seatback. Once a tether is pulled, the seatback
can be pushed open through the trunk, or pulled open
from inside the vehicle.

T o close the split folding rear seat, push the seatback up
until you hear a click. Then pull on the seatback to make
sure it is secure.

-hand tether will open the smaller

yellowblue

Safety Belts: They’re for Everyone

This part of the manual tells you how to use safety belts
properly. It also tells you some things you should not do
with safety belts.

And it explains the Supplemental Restraint System
(SRS), or air bag system.

CAUTION:

Don’t let anyone ride where he or she can’t wear
a safety belt properly. If you are in a crash and
you’re not wearing a safety belt, your injuries
can be much worse. You can hit things inside the
vehicle or be ejected from it. You can be seriously
injured or killed. In the same crash, you might
not be if you are buckled up. Always fasten your
safety belt, and check that your passengers’ belts
are fastened properly too.

1-6

CAUTION:

It is extremely dangerous to ride in a cargo area,
inside or outside of a vehicle. In a collision,
people riding in these areas are more likely to be
seriously injured or killed. Do not allow people to
ride in any area of your vehicle that is not
equipped with seats and safety belts. Be sure
everyone in your vehicle is in a seat and using a
safety belt properly.

yellowblue

Your vehicle has a light
that comes on as a reminder
to buckle up. (See “Safety
Belt Reminder Light” in
the Index.)

In most states and Canadian provinces, the law says to
wear safety belts. Here’s why: They work.

You never know if you’ll be in a crash. If you do have a
crash, you don’t know if it will be a bad one.

A few crashes are mild, and some crashes can be so
serious that even buckled up a person wouldn’t survive.
But most crashes are in between. In many of them,
people who buckle up can survive and sometimes walk
away . Without belts they could have been badly hurt
or killed.

After more than 30 years of safety belts in vehicles,
the facts are clear. In most crashes buckling up does
matter ... a lot!

1-7

Why Safety Belts Work

When you ride in or on anything, you go as fast as
it goes.

T ake the simplest vehicle. Suppose it’s just a seat
on wheels.

yellowblue

Put someone on it.

1-8

yellowblue

Get it up to speed. Then stop the vehicle. The rider
doesn’t stop.

The person keeps going until stopped by something.
In a real vehicle, it could be the windshield ...

1-9

or the instrument panel ... or the safety belts!

With safety belts, you slow down as the vehicle does.
You get more time to stop. You stop over more distance,
and your strongest bones take the forces. That’s why
safety belts make such good sense.

yellowblue

1-10

yellowblue

Here Are Questions Many People Ask
About Safety Belts

Won’t I be trapped in the vehicle after an

Q:

accident if I’m wearing a safety belt?

-- and the Answers

A: You could be -- whether you’re wearing a safety

belt or not. But you can unbuckle a safety belt,
even if you’re upside down. And your chance of
being conscious during and after an accident, so
you can unbuckle and get out, is much greater if
you are belted.

Q: If my vehicle has air bags, why should I have to

wear safety belts?

A: Air bags are in many vehicles today and will be in

most of them in the future. But they are
supplemental systems only; so they work with
safety belts
system ever offered for sale has required the use of
safety belts. Even if you’re in a vehicle that has air
bags, you still have to buckle up to get the most
protection. That’s true not only in frontal collisions,
but especially in side and other collisions.

-- not instead of them. Every air bag

Q: If I’m a good driver, and I never drive far from

home, why should I wear safety belts?

A: You may be an excellent driver, but if you’re in an

accident
your passengers can be hurt. Being a good driver
doesn’t protect you from things beyond your
control, such as bad drivers.

Most accidents occur within 25 miles (40 km) of
home. And the greatest number of serious
injuries and deaths occur at speeds of less than
40 mph (65 km/h).

Safety belts are for everyone.

-- even one that isn’t your fault -- you and

1-11

How to Wear Safety Belts Properly

Adults

This part is only for people of adult size.
Be aware that there are special things to know about safety

belts and children. And there are different rules for smaller
children and babies. If a child will be riding in your
vehicle, see the part of this manual called “Children.”
Follow those rules for everyone’s protection.

First, you’ll want to know which restraint systems your
vehicle has.

We’ll start with the driver position.

Driver Position

This part describes the driver’s restraint system.

Lap-Shoulder Belt

The driver has a lap-shoulder belt. Here’s how to wear
it properly.

1. Close and lock the door.

2. Adjust the seat (to see how, see “Seats” in the Index)
so you can sit up straight.

yellowblue

3. Pick up the latch plate and pull the belt across you.
Don’t let it get twisted.

The shoulder belt may lock if you pull the belt across
you very quickly. If this happens, let the belt go back
slightly to unlock it. Then pull the belt across you
more slowly.

4. Push the latch plate into the buckle until it clicks.

1-12

yellowblue

If the belt stops before it reaches the buckle, tilt
the latch plate and keep pulling until you can buckle
the belt.

Pull up on the latch plate to make sure it is secure. If
the belt isn’t long enough, see “Safety Belt
Extender” at the end of this section.

Make sure the release button on the buckle is
positioned so you would be able to unbuckle the
safety belt quickly if you ever had to.

5. T o make the lap part tight, pull down on the buckle
end of the belt as you pull up on the shoulder belt.

1-13

The lap part of the belt should be worn low and snug on
the hips, just touching the thighs. In a crash, this applies
force to the strong pelvic bones. And you’d be less likely
to slide under the lap belt. If you slid under it, the belt
would apply force at your abdomen. This could cause
serious or even fatal injuries. The shoulder belt should go
over the shoulder and across the chest. These parts of the
body are best able to take belt restraining forces.

The safety belt locks if there’s a sudden stop or crash, or
if you pull the belt very quickly out of the retractor.

yellowblue

Shoulder Belt Height Adjuster

Before you begin to drive, move the shoulder belt
adjuster to the height that is right for you.

T o move it down, pushing up on the shoulder belt guide.
and move the height adjuster to the desired position.
You can move the adjuster up just by squeezing the
release button. After you move the adjuster to where
you want it, try to move it down without to make sure it
has locked into position.

1-14

Adjust the height so that the shoulder portion of the belt is
centered on your shoulder. The belt should be away from
your face and neck, but not falling off your shoulder.

yellowblue

CAUTION:

Q: What’s wrong with this?

A: The shoulder belt is too loose. It won’t give nearly

as much protection this way.

You can be seriously hurt if your shoulder belt is
too loose. In a crash, you would move forward
too much, which could increase injury. The
shoulder belt should fit against your body.

1-15

Q: What’s wrong with this?

A: The belt is buckled in the wrong place.

yellowblue

CAUTION:

You can be seriously injured if your belt is
buckled in the wrong place like this. In a crash,
the belt would go up over your abdomen. The
belt forces would be there, not at the pelvic
bones. This could cause serious internal injuries.
Always buckle your belt into the buckle
nearest you.

1-16

Q: What’s wrong with this?

A: The shoulder belt is worn under the arm. It should

be worn over the shoulder at all times.

yellowblue

CAUTION:

You can be seriously injured if you wear the
shoulder belt under your arm. In a crash, your
body would move too far forward, which would
increase the chance of head and neck injury.
Also, the belt would apply too much force to the
ribs, which aren’t as strong as shoulder bones.
You could also severely injure internal organs
like your liver or spleen.

1-17

Q: What’s wrong with this?

A: The belt is twisted across the body.

yellowblue

CAUTION:

You can be seriously injured by a twisted belt. In
a crash, you wouldn’t have the full width of the
belt to spread impact forces. If a belt is twisted,
make it straight so it can work properly, or ask
your dealer to fix it.

1-18

T o unlatch the belt, just push the button on the buckle.
The belt should go back out of the way.

Before you close the door, be sure the belt is out of the
way . If you slam the door on it, you can damage both the
belt and your vehicle.

yellowblue

Safety Belt Use During Pregnancy

Safety belts work for everyone, including pregnant
women. Like all occupants, they are more likely to be
seriously injured if they don’t wear safety belts.

A pregnant woman should wear a lap-shoulder belt, and
the lap portion should be worn as low as possible, below
the rounding, throughout the pregnancy.

1-19

yellowblue

The best way to protect the fetus is to protect the
mother. When a safety belt is worn properly, it’s more
likely that the fetus won’t be hurt in a crash. For
pregnant women, as for anyone, the key to making
safety belts effective is wearing them properly.

Right Front Passenger Position

The right front passenger’s safety belt works the same
way as the driver’s safety belt. See “Driver Position”
earlier in this section.

Supplemental Restraint System (SRS)

This part explains the Supplemental Restraint System
(SRS) or air bag system.

Your vehicle has “Next Generation” frontal air

-- one air bag for the driver and another air bag

bags
for the right front passenger.

Next Generation frontal air bags are designed to help
reduce the risk of injury from the force of an inflating
air bag. But even these air bags must inflate very
quickly if they are to do their job and comply with
federal regulations.

Here are the most important things to know about the air
bag system:

CAUTION:

You can be severely injured or killed in a crash if
you aren’t wearing your safety belt
have air bags. Wearing your safety belt during a
crash helps reduce your chance of hitting things
inside the vehicle or being ejected from it. Air
bags are “supplemental restraints” to the safety
belts. All air bags
bags

-- are designed to work with safety belts,

but don’t replace them. Air bags are designed to
work only in moderate to severe crashes where
the front of your vehicle hits something. They
aren’t designed to inflate at all in rollover, rear,
side or low

-speed frontal crashes.

