Oldsmobile Cutlass 1995 Ciera Cruiser 2.2L Workshop Manual

oldsmobile :: Oldsmobile Cutlass Ciera Cruiser L4

-2.2L VIN 4 (1995)

> Relays and Modules > Relays and Modules - Accessories and Optional Equipment > Antenna Relay > Component Information > Locations > Component Locations

Behind Center Of I/P

> Relays and Modules > Relays and Modules - Accessories and Optional Equipment > Antenna Relay > Component Information > Locations > Component Locations > Page 8

Behind RH Side Of I/P

> Relays and Modules > Relays and Modules - Accessories and Optional Equipment > Emergency Contact Module > Component Information > Technical Service Bulletins > OnStar(R) - Aftermarket Device Interference

Information

Emergency Contact Module: Technical Service BulletinsOnStar(R) - Aftermarket Device Interference Information

INFORMATION
Bulletin No.: 08-08-46-004
Date: August 14, 2008

Subject: Information on Aftermarket Device Interference with OnStar(R) Diagnostic Services

Models:2009 and Prior GM Passenger Car and Truck (including Saturn)2009 and Prior HUMMER H2, H3 Models2009 and Prior Saab 9-7X
with OnStar(R) (RPO UE1)

This bulletin is being issued to provide dealer service personnel with information regarding aftermarket devices connected to the Diagnostic LinkConnector (DLC) and the impact to OnStar(R) diagnostic probes and Vehicle Diagnostic e-mails.

Certain aftermarket devices, when connected to the Diagnostic Link Connector, such as, but not limited to, Scan Tools, Trip Computers, Fuel EconomyAnalyzers and Insurance Tracking Devices, interfere with OnStar's ability to perform a diagnostic probe when requested (via a blue button call) by asubscriber. These devices also prohibit the ability to gather diagnostic and tire pressure data for a subscriber's scheduled OnStar(R) Vehicle Diagnostic(OVD) e-mail.

These aftermarket devices utilize the Vehicles serial data bus to perform data requests and/or information gathering. When these devices are requestingdata, OnStar(R) is designed not to interfere with any data request being made by these devices as required by OBD II regulations.

The OnStar(R) advisor is unable to definitively detect the presence of these devices and will only be able to inform the caller or requester of theunsuccessful or incomplete probe and may in some cases refer the subscriber/requester to take the vehicle to a dealer for diagnosis of the concern.

When performing a diagnostic check for an unsuccessful or incomplete OnStar(R) diagnostic probe, or for concerns regarding completeness of theOnStar(R) Vehicle Diagnostic (OVD) e-mail, verify that an aftermarket device was not present at the time of the requested probe. Regarding the OVDe-mail, if an aftermarket device is interfering (including a Scan Tool of any type), the e-mail will consistently display a "yellow" indication in diagnosticssection for all vehicle systems except the OnStar(R) System and Tire Pressure data (not available on all vehicles) will not be displayed (i.e. section iscollapsed). Successful diagnostic probes and complete OVD e-mails will resume following the removal or disconnecting of the off-board device.

Disclaimer

> Relays and Modules > Relays and Modules - Accessories and Optional Equipment > Keyless Entry Module > Component Information > Locations

LH Side Of Luggage Compartment

> Relays and Modules > Relays and Modules - Accessories and Optional Equipment > Keyless Entry Module > Component Information > Locations > Page 16

Keyless Entry Module: Diagrams

8-Way F Metri-Pack 150 Series BLU

8-Way F Metri-Pack 280 Series BLK

Remote Keyless Entry (RKE) Module

> Relays and Modules > Relays and Modules - Accessories and Optional Equipment > Relay Module > Component Information > Technical Service Bulletins > Customer Interest for Relay Module: > 09-06-03-004D > Dec > 10

> Electrical - MIL ON/DTC's Set By Various Control Modules

Relay Module: Customer InterestElectrical - MIL ON/DTC's Set By Various Control Modules
TECHNICAL

09-06-03-004DBulletin No.:

December 08, 2010Date:

Subject:

Intermittent No Crank/No Start, No Module Communication, MIL, Warning Lights, Vehicle Messages or DTCs Set by Various ControlModules - Diagnosing and Repairing Fretting Corrosion (Disconnect Affected Connector and Apply Dielectric Lubricant)

Models:

2011 and Prior GM Passenger Cars and Trucks

Attention:

This repair can be applied to ANY electrical connection including, but not limited to: lighting, body electrical, in-line connections, powertrain controlsensors, etc. DO NOT over apply lubricant to the point where it prevents the full engagement of sealed connectors. A light coating on the terminalsurfaces is sufficient to correct the condition.

Supercede:This bulletin is being revised to update the Attention statement and add the 2011 model year. Please discard Corporate Bulletin Number 09-06-03-004C(Section 06 - Engine/Propulsion System).

Condition

Some customers may comment on any of the following conditions:

- An intermittent no crank/no start

- Intermittent malfunction indicator lamp (MIL) illumination

- Intermittent service lamp illumination

- Intermittent service message(s) being displayed