-- even Next Generation air

CAUTION: (Continued)

-- even if you

1-20

yellowblue

CAUTION: (Continued)

And, for unrestrained occupants, Next Generation
air bags may provide less protection in frontal
crashes than more forceful air bags have provided
in the past. Everyone in your vehicle should wear a
safety belt properly
bag for that person.

-- whether or not there’s an air

CAUTION:

Air bags inflate with great force, faster than the
blink of an eye. If you’re too close to an inflating
air bag, as you would be if you were leaning
forward, it could seriously injure you. This is true
even with Next Generation frontal air bags.
Safety belts help keep you in position before and
during a crash. Always wear your safety belt,
even with Next Generation air bags. The driver
should sit as far back as possible while still
maintaining control of the vehicle.

CAUTION:

Children who are up against, or very close to, any
air bag when it inflates can be seriously injured or
killed. This is true even though your vehicle has
Next Generation frontal air bags. Air bags plus
lap

-shoulder belts offer the best protection for

adults, but not for young children and infants.
Neither the vehicle’s safety belt system nor its air
bag system is designed for them. Young children
and infants need the protection that a child
restraint system can provide. Always secure
children properly in your vehicle. To read how, see
the part of this manual called “Children” and see
the caution labels on the sunvisors and the right
front passenger’s safety belt.

1-21

yellowblue

There is an air bag readiness
light on the instrument
panel, which shows the air
bag symbol.

The system checks the air bag electrical system for
malfunctions. The light tells you if there is an electrical
problem. See “Air Bag Readiness Light” in the Index
for more information.

How the Air Bag System Works

Where are the air bags?

The driver’s air bag is in the middle of the
steering wheel.

1-22

The right front passenger’s air bag is in the instrument
panel on the passenger’s side.

yellowblue

CAUTION:

If something is between an occupant and an air
bag, the bag might not inflate properly or it
might force the object into that person. The path
of an inflating air bag must be kept clear. Don’t
put anything between an occupant and an air
bag, and don’t attach or put anything on the
steering wheel hub or on or near any other air
bag covering.

1-23

yellowblue

When should an air bag inflate?

An air bag is designed to inflate in a moderate to severe
frontal or near
only if the impact speed is above the system’s designed
“threshold level.” If your vehicle goes straight into a
wall that doesn’t move or deform, the threshold level is
about 9 to 14 mph (14 to 23 km/h). The threshold level
can vary, however, with specific vehicle design, so that
it can be somewhat above or below this range. If your
vehicle strikes something that will move or deform, such
as a parked car, the threshold level will be higher. The
air bag is not designed to inflate in rollovers, side
impacts or rear impacts, because inflation would not
help the occupant.

In any particular crash, no one can say whether an air
bag should have inflated simply because of the damage
to a vehicle or because of what the repair costs were.
Inflation is determined by the angle of the impact and
how quickly the vehicle slows down in frontal or
near

-frontal impacts.

-frontal crash. The air bag will inflate

What makes an air bag inflate?

In an impact of sufficient severity, the air bag sensing
system detects that the vehicle is in a crash. The sensing
system triggers a release of gas from the inflator, which
inflates the air bag. The inflator, air bag and related
hardware are all part of the air bag modules inside the
steering wheel and in the instrument panel in front of the
right front passenger.

How does an air bag restrain?

In moderate to severe frontal or near
even belted occupants can contact the steering wheel or the
instrument panel. Air bags supplement the protection
provided by safety belts. Air bags distribute the force of
the impact more evenly over the occupant’s upper body,
stopping the occupant more gradually. But air bags would
not help you in many types of collisions, including
rollovers, rear impacts and side impacts, primarily because
an occupant’s motion is not toward those air bags. Air
bags should never be regarded as anything more than a
supplement to safety belts, and then only in moderate to
severe frontal or near

-frontal collisions.

-frontal collisions,

1-24

yellowblue

What will you see after an air bag inflates?

After an air bag inflates, it quickly deflates, so quickly
that some people may not even realize the air bag
inflated. Some components of the air bag module
steering wheel hub for the driver’s air bag, or the
instrument panel for the right front passenger’s
bag

-- will be hot for a short time. The parts of the

bag that come into contact with you may be warm,
but not too hot to touch. There will be some smoke and
dust coming from vents in the deflated air bags. Air bag
inflation doesn’t prevent the driver from seeing or from
being able to steer the vehicle, nor does it stop people
from leaving the vehicle.

-- the

CAUTION:

When an air bag inflates, there is dust in the air.
This dust could cause breathing problems for
people with a history of asthma or other
breathing trouble. To avoid this, everyone in the
vehicle should get out as soon as it is safe to do so.
If you have breathing problems but can’t get out
of the vehicle after an air bag inflates, then get
fresh air by opening a window or door.

In many crashes severe enough to inflate an air bag,
windshields are broken by vehicle deformation.
Additional windshield breakage may also occur from the
right front passenger air bag.

D

Air bags are designed to inflate only once. After they
inflate, you’ll need some new parts for your air bag
system. If you don’t get them, the air bag system
won’t be there to help protect you in another crash.
A new system will include air bag modules and
possibly other parts. The service manual for your
vehicle covers the need to replace other parts.

D

Your vehicle is equipped with a crash sensing and
diagnostic module, which records information about
the air bag system. The module records information
about the readiness of the system, when the
system commands air bag inflation and driver’s
safety belt usage at deployment.

D

Let only qualified technicians work on your air bag
system. Improper service can mean that your air
bag system won’t work properly. See your dealer
for service.

1-25

NOTICE:

If you damage the covering for the driver’s or the
right front passenger’s air bag, the bag may not
work properly. You may have to replace the air
bag module in the steering wheel or both the air
bag module and the instrument panel for the
right front passenger’s air bag. Do not open or
break the air bag coverings.

yellowblue

Servicing Your Air Bag-Equipped Vehicle

Air bags affect how your vehicle should be serviced.
There are parts of the air bag system in several places
around your vehicle. You don’t want the system to
inflate while someone is working on your vehicle. Your
dealer and the service manual have information about
servicing your vehicle and the air bag system. T o
purchase a service manual, see “Service and Owner
Publications” in the Index.

If your vehicle ever gets into a lot of water -- such as
water up to the carpeting or higher
your vehicle and soaks the carpet, the air bag controller
can be soaked and ruined. If this ever happens, and then
you start your vehicle, the damage could make the air bags
inflate, even if there’s no crash. You would have to replace
the air bags as well as the sensors and related parts. If your
vehicle is ever in a flood, or if it’s exposed to water that
soaks the carpet, you can avoid needless repair costs by
turning off the vehicle immediately and disconnecting the
battery cables. Don’t let anyone start the vehicle under any
circumstances. See your dealer for service.

-- or if water enters

1-26

CAUTION:

For up to 10 minutes after the ignition key is
turned off and the battery is disconnected, an air
bag can still inflate during improper service. You
can be injured if you are close to an air bag when
it inflates. Avoid yellow connectors. They are
probably part of the air bag system. Be sure to
follow proper service procedures, and make sure
the person performing work for you is qualified
to do so.

The air bag system does not need regular maintenance.

Rear Seat Passengers

It’s very important for rear seat passengers to buckle up!
Accident statistics show that unbelted people in the rear
seat are hurt more often in crashes than those who are
wearing safety belts.

Rear passengers who aren’t safety belted can be thrown
out of the vehicle in a crash. And they can strike others
in the vehicle who are wearing safety belts.

Rear Seat Outside Passenger Positions

Lap-Shoulder Belt

The positions next to the windows have lap
belts. Here’s how to wear one properly.

-shoulder

yellowblue

1. Pick up the latch plate and pull the belt across you.
Don’t let it get twisted.

The shoulder belt may lock if you pull the belt across
you very quickly. If this happens, let the belt go back
slightly to unlock it. Then pull the belt across you
more slowly.

2. Push the latch plate into the buckle until it clicks.

1-27

yellowblue

If the belt stops before it reaches the buckle, tilt the
latch plate and keep pulling until you can buckle it.

Pull up on the latch plate to make sure it is secure.
If the belt is not long enough, see “Safety Belt

Extender” at the end of this section. Make sure the
release button on the buckle is positioned so you
would be able to unbuckle the safety belt quickly if
you ever had to.

1-28

3. T o make the lap part tight, pull down on the buckle
end of the belt as you pull up on the shoulder part.

The lap part of the belt should be worn low and snug on
the hips, just touching the thighs. In a crash, this applies
force to the strong pelvic bones. And you’d be less likely
to slide under the lap belt. If you slid under it, the belt

yellowblue

would apply force at your abdomen. This could cause
serious or even fatal injuries. The shoulder belt should go
over the shoulder and across the chest. These parts of the
body are best able to take belt restraining forces.

The safety belt locks if there’s a sudden stop or a crash,
or if you pull the belt very quickly out of the retractor.

CAUTION:

You can be seriously hurt if your shoulder belt is
too loose. In a crash, you would move forward
too much, which could increase injury. The
shoulder belt should fit against your body.

1-29

T o unlatch the belt, just push the button on the buckle.

Rear Safety Belt Comfort Guides for
Children and Small Adults

Rear shoulder belt comfort guides will provide added
safety belt comfort for children who have outgrown
child restraints and for small adults. When installed on a
shoulder belt, the comfort guide pulls the belt away
from the neck and head.

yellowblue

There is one guide for each outside passenger position in
the rear seat. T o provide added safety belt comfort for
children who have outgrown child restraints and for
smaller adults, the comfort guides may be installed on
the shoulder belts. Here’s how to install a comfort guide
and use the safety belt:

1. Pull the elastic cord out from between the edge of
the seatback and the interior body to remove the
guide from its storage clip.

1-30

yellowblue

2. Slide the guide under and past the belt. The elastic
cord must be under the belt. Then, place the guide
over the belt, and insert the two edges of the belt into
the slots of the guide.

3. Be sure that the belt is not twisted and it lies flat.
The elastic cord must be under the belt and the guide
on top.

1-31

4. Buckle, position and release the safety belt as
described in “Rear Seat Outside Passenger Positions”
earlier in this section. Make sure that the shoulder
belt crosses the shoulder.

yellowblue

T o remove and store the comfort guides, squeeze the
belt edges together so that you can take them out from
the guides. Pull the guide upward to expose its storage
clip, and then slide the guide onto the clip. Rotate the
guide and clip inward and in between the seatback and
the interior body, leaving only the loop of elastic
cord exposed.

Center Passenger Position

1-32

Lap Belt

When you sit in the center seating position, you have a
lap safety belt, which has no retractor. To make the belt
longer, tilt the latch plate and pull it along the belt.

yellowblue

T o make the belt shorter, pull its free end as shown until
the belt is snug.

Buckle, position and release it the same way as the lap
part of a lap
see “Safety Belt Extender” at the end of this section.

Make sure the release button on the buckle is positioned
so you would be able to unbuckle the safety belt quickly
if you ever had to.

-shoulder belt. If the belt isn’t long enough,

1-33

yellowblue

Children

Everyone in a vehicle needs protection! That includes
infants and all children smaller than adult size. Neither
the distance traveled nor the age and size of the traveler
changes the need, for everyone, to use safety restraints.
In fact, the law in every state in the United States and in
every Canadian province says children up to some age
must be restrained while in a vehicle.

Smaller Children and Babies

CAUTION:

Children who are up against, or very close to, any
air bag when it inflates can be seriously injured
or killed. This is true even though your vehicle
has Next Generation frontal air bags. Air bags
plus lap
for adults, but not for young children and
infants. Neither the vehicle’s safety belt system
nor its air bag system is designed for them.
Young children and infants need the protection
that a child restraint system can provide. Always
secure children properly in your vehicle.

-shoulder belts offer the best protection

1-34

CAUTION:

Smaller children and babies should always be
restrained in a child or infant restraint. The
instructions for the restraint will say whether it is
the right type and size for your child. A very
young child’s hip bones are so small that a
regular belt might not stay low on the hips, as it
should. Instead, the belt will likely be over the
child’s abdomen. In a crash, the belt would apply
force right on the child’s abdomen, which could
cause serious or fatal injuries. So, be sure that
any child small enough for one is always properly
restrained in a child or infant restraint.

yellowblue

Infants need complete support, including support for the
head and neck. This is necessary because an infant’s neck
is weak and its head weighs so much compared with the
rest of its body. In a frontal crash, an infant in a rear
restraint settles into the restraint, so the crash forces can be
distributed across the strongest part of the infant’s body,
the back and shoulders. A baby should be secured in an
appropriate infant restraint. This is so important that many
hospitals today won’t release a newborn infant to its
parents unless there is an infant restraint available for the
baby’s first trip in a motor vehicle.

-facing

1-35

CAUTION:

Never hold a baby in your arms while riding in a
vehicle. A baby doesn’t weigh much
crash. During a crash a baby will become so
heavy you can’t hold it. For example, in a crash

CAUTION: (Continued)

-- until a

CAUTION: (Continued)

at only 25 mph (40 km/h), a 12-lb. (5.5 kg) baby
will suddenly become a 240
your arms. The baby would be almost impossible
to hold.

Secure the baby in an infant restraint.

-lb. (110 kg) force on

yellowblue

1-36

Child Restraints

Every time infants and young children ride in
vehicles, they should have protection provided by
appropriate restraints.

Q: What are the different types of add-on

child restraints?

A: Add-on child restraints are available in four basic

types. When selecting a child restraint, take into
consideration not only the child’s weight and size,
but also whether or not the restraint will be
compatible with the motor vehicle in which it will
be used.

yellowblue

An infant car bed (A) is a special bed made for use
in a motor vehicle. It’s an infant restraint system
designed to restrain or position a child on a
continuous flat surface. With an infant car bed,
make sure that the infant’s head rests toward the
center of the vehicle.

1-37

A rear-facing infant restraint (B) positions an infant
to face the rear of the vehicle. Rear
restraints are designed for infants of up to about
20 lbs. (9 kg) and about one year of age. This type
of restraint faces the rear so that the infant’s head,
neck and body can have the support they need in a
frontal crash. Some infant seats come in two
parts

-- the base stays secured in the vehicle and

the seat part is removable.

-facing infant

yellowblue

1-38

yellowblue

A forward-facing child restraint (C-E) positions a
child upright to face forward in the vehicle. These
forward
protect children who are from 20 to 40 lbs. (9 to
18 kg) and about 26 to 40 inches (66 to 102 cm) in
height, or up to around four years of age. One type,
a convertible restraint, is designed to be used either
as a rear
child seat.

-facing restraints are designed to help

-facing infant seat or a forward-facing

1-39

A booster seat (F, G) is designed for children who
are about 40 to 60 lbs., or even up to 80 lbs. (18 to
27 kg, or even up to 36 kg), and about four to eight
years of age. A booster seat is designed to improve
the fit of the vehicle’s safety belt system. Booster
seats with shields use lap
booster seats without shields use lap
Booster seats can also help a child to see out
the window.

-only belts; however,

-shoulder belts.

yellowblue

1-40

When choosing a child restraint, be sure the child
restraint is designed to be used in a vehicle. If it is, it
will have a label saying that it meets federal motor
vehicle safety standards.

Then follow the instructions for the restraint. You may
find these instructions on the restraint itself or in a
booklet, or both. These restraints use the belt system in
your vehicle, but the child also has to be secured within
the restraint to help reduce the chance of personal injury.
The instructions that come with the infant or child
restraint will show you how to do that. Both the owner’s
manual and the child restraint instructions are important,
so if either one of these is not available, obtain a
replacement copy from the manufacturer.

Where to Put the Restraint

Accident statistics show that children are safer if they
are restrained in the rear rather than the front seat. We at
General Motors therefore recommend that you put your
child restraint in the rear seat. Never put a rear
child restraint in the front passenger seat. Here’s why:

-facing

yellowblue

CAUTION:

A child in a rear-facing child restraint can be
seriously injured or killed if the right front
passenger’s air bag inflates, even though your
vehicle has Next Generation frontal air bags. This
is because the back of the rear
restraint would be very close to the inflating air
bag. Always secure a rear
in a rear seat.

You may secure a forward-facing child restraint
in the right front seat, but before you do, always
move the front passenger seat as far back as it
will go. It’s better to secure the child restraint in
a rear seat.

Wherever you install it, be sure to secure the child
restraint properly.

Keep in mind that an unsecured child restraint can move
around in a collision or sudden stop and injure people in
the vehicle. Be sure to properly secure any child
restraint in your vehicle

-- even when no child is in it.

-facing child

-facing child restraint

1-41

yellowblue

Top Strap

Canadian law requires that forward-facing
child restraints have a top strap, and that the strap
be anchored.

If your child restraint has a top strap, it should be
anchored. If you need to have an anchor installed, your
dealer can obtain a kit with anchor hardware and
installation instructions specifically designed for this
vehicle. The dealer can then install the anchor for you.

This work will be done for you free of charge. Or, you
may install the anchor yourself using the instructions
provided in the kit.

Securing a Child Restraint in a Rear
Outside Seat Position

You’ll be using the lap-shoulder belt. See the earlier part
about the top strap if the child restraint has one. Be sure
to follow the instructions that came with the child
restraint. Secure the child in the child restraint when and
as the instructions say.

1. Put the restraint on the seat.

2. Pick up the latch plate, and run the lap and shoulder
portions of the vehicle’s safety belt through or
around the restraint. The child restraint instructions
will show you how.

1-42

yellowblue

Tilt the latch plate to adjust the belt if needed.
If the shoulder belt goes in front of the child’s face or

neck, put it behind the child restraint.

3. Buckle the belt. Make sure the release button is
positioned so you would be able to unbuckle the
safety belt quickly if you ever had to.

1-43

4. T o tighten the belt, pull up on the shoulder belt while
you push down on the child restraint. If you’re using
a forward
helpful to use your knee to push down on the child
restraint as you tighten the belt.

5. Push and pull the child restraint in different
directions to be sure it is secure.

-facing child restraint, you may find it

yellowblue

T o remove the child restraint, just unbuckle the vehicle’s
safety belt and let it go back all the way. The safety belt
will move freely again and be ready to work for an adult
or larger child passenger.

Securing a Child Restraint in the Center
Rear Seat Position

You’ll be using the lap belt. Be sure to follow the
instructions that came with the child restraint. Secure
the child in the child restraint when and as the
instructions say.

See the earlier part about the top strap if the child
restraint has one.

1-44

yellowblue

1. Make the belt as long as possible by tilting the latch
plate and pulling it along the belt.

2. Put the restraint on the seat.

3. Run the vehicle’s safety belt through or around the
restraint. The child restraint instructions will show
you how.

4. Buckle the belt. Make sure the release button is
positioned so you would be able to unbuckle the
safety belt quickly if you ever had to.

5. T o tighten the belt, pull its free end while you push
down on the child restraint. If you’re using a
forward
helpful to use your knee to push down on the child
restraint as you tighten the belt.

-facing child restraint, you may find it

1-45

6. Push and pull the child restraint in different
directions to be sure it is secure.

T o remove the child restraint, just unbuckle the vehicle’s
safety belt. It will be ready to work for an adult or larger
child passenger.

Securing a Child Restraint in the Right
Front Seat Position

Your vehicle has a right front passenger air bag. Never
put a rear

-facing child restraint in this seat. Here’s why:

CAUTION:

A child in a rear-facing child restraint can be
seriously injured or killed if the right front
passenger’s air bag inflates, even though your
vehicle has Next Generation frontal air bags. This
is because the back of the rear
restraint would be very close to the inflating air
bag. Always secure a rear
in the rear seat.

Although a rear seat is a safer place, you can secure a
forward

-facing child restraint in the right front seat.

-facing child

-facing child restraint

yellowblue

1-46

You’ll be using the lap-shoulder belt. See the earlier part
about the top strap if the child restraint has one. Be sure
to follow the instructions that came with the child
restraint. Secure the child in the child restraint when and
as the instructions say.

1. Because your vehicle has a right front passenger air
bag, always move the seat as far back as it will go
before securing a forward
“Seats” in the Index.)

2. Put the restraint on the seat.

3. Pick up the latch plate, and run the lap and shoulder
portions of the vehicle’s safety belt through or
around the restraint. The child restraint instructions
will show you how.

-facing child restraint. (See

yellowblue

Tilt the latch plate to adjust the belt if needed.
If the shoulder belt goes in front of the child’s face or

neck, put it behind the child restraint.

1-47

yellowblue

4. Buckle the belt. Make sure the release button is
positioned so you would be able to unbuckle the
safety belt quickly if you ever had to.

1-48

5. T o tighten the belt, pull up on the shoulder belt while
you push down on the child restraint. You may find it
helpful to use your knee to push down on the child
restraint as you tighten the belt.

6. Push and pull the child restraint in different
directions to be sure it is secure.

T o remove the child restraint, just unbuckle the vehicle’s
safety belt and let it go back all the way. The safety belt
will move freely again and be ready to work for an adult
or larger child passenger.

yellowblue

Larger Children

Children who have outgrown child restraints should
wear the vehicle’s safety belts.

If you have the choice, a child should sit next to a
window so the child can wear a lap-shoulder belt and
get the additional restraint a shoulder belt can provide.

Accident statistics show that children are safer if they
are restrained in the rear seat. But they need to use the
safety belts properly.

D

Children who aren’t buckled up can be thrown out in
a crash.

D

Children who aren’t buckled up can strike other
people who are.

1-49

yellowblue

CAUTION:

Never do this.
Here two children are wearing the same belt. The

belt can’t properly spread the impact forces. In a
crash, the two children can be crushed together
and seriously injured. A belt must be used by
only one person at a time.

Q: What if a child is wearing a lap-shoulder belt,

but the child is so small that the shoulder belt is
very close to the child’s face or neck?

A: Move the child toward the center of the vehicle, but

be sure that the shoulder belt still is on the child’s
shoulder, so that in a crash the child’s upper body
would have the restraint that belts provide. If the
child is sitting in a rear seat outside position, see
“Rear Safety Belt Comfort Guides” in the Index.
If the child is so small that the shoulder belt is still
very close to the child’s face or neck, you might
want to place the child in the center seat position,
the one that has only a lap belt.

1-50

yellowblue

CAUTION:

Never do this.
Here a child is sitting in a seat that has a

lap

-shoulder belt, but the shoulder part is behind

the child. If the child wears the belt in this way, in
a crash the child might slide under the belt. The
belt’s force would then be applied right on the
child’s abdomen. That could cause serious or
fatal injuries.

Wherever the child sits, the lap portion of the belt
should be worn low and snug on the hips, just touching
the child’s thighs. This applies belt force to the child’s
pelvic bones in a crash.

1-51

yellowblue

Safety Belt Extender

If the vehicle’s safety belt will fasten around you, you
should use it.

But if a safety belt isn’t long enough to fasten, your
dealer will order you an extender. It’s free. When you go
in to order it, take the heaviest coat you will wear, so the
extender will be long enough for you. The extender will
be just for you, and just for the seat in your vehicle that
you choose. Don’t let someone else use it, and use it
only for the seat it is made to fit. T o wear it, just attach it
to the regular safety belt.

Checking Your Restraint Systems

Now and then, make sure the safety belt reminder light
and all your belts, buckles, latch plates, retractors and
anchorages are working properly. Look for any other
loose or damaged safety belt system parts. If you see
anything that might keep a safety belt system from
doing its job, have it repaired.

T orn or frayed safety belts may not protect you in a
crash. They can rip apart under impact forces. If a belt is
torn or frayed, get a new one right away.

Also look for any opened or broken air bag covers, and
have them repaired or replaced. (The air bag system
does not need regular maintenance.)

Replacing Restraint System Parts
After a Crash

If you’ve had a crash, do you need new belts?
After a very minor collision, nothing may be necessary.

But if the belts were stretched, as they would be if worn
during a more severe crash, then you need new belts.

If belts are cut or damaged, replace them. Collision
damage also may mean you will need to have safety belt
or seat parts repaired or replaced. New parts and repairs
may be necessary even if the belt wasn’t being used at
the time of the collision.

If your seat adjuster won’t work after a crash, the special
part of the safety belt that goes through the seat to the
adjuster may need to be replaced.

If an air bag inflates, you’ll need to replace air bag
system parts. See the part on the air bag system earlier in
this section.

1-52

yellowblue

Section 2 Features and Controls

Here you can learn about the many standard and optional features on your vehicle, and information on starting,
shifting and braking. Also explained are the instrument panel and the warning systems that tell you if everything is
working properly

2

-2 Keys

2

-4 Door Locks

-6 Remote Lock Control (Option)

2
2

-10 Trunk

-12 Theft

2
2

-13 Passlock

2-13 New Vehicle “Break-In”

-14 Ignition Positions

2
2

-16 Starting Your Engine

-17 Engine Coolant Heater (If Equipped)

2
2

-19 Automatic Transaxle Operation

2

-23 Parking Brake

-24 Shifting Into PARK (P)

2
2

-26 Shifting Out of PARK (P)

-27 Parking Over Things That Burn

2

-- and what to do if you have a problem.

R

-28 Engine Exhaust

2
2

-28 Running Your Engine While You’re Parked

-29 Windows

2
2

-30 Horn

-30 Tilt Wheel

2
2

-31 Turn Signal/Multifunction Lever

2

-38 Exterior Lamps

-40 Interior Lamps

2
2

-42 Mirrors

-44 Storage Compartments

2
2

-47 Sunroof (If Equipped)

2

-48 The Instrument Panel-Your

Information System

2-50 Instrument Panel Cluster

-52 Warning Lights, Gages and Indicators

2

2-

2-1

Keys

CAUTION:

Leaving children in a vehicle with the ignition
key is dangerous for many reasons. A child or
others could be badly injured or even killed.

They could operate power windows or other
controls or even make the vehicle move. Don’t
leave the keys in a vehicle with children.

yellowblue

2-2

yellowblue

One key is used for the
ignition, the doors and all
other locks.

When a new vehicle is delivered, the key has a

-coded key tag. This tag may be removed by your

bar
dealer before it is delivered.

Each tag has a key code on it that tells your dealer or a
qualified locksmith how to make extra keys. Keep the
tag in a safe place. If you lose your keys, you’ll be able
to have one made easily using this tag.

If you need a new key, go to your dealer for the correct
key code.

In an emergency , call the Oldsmobile Roadside
Assistance Program at 1

-800-442-OLDS (6537).

NOTICE:

Your vehicle has a number of new features that
can help prevent theft, therefore you can have a
lot of trouble getting into your vehicle if you ever
lock your keys inside. You may even have to
damage your vehicle to get in. So be sure you
have extra keys.

2-3

Door Locks

CAUTION:

Unlocked doors can be dangerous.
Passengers -- especially children -- can easily

open the doors and fall out. When a door is
locked, the inside handle won’t open it.

Outsiders can easily enter through an unlocked
door when you slow down or stop your vehicle.

This may not be so obvious: You increase the
chance of being thrown out of the vehicle in a
crash if the doors aren’t locked. Wear safety belts
properly, lock your doors, and you will be far
better off whenever you drive your vehicle.

There are several ways to lock and unlock your vehicle.
From the outside, use your key or remote lock control

transmitter, if your vehicle is equipped with it.

yellowblue

From the inside, to lock the door, move the locking
lever forward.

T o unlock the door, move the locking lever rearward.

2-4

yellowblue

Power Door Locks

With the power door locks,
you can unlock or lock all
of the doors of your vehicle
from the driver or front
passenger door lock switch.

Pull up on the switch to unlock all the doors. Push down
on the switch to lock the doors.

Door Ajar Reminder

If one of the doors of your vehicle is not closed
properly, the ignition is on and you shift from PARK (P)
or NEUTRAL (N), you will hear a chime. Also, a door
ajar light on the instrument panel will come on and stay
on until the doors are closed and completely latched.

Rear Door Security Locks

Your vehicle is equipped
with rear door security
locks that help prevent
passengers from opening
the rear doors of your
vehicle from the inside.

The switch is located on the inside of the rear door. To
use one of these locks:

1. Move the switch up.

2. Close the door.

3. Do the same thing on the other rear door.

2-5

yellowblue

The rear doors of your vehicle cannot be opened from
the inside when this feature is in use. If you want to
open a rear door when the security lock is on:

1. Unlock the door from the inside.

2. Then open the door from the outside.
If you don’t cancel the security lock feature, adults or

older children who ride in the rear won’t be able to open
the rear door from the inside. You should let adults and
older children know how these security locks work, and
how to cancel the locks.

T o cancel the rear door lock:

1. Unlock the door from the inside and open it from
the outside.

2. Move the switch down.

3. Do the same for the other rear door.

The rear doors will now work normally.

Leaving Your Vehicle

If you are leaving your vehicle, open your door and lock
the doors from the inside, then get out and close
the door.

Remote Lock Control (Option)

If your vehicle has this option, you can lock and unlock
your doors or unlock your trunk from about 3 feet (1 m)
up to 30 feet (9 m) away using the remote lock control
transmitter supplied with your vehicle.

In addition, the system
illuminates the interior
lights for a set period of
time. The remote lock
control system consists of a
receiver, which is located in
the vehicle, and two
hand

-held transmitters.

Your remote lock control operates on a radio frequency
subject to Federal Communications Commission (FCC)
Rules and with Industry Canada.

2-6

yellowblue

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause
undesired operation.

This device complies with RSS
Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation of
the device.

Changes or modifications to this system by other than an
authorized service facility could void authorization to
use this equipment.

-210 of Industry Canada.

At times you may notice a decrease in range. This is
normal for any remote keyless entry system. If the
transmitter does not work or if you have to stand closer
to your vehicle for the transmitter to work, try this:

D

Check to determine if battery replacement or
resynchronization is necessary. See the instructions
that follow.

D

Check the distance. You may be too far from your
vehicle. You may need to stand closer during rainy
or snowy weather.

D

Check the location. Other vehicles or objects may be
blocking the signal. T ake a few steps to the left or
right, hold the transmitter higher, and try again.

D

If you’re still having trouble, see your dealer or a
qualified technician for service.

2-7

yellowblue

Operation

The following functions are available with the remote
lock control system:

LOCK All doors will automatically lock when the
LOCK button on the transmitter is pressed. Press the
button a second time and you will hear a “chirp” to
indicate that the doors have been locked.

UNLOCK:The driver’s door will unlock automatically
when the UNLOCK button on the transmitter is pressed.
If the UNLOCK button is pressed again within five
seconds, all remaining doors will unlock.

: The trunk will unlock anytime the vehicle
symbol on the transmitter is pressed, the trunk lockout is
not engaged and the gear selector is in PARK (P) or
NEUTRAL (N).

Matching Transmitter(s) To Your Vehicle

Each remote lock control transmitter is coded to prevent
another transmitter from unlocking your vehicle. If a
transmitter is lost or stolen, a replacement can be
purchased through your dealer. Remember to bring any
remaining transmitters with you when you go to your
dealer. When the dealer matches the replacement
transmitter to your vehicle, any remaining transmitters
must also be matched. Once your dealer has coded the
new transmitter, the lost transmitter will not unlock your
vehicle. Each vehicle can have only four transmitters
matched to it.

You can match your transmitter to as many 1999
General Motors vehicles as you own, as long as they
have the same remote lock control system. Contact your
dealer for assistance with this.

2-8

Battery Replacement

Under normal use, the battery in your remote lock
control transmitter should last about two years.

You can tell the battery is weak if the transmitter won’t
work at the normal range in any location. If you have to
get close to your vehicle before the transmitter works,
it’s probably time to change the battery.

NOTICE:

When replacing the battery, use care not to touch
any of the circuitry. Static from your body
transferred to these surfaces may damage
the transmitter.

yellowblue

T o replace the battery in the remote lock
control transmitter:

1. Use a small coin or flathead screwdriver to separate
the bottom half from the top half of the transmitter.

2. Remove the battery and replace it with the new one.
Make sure the positive (+) side of the battery faces
down. Use one three
type battery.

3. Put the two halves back together. Make sure the
cover is on tightly, so water won’t get in.

-volt, CR2032, or equivalent,

2-9

yellowblue

4. Check the operation of the transmitter with your
vehicle. If the transmitter does not work, try
resynchronizing the transmitter with the receiver.

Resynchronization

Your remote lock control system is equipped with a
security system that prevents anyone from recording and
playing back your signal. The transmitter does not send
the same signal twice to the receiver. The receiver will
not respond to a signal that has been sent to it more
than once.

T o resynchronize your transmitter and receiver, follow
these directions:

1. Stand close to your vehicle.

2. Press and hold the LOCK and UNLOCK buttons on
the transmitter at the same time.

3. Hold the buttons for five seconds. In this time, the
doors should lock and unlock once. This confirms
the resynchronization. If the doors do not lock and
unlock, see your dealer for service.

Trunk

To unlock the trunk from the outside, insert the key and turn
the trunk lock cylinder or use the remote lock lock control.

CAUTION:

It can be dangerous to drive with the trunk lid
open because carbon monoxide (CO) gas can
come into your vehicle. You can’t see or smell
CO. It can cause unconsciousness and even death.

If you must drive with the trunk lid open or if
electrical wiring or other cable connections must
pass through the seal between the body and the
trunk lid:

D

Make sure all other windows are shut.

D

Turn the fan on your heating or cooling
system to its highest speed with the setting on
VENT. That will force outside air into your
vehicle. See “Comfort Controls” in the Index.

D

If you have air outlets on or under the
instrument panel, open them all the way.

See “Engine Exhaust” in the Index.

2-10

Remote Trunk Release

Press the remote release button, located on the lower left
side of the instrument panel, to release the trunk lid.
Make sure the lockout feature is not activated. Also, the
remote trunk release will only work when the gearshift
lever is in PARK (P) or NEUTRAL (N).

Remote Trunk Release Lockout

Your remote trunk release is equipped with a lockout
feature to help prevent unauthorized entry into the trunk
when leaving the vehicle unattended. The switch is
located on the inside of the trunk lid, mounted to the
trunk lid latch.

yellowblue

T o turn the lockout on, slide the switch all the way to the
left. T o turn the lockout off, slide the switch all the way
to the right.

When the lockout is on, the remote trunk release switch
on the instrument panel will not release the trunk lid.
However, the trunk lid can still be opened with the key,
but not with the remote lock control transmitter.

2-11

yellowblue

Theft

Vehicle theft is big business, especially in some cities.
Although your vehicle has a number of theft
features, we know that nothing we put on it can make it
impossible to steal. However, there are ways you
can help.

Key in the Ignition

If you leave your vehicle with the keys inside, it’s an
easy target for joy riders or professional thieves
don’t do it.

When you park your vehicle and open the driver’s door,
you’ll hear a chime reminding you to remove your key
from the ignition and take it with you. Always do this.
Your ignition and transaxle will be locked. And
remember to lock the doors.

-deterrent

-- so

Parking at Night

Park in a lighted spot, close all windows and lock your
vehicle. Remember to keep your valuables out of sight.
Put them in a storage area, or take them with you.

Parking Lots

If you park in a lot where someone will be watching
your vehicle, it’s best to lock it up and take your keys.
But what if you have to leave your key?

D

If possible, park in a busy, well lit area.

D

Put your valuables in a storage area, like your
trunk or glove box. Be sure to close and lock the
storage area.

D

Close all windows.

D

Move the trunk release lockout switch to the
ON position.

D

Lock the glove box.

D

Lock all the doors except the driver’s.

D

If your vehicle has a remote lock control system,
take the transmitter with you.

2-12

yellowblue

Passlock

Your vehicle is equipped with the Passlock
theft

-deterrent system.

Passlock is a passive theft-deterrent system. Passlock
enables fuel if the ignition lock cylinder is turned with a
valid key . If a correct key is not used or the ignition lock
cylinder is tampered with, fuel is disabled.

During normal operation, the THEFT SYSTEM light
will go off approximately five seconds after the key is
turned to the ON ignition position.

If the THEFT SYSTEM light flashes, wait until the light
stops flashing before starting the engine.

In an emergency , call the Oldsmobile Roadside
Assistance Center at 1

R

-800-442-OLDS (6537).

New Vehicle “Break-In”

NOTICE:

Your vehicle doesn’t need an elaborate
“break

-in.” But it will perform better in the long

run if you follow these guidelines:

D

Don’t drive at any one speed -- fast or
slow

-- for the first 500 miles (805 km).

Don’t make full

D

Avoid making hard stops for the first
200 miles (322 km) or so. During this time
your new brake linings aren’t yet broken
in. Hard stops with new linings can mean
premature wear and earlier replacement.
Follow this breaking
time you get new brake linings.

D

Don’t tow a trailer during break
See “Towing a Trailer” in the Index for
more information.

-throttle starts.

-in guideline every

-in.

2-13

Ignition Positions

CAUTION:

Leaving children in a vehicle with the ignition
key is dangerous for many reasons. A child or
others could be injured or even killed. They could
operate power windows or other controls or even
make the vehicle move. Don’t leave the keys in
the vehicle with children.

yellowblue

With the ignition key in the ignition switch, you can turn
the switch to four positions.

OFF (A): Before you put the key into the ignition
switch, the switch is off. It is the only position from
which you can remove the key. This position locks your
ignition and transaxle. A warning chime will sound if
you open the driver’s door when the ignition is off and
the key is in the ignition.

2-14

yellowblue

ACC (Accessory) (B): This position unlocks the
transaxle. It also lets you use things like the radio and
windshield wipers when the engine is not running. T o
use ACC, push in the key and turn it clockwise. Use this
position if your vehicle must be pushed or towed, but
never try to push

ON (C): This position unlocks the ignition and
transaxle. This position is also where the key returns
after you start your engine and release the switch. The
switch stays in ON when the engine is running. But even
when the engine is not running, you can use ON to
operate your electrical power accessories, and to display
some instrument panel warning lights.

-start your vehicle.

START (D): This position starts the engine. When the
engine starts, release the key. The ignition switch will
return to ON for normal driving.

NOTICE:

If your key seems stuck in OFF and you can’t
turn it, be sure you are using the correct key; if
so, is it all the way in? Turn the key only with
your hand. Using a tool to force it could break
the key or the ignition switch. If none of this
works, then your vehicle needs service.

2-15

yellowblue

Starting Your Engine

Move your shift lever to PARK (P) or NEUTRAL (N).
Your engine won’t start in any other position
safety feature. T o restart when you’re already moving,
use NEUTRAL (N) only.

-- that’s a

NOTICE:

Don’t try to shift to PARK (P) if your vehicle is
moving. If you do, you could damage the
transaxle. Shift to PARK (P) only when your
vehicle is stopped.

Starting Your Engine

1. Without pushing the accelerator pedal, turn your
ignition key to START. When the engine starts, let
go of the key. The idle speed will go down as your
engine gets warm.

NOTICE:

Holding your key in START for longer than
15 seconds at a time will cause your battery to be
drained much sooner. And the excessive heat can
damage your starter motor. Wait about
15 seconds between each try to help avoid
draining your battery or damaging your starter.

2-16

yellowblue

2. If your engine won’t start (or starts but then stops), it
could be flooded with too much gasoline. Try
pushing your accelerator pedal all the way to the
floor and holding it there as you hold the key in
START for up to 15 seconds. This clears the extra
gasoline from the engine.

NOTICE:

Your engine is designed to work with the
electronics in your vehicle. If you add electrical
parts or accessories, you could change the way
the engine operates. Before adding electrical
equipment, check with your dealer. If you don’t,
your engine might not perform properly.

If you ever have to have your vehicle towed, see
the part of this manual that tells how to do it
without damaging your vehicle. See “Towing
Your Vehicle” in the Index.

Engine Coolant Heater (If Equipped)

In very cold weather, 0_F (-18_C) or colder, the engine
coolant heater can help. You’ll get easier starting and
better fuel economy during engine warm
the coolant heater should be plugged in a minimum of
four hours prior to starting your vehicle.

-up. Usually,

2-17

yellowblue

To Use the Engine Coolant Heater

1. Turn off the engine.

2. Open the hood and unwrap the electrical cord. The
engine coolant heater cord is located near the air
cleaner/filter.

3. Plug it into a normal, grounded 110

-volt AC outlet.

CAUTION:

Plugging the cord into an ungrounded outlet
could cause an electrical shock. Also, the wrong
kind of extension cord could overheat and cause
a fire. You could be seriously injured. Plug the
cord into a properly grounded three
110

-volt AC outlet. If the cord won’t reach, use a

heavy

-duty three-prong extension cord rated for

at least 15 amps.

-prong

4. Before starting the engine, be sure to unplug and
store the cord as it was before to keep it away from
moving engine parts. If you don’t, it could
be damaged.

How long should you keep the coolant heater plugged
in? The answer depends on the outside temperature, the
kind of oil you have, and some other things. Instead of
trying to list everything here, we ask that you contact
your dealer in the area where you’ll be parking your
vehicle. The dealer can give you the best advice for that
particular area.

2-18

Automatic Transaxle Operation

Your automatic transaxle has a shift lever located on the
console between the seats.

PARK (P): This locks your front wheels. It’s the best
position to use when you start your engine because your
vehicle can’t move easily.

yellowblue

CAUTION:

It is dangerous to get out of your vehicle if the
shift lever is not fully in PARK (P) with the
parking brake firmly set. Your vehicle can roll.

Don’t leave your vehicle when the engine is
running unless you have to. If you have left the
engine running, the vehicle can move suddenly.
You or others could be injured. To be sure your
vehicle won’t move, even when you’re on fairly
level ground, always set your parking brake and
move the shift lever to PARK (P).

See “Shifting Into PARK (P)” in the Index. If
you’re pulling a trailer, see “Towing a Trailer” in
the Index.

2-19

yellowblue

Ensure the shift lever is fully in PARK (P) before
starting the engine. Your vehicle has a Brake
Shift Interlock (BTSI). You have to apply your regular
brake before you can shift from PARK (P) when the
ignition key is in the RUN. If you cannot shift out of
PARK (P), ease pressure on the shift lever -- push the
shift lever all the way into PARK (P)
brake application. Then move the shift lever into the
gear you wish. (Press the shift lever button before
moving the shift lever.) See “Shifting Out of PARK (P)”
later in this section.

REVERSE (R): Use this gear to back up.

-Transaxle

-- as you maintain

NOTICE:

Shifting to REVERSE (R) while your vehicle is
moving forward could damage your transaxle.
Shift to REVERSE (R) only after your vehicle
is stopped.

T o rock your vehicle back and forth to get out of snow,
ice or sand without damaging your transaxle, see “Stuck
In Sand, Mud, Ice or Snow” in the Index.

NEUTRAL (N): In this position, your engine doesn’t
connect with the wheels. To restart when you’re already
moving, use NEUTRAL (N) only . Also, use NEUTRAL (N)
when your vehicle is being towed.

CAUTION:

Shifting out of PARK (P) or NEUTRAL (N) while
your engine is “racing” (running at high speed) is
dangerous. Unless your foot is firmly on the
brake pedal, your vehicle could move very
rapidly. You could lose control and hit people or
objects. Don’t shift out of PARK (P) or
NEUTRAL (N) while your engine is racing.

NOTICE:

Do not shift out of PARK (P) or NEUTRAL (N)
with the engine racing. Your transaxle can be
damaged by doing this and will not be covered by
your warranty. Shift your transaxle according to
the instructions in this manual.

2-20

yellowblue

AUTOMATIC OVERDRIVE (D): This position is
for normal driving. If you need more power for passing,
and you’re:

D

Going less than 35 mph (56 km/h), push your
accelerator pedal about halfway down.

D

Going about 35 mph (56 km/h) or more, push the
accelerator all the way down. You’ll shift down to
the next gear and have more power.

NOTICE:

If your vehicle seems to start up rather slowly, or
if it seems not to shift gears as you go faster,
something may be wrong with a transaxle system
sensor. If you drive very far that way, your
vehicle can be damaged. So, if this happens, have
your vehicle serviced right away. Until then, you
can use SECOND (2) when you are driving less
than 35 mph (56 km/h) and AUTOMATIC
OVERDRIVE (D) for higher speeds.

THIRD (3): This position is also used for normal

driving, however, it offers more power and lower fuel
economy than AUTOMATIC OVERDRIVE (D). Here
are some times you might choose THIRD (3) instead of
AUTOMATIC OVERDRIVE (D):

D

When driving on hilly, winding roads.

D

When towing a trailer, so there is less shifting
between gears.

D

When going down a steep hill.

SECOND (2): This position gives you more power but
lower fuel economy. You can use SECOND (2) on hills.
It can help control your speed as you go down steep
mountain roads, but then you would also want to use
your brakes off and on.

2-21

NOTICE:

Don’t drive in SECOND (2) for more than
25 miles (41 km), or at speeds over 55 mph
(88 km/h), or you can damage your transaxle.
Use AUTOMATIC OVERDRIVE (D) or
THIRD (3) as much as possible. Don’t shift into
SECOND (2) unless you are going slower than
65 mph (105 km/h) or you can damage
your engine.

SECOND (2) will select either first or second gear
depending on vehicle speed. If your vehicle is slowing,
the transaxle will downshift to first gear at 20 to
25 miles per hour (32 to 40 km/h) for engine braking.
You may notice some variation in shift speed in
SECOND (2) when accelerating or braking.

yellowblue

FIRST (1): This position gives you even more power
(but lower fuel economy) than SECOND (2). You can
use it on very steep hills, or in deep snow or mud. If the
selector lever is put in FIRST (1), the transaxle won’t
shift into first gear until the vehicle is going
slowly enough.

NOTICE:

If your front wheels can’t rotate, don’t try to
drive. This might happen if you were stuck in
very deep sand or mud or were up against a solid
object. You can damage your transaxle.

Also, if you stop when going uphill, don’t hold
your vehicle there with only the accelerator
pedal. This could overheat and damage the
transaxle. Use your brakes or shift into PARK (P)
to hold your vehicle in position on a hill.

2-22

yellowblue

Second-Gear Start

Your vehicle is equipped with a second-gear start
feature. Place the shift lever in SECOND (2) gear to
provide more traction when you are starting on ice or
other slippery surfaces. The transaxle will be in
SECOND (2) gear when the vehicle begins to move.
After starting in SECOND (2) gear, place the shift lever
in THIRD (3) or AUTOMATIC OVERDRIVE (D).

This feature is only for improved traction only when the
road surface is slippery and is not intended for
continuous use or when the vehicle is stuck in sand,
mud, ice, snow or gravel.

Parking Brake

T o set the parking brake,
hold the regular brake pedal
down with your right foot.
Push down the parking
brake pedal with your left
foot. If the ignition is on,
the brake system warning
light will come on.

T o release the parking brake, hold the regular brake
pedal down with your right foot. Push down on the
parking brake pedal with your left foot. If the parking
brake is not released when you begin to drive, a chime
will sound warning you that the parking brake is still on.

2-23

yellowblue

NOTICE:

Driving with the parking brake on can cause
your rear brakes to overheat. You may have to
replace them, and you could also damage other
parts of your vehicle.

If you are towing a trailer and are parking on a hill, see
“T owing a Trailer” in the Index. That section shows
what to do first to keep the trailer from moving.

Shifting Into PARK (P)

CAUTION:

It can be dangerous to get out of your vehicle if
the shift lever is not fully in PARK (P) with the
parking brake firmly set. Your vehicle can roll. If
you have left the engine running, the vehicle can
move suddenly. You or others could be injured.
To be sure your vehicle won’t move, even when
you’re on fairly level ground, use the steps that
follow. If you’re pulling a trailer, see “Towing a
Trailer” in the Index.

1. Hold the brake pedal down with your right foot and
set the parking brake.

2-24

2. Move the shift lever into PARK (P) like this:

D

Hold in the button on the lever.

D

Push the lever all the way toward the front of
your vehicle.

3. Turn the ignition key to OFF.

4. Remove the key and take it with you. If you can
leave your vehicle with the key in your hand, your
vehicle is in PARK (P).

yellowblue

Leaving Your Vehicle With the
Engine Running

CAUTION:

It can be dangerous to leave your vehicle with the
engine running. Your vehicle could move
suddenly if the shift lever is not fully in PARK (P)
with the parking brake firmly set. And, if you
leave the vehicle with the engine running, it could
overheat and even catch fire. You or others could
be injured. Don’t leave your vehicle with the
engine running unless you have to.

If you have to leave your vehicle with the engine
running, be sure your vehicle is in PARK (P) and your
parking brake is firmly set before you leave it. After
you’ve moved the shift lever into PARK (P), hold the
regular brake pedal down. Then, see if you can move the
shift lever away from PARK (P) without first pushing
the button.

If you can, it means that the shift lever wasn’t fully
locked into PARK (P).

2-25

yellowblue

Torque Lock

If you are parking on a hill and you don’t shift your
transaxle into PARK (P) properly, the weight of the
vehicle may put too much force on the parking pawl in
the transaxle. You may find it difficult to pull the shift
lever out of PARK (P). This is called “torque lock.” To
prevent torque lock, set the parking brake and then shift
into PARK (P) properly before you leave the driver’s
seat. T o find out how, see “Shifting Into PARK (P)” in
the Index.

When you are ready to drive, move the shift lever out of
PARK (P) before you release the parking brake.

If torque lock does occur, you may need to have another
vehicle push yours a little uphill to take some of the
pressure from the parking pawl in the transaxle, so you
can pull the shift lever out of PARK (P).

Shifting Out of PARK (P)

CAUTION:

Before shifting out of PARK (P) you must fully
apply your regular brakes. Your vehicle can roll.
If you have left the engine running, the vehicle
can move suddenly. You or others could be
injured. If you’re pulling a trailer, see “Towing a
Trailer” in the Index.

Your vehicle has a Brake-Transaxle Shift Interlock
(BTSI). You have to apply your regular brake before
you can shift from PARK (P) when the ignition is in
RUN . See “Automatic Transaxle” in the Index.

2-26

yellowblue

If you cannot shift out of PARK (P), ease pressure on
the shift lever
PARK (P)
move the shift into the gear you wish. (Press the shift
lever button before moving the shift lever.)

If you ever hold the brake pedal down but still can’t
shift out of PARK (P), try this:

1. Turn the key to the ACC ignition position.

2. Apply and hold the regular brake until the end of
Step 5.

3. Shift to NEUTRAL (N).

4. Turn the key to START, to start the vehicle.

5. Shift to the drive gear you want.

6. Have the vehicle fixed as soon as you can.

-- push the shift lever all the way into

-- as you maintain brake application. Then

Parking Over Things That Burn

CAUTION:

Things that can burn could touch hot exhaust
parts under your vehicle and ignite. Don’t park
over papers, leaves, dry grass or other things that
can burn.

2-27

yellowblue

Engine Exhaust

CAUTION:

Engine exhaust can kill. It contains the gas
carbon monoxide (CO), which you can’t see or
smell. It can cause unconsciousness and death.

You might have exhaust coming in if:

D

Your exhaust system sounds strange
or different.

D

Your vehicle gets rusty underneath.

D

Your vehicle was damaged in a collision.

D

Your vehicle was damaged when driving over
high points on the road or over road debris.

D

Repairs weren’t done correctly.

D

Your vehicle or exhaust system had been
modified improperly.

If you ever suspect exhaust is coming into
your vehicle:

D

Drive it only with all the windows down to
blow out any CO; and

D

Have your vehicle fixed immediately.

Running Your Engine While
You’re Parked

It’s better not to park with the engine running. But if you
ever have to, here are some things to know.

CAUTION:

Idling the engine with the climate control system
off could allow dangerous exhaust into
your vehicle (see the earlier Caution under
“Engine Exhaust”).

Also, idling in a closed-in place can let deadly
carbon monoxide (CO) into your vehicle even if
the fan switch is at the highest setting. One place
this can happen is a garage. Exhaust
CO

-- can come in easily. NEVER park in a

garage with the engine running.
Another closed-in place can be a blizzard.

(See “Blizzard” in the Index.)

-- with

2-28

CAUTION:

It can be dangerous to get out of your vehicle if
the shift lever is not fully in PARK (P) with the
parking brake firmly set. Your vehicle can roll.
Don’t leave your vehicle when the engine is
running unless you have to. If you’ve left the
engine running, the vehicle can move suddenly.
You or others could be injured. To be sure your
vehicle won’t move, even when you’re on fairly
level ground, always set your parking brake and
move the shift lever to PARK (P).

Follow the proper steps to be sure your vehicle won’t
move. See “Shifting Into PARK (P)” in the Index.

If you are parking on a hill and if you’re pulling a
trailer, also see “Towing a Trailer” in the Index.

yellowblue

Windows

Manual Windows

On a vehicle with manual windows, use the window
crank to open and close each window.

Power Windows (If Equipped)

The power window switches are located on the armrest
of the driver’s door. In addition, each passenger door has
a switch for its own window.

2-29

yellowblue

Auto-Down Switch

The driver’s window switch has an auto
This switch is labeled AUTO. Push the switch back
partway , and the driver’s window will open a small
amount. If the switch is pushed all the way back, the
window will go all the way down.

T o stop the window while it is lowering, move the
switch forward. T o raise the window, move and hold the
switch forward.

-Out-Switch

Lock

The driver’s power window controls also include a lock
out switch. Press LOCK OUT to stop front and rear
passengers from using their window switches. The
driver can still control all the windows with the lock on.
Press the LOCK OUT button again for normal
window operation.

-down feature.

Horn

You can sound the horn by pressing the horn symbol on
your steering wheel.

Tilt Wheel

A tilt steering wheel allows you to adjust the steering
wheel before you drive.

You can also raise it to the highest level to give your
legs more room when you exit and enter the vehicle.

T o tilt the wheel, hold the steering wheel and pull the
lever toward you.

Move the steering wheel to a comfortable level, then
release the lever to lock the wheel in place.

2-30

yellowblue

Turn Signal/Multifunction Lever

The lever on the left side of the steering column
includes your:

D

Turn Signal and Lane Change Indicator

D

Headlamp High/Low-Beam Changer

D

Park Lamps and Headlamps

Turn and Lane Change Signals

The turn signal has two upward (for right) and two
downward (for left) positions. These positions allow you
to signal a turn or a lane change.

To signal a turn, move the lever all the way up or down.
When the turn is finished, the lever will return automatically.

An arrow on the instrument
panel will flash in the
direction of the turn or
lane change.

T o signal a lane change, just raise or lower the lever
until the arrow starts to flash. Hold it there until you
complete your lane change. The lever will return by
itself when you release it.

A warning chime signal will come on if you have left
your turn signal on for more than 3/4 mile (1 km).

As you signal a turn or a lane change, if the arrow
flashes rapidly, a signal bulb may be burned out and
other drivers won’t see your turn signal.

2-31

yellowblue

If a bulb is burned out, replace it to help avoid an
accident. If the arrow doesn’t go on at all when you
signal a turn, check for burned-out bulbs and then check
the fuse (see “Fuses and Circuit Breakers” in the Index).

Headlamp High/Low Beam Changer

T o change the headlamps
from low beam to high
beam, push forward on the
turn signal/multifunction
lever.

T o change the headlamps from high beam to low beam,
pull the turn signal lever toward you. When the high
beams are on, a light on the instrument panel will also
be on.

Flash-to-Pass

This feature lets you use your high-beam headlamps to
signal a driver in front of you that you want to pass.

T o use it, pull the turn signal/multifunction lever toward
you until the high
release the lever to turn them off.

-beam headlamps come on, then

Windshield Wipers

You control the windshield wipers by moving the stalk
with the wiper symbol on it up or down.

For a single wiper cycle, move the stalk down to MIST,
then release it. For more cycles, hold the stalk
down longer.

2-32

yellowblue

For steady wiping at low speed, move the stalk up to the
LO. For high
HI. T o stop the wipers, move the stalk to OFF.

You can set the wiper speed for a long or short
delay between wipes. This can be very useful in light
rain or snow.

Move the stalk to INT, then turn the inner band, labeled
INT ADJ, and choose the delay you want. Turn the inner
band up for shorter delay times between wiper cycles.
Turn the band down for a longer delay time between
wiper cycles.

Remember that damaged wiper blades may prevent you
from seeing well enough to drive safely. To avoid
damage, be sure to clear ice and snow from the wiper
blades before using them. If they’re frozen to the
windshield, carefully loosen or thaw them. If your
blades do become damaged, get new blades or
blade inserts.

Heavy snow or ice can overload your wiper motor. A
circuit breaker will stop the motor until it cools. Clear
away snow or ice to prevent an overload.

-speed wiping, move the stalk up further, to

Windshield Washer

T o wash your windshield, push in the button at the end
of the stalk until the washers begin.

2-33

CAUTION:

In freezing weather, don’t use your washer until
the windshield is warmed. Otherwise the washer
fluid can form ice on the windshield, blocking
your vision.

When you release the button, the washers will stop, but
the wipers will continue to wipe for about three times or
will either stop or will resume the speed you were
using before.

yellowblue

Cruise Control

With cruise control, you can maintain a speed of about
25 mph (40 km/h) or more without keeping your foot on
the accelerator. This can really help on long trips.
Cruise control does not work at speeds below
25 mph (40 km/h).

When you apply your brake, the cruise control shuts off.

2-34

CAUTION:

yellowblue

Setting Cruise Control

D

Cruise control can be dangerous where you
can’t drive safely at a steady speed. So,
don’t use your cruise control on winding
roads or in heavy traffic.

D

Cruise control can be dangerous on
slippery roads. On such roads, fast changes
in tire traction can cause needless wheel
spinning, and you could lose control. Don’t
use cruise control on slippery roads.

CAUTION:

If you leave your cruise control switch on when
you’re not using cruise, you might hit a button
and go into cruise when you don’t want to. You
could be startled and even lose control. Keep the
cruise control switch off until you want to use it.

The cruise control buttons are located on the steering
wheel for your convenience.

1. Press the cruise control OFF/ON button.

2. Get up to the speed you want.

3. Press the SET DECEL button and release it.

4. T ake your foot off the accelerator pedal.

2-35

yellowblue

Resuming a Set Speed

Suppose you set your cruise control at a desired speed
and then you apply the brake. This, of course, shuts off
the cruise control. But you don’t need to reset it. Once
you’re going about 25 mph (40 km/h) or more, you can
press the cruise control ACCEL RESUME button for
about half a second.

You’ll go right back up to your chosen speed and
stay there.

If you press the ACCEL RESUME button longer than
half a second, the vehicle will keep going faster until
you release the switch or apply the brake. So unless you
want to go faster, don’t hold down the ACCEL
RESUME button.

Increasing Speed While Using Cruise Control

There are two ways to go to a higher speed.

D

Use the accelerator pedal to get to the higher speed.
Push the SET DECEL button, then release the button
and the accelerator pedal. You’ll now cruise at the
higher speed.

D

Press the ACCEL RESUME button. Hold it there
until you get up to the speed you want, and then
release the button. T o increase your speed in very
small amounts, press the ACCEL RESUME button
for less than half a second and then release it. Each
time you do this, your vehicle will go about
1 mph (1.6 km/h) faster.

The accelerate feature will only work after you turn on
the cruise control by pushing the SET DECEL button.

2-36

yellowblue

Reducing Speed While Using Cruise Control

There are two ways to reduce your speed while using
cruise control:

D

Push the SET DECEL button until you reach the
lower speed you want, then release it.

D

T o slow down in very small amounts, push the SET
DECEL button for less than half a second. Each time
you do this, you’ll go 1 mph (1.6 km/h) slower.

Passing Another Vehicle While Using Cruise Control

Use the accelerator pedal to increase your speed. When
you take your foot off the pedal, your vehicle will slow
down to the cruise control speed you set earlier.

Using Cruise Control on Hills

How well your cruise control will work on hills depends
upon your speed, load and the steepness of the hills.
When going up steep hills, you may have to step on the
accelerator pedal to maintain your speed. When going
downhill, you may have to brake or shift to a lower gear
to keep your speed down. Of course, applying the brake
takes you out of cruise control. Many drivers find this to
be too much trouble and don’t use cruise control on
steep hills.

Ending Out of Cruise Control

There are two ways to turn off the cruise control:

D

Step lightly on the brake pedal;

D

Press the cruise control OFF/ON button.

Erasing the Cruise Speed Memory

When you turn off the cruise control or the ignition,
your cruise control set speed memory is erased.

2-37

yellowblue

Exterior Lamps

Turn the turn signal lever end cap up one position to
turn on:

D

Parking Lamps

D

Side Marker Lamps

D

T aillamps

D

License Plate Lamps

D

Instrument Panel Lights

Turn the turn signal lever end cap up two positions to
turn on:

D

Headlamps

D

Parking Lamps

D

Sidemarker Lamps

D

T aillamps

D

License Plate Lamps

D

Instrument Panel Lights

Turn the switch to OFF to turn all of the lamps off.

Lamps On Reminder

If you open the driver’s door and turn off the ignition
while leaving the lamps on, you will hear a
warning chime.

2-38

yellowblue

Daytime Running Lamps

Daytime Running Lamps (DRL) can make it easier for
others to see the front of your vehicle during the day.
DRL can be helpful in many different driving
conditions, but they can be especially helpful in the
short periods after dawn and before sunset.

The DRL system will make your low
come on at a reduced brightness when:

D

the ignition is on,

D

the headlamp switch is to OFF or you have turned on
your parking lamps,

D

the light sensor detects daytime light,

D

the parking brake is released and

D

the shift lever is not in PARK (P).

When the DRL system is on, the taillamps, sidemarker,
park lamps and instrument panel lights will not
be illuminated.

The DRL system will remain off any time your vehicle
is in PARK (P) or the parking brake is engaged.

As with any vehicle, you should turn on the regular
headlamp system when you need it.

-beam headlamps

Automatic Light Control (ALC)

When it is dark enough outside, your Automatic Light
Control (ALC) will turn on your headlamps at the
normal brightness along with other lamps such as the
taillamps, sidemarker, park lamps and the instrument
panel lights. The radio lights will also be dim.

Your vehicle is equipped with a light sensor on the top
of the instrument panel under the defroster grill, so be
sure it is not covered which will cause the ALC system
to be on whenever the ignition is on.

The ALC system may also be on when driving through a
parking garage, heavy overcast weather, a tunnel. This
is normal.

There is a delay in the transition between the daytime
and nighttime operation of the DRL and the ALC
systems so that driving under bridges or bright overhead
street lights does not affect the system. The DRL and
ALC systems will only be affected when the light sensor
sees a change in lighting lasting longer than this delay.

T o idle your vehicle with the ALC system off, set the
park brake while the ignition is off. Then start the
vehicle. The ALC system will stay off until you release
the park brake.

As with any vehicle, you should turn on the regular
headlamp system when you need it.

2-39

yellowblue

Fog Lamps

The button for your fog
lamps is on the instrument
panel, to the left of the
steering wheel, beside
the instrument panel
intensity control.

When using fog lamps, the ignition must be on, as well
as the parking lamps or the low

Push the top of the button to turn the fog lamps on. An
indicator light on the button will glow when the fog
lamps are on. Push the top of the button again to turn the
fog lamps off.

The fog lamps will turn off whenever the high
headlamps are turned on. When the high
turned off, the fog lamps will come on again.

-beam headlamps.

-beam

-beams are

Interior Lamps

Instrument Panel Intensity Control

You can brighten or dim the
instrument panel cluster
lights by rotating the switch,
located to the left of the
steering wheel.

Illuminated Entry/Exit System

When you open any door, the lamps inside your vehicle
will go on. These lamps will fade out after about 40
seconds, or when the ignition is turned on after all doors
have been closed. If the ignition was recently turned off,
the lamps will fade out after four seconds. These lamps
will also go on when you press the vehicle symbol or
UNLOCK button on the remote lock control transmitter.

2-40

yellowblue

If the ignition has been off for less than two minutes, the
lamps inside your vehicle will stay on for about 15
seconds after your key is removed from the ignition to
provide an illuminated exit.

Mirror Reading Lamps

Press the switch on the lower front portion of the mirror
to turn on the lamp. Press the other side of the switch to
turn the lamp off.

Three-Position Dome Lamp

The switch on this lamp has three positions. The ON
position will turn on the light. The DOOR position will
turn on the light whenever a door is opened. The OFF
position will shut off the lamp completely, even when a
door is opened.

Trunk Lamp

The trunk lamp comes on when you open your trunk.

Battery Saver

Your vehicle is equipped with a battery saver feature
designed to protect your vehicle’s battery.

When any interior lamp (trunk, reading, footwell or
glove box) is left on when the ignition is turned off, the
battery saver system will automatically shut the lamp off
after 20 minutes. This will avoid draining the battery.

T o reactivate the interior lamps, either:

D

the ignition must be turned on,

D

the activated lamp switch must be turned off and
then on or

D

a front door must be opened.

The battery saver feature will also be activated when
any door of your vehicle is left open.

2-41

yellowblue

Mirrors

Inside Day/Night Rearview Mirror

This mirror can be adjusted two ways. First, to adjust
the angle of the mirror, move the mirror to a position
that allows you see out the back window. To adjust the
height of the mirror, adjust the arm that connects the
mirror to the windshield.

T o reduce glare from lights behind you, move the lever
toward you to the night position.

Manual Remote Control Mirror

The outside rearview mirror should be adjusted so you
can just see the side of your vehicle when you are sitting
in a comfortable driving position.

Adjust the driver’s side
outside mirror with the
control lever on the
driver’s door.

T o adjust your passenger’s side mirror, sit in the driver’s
seat and have a passenger adjust the mirror for you.

2-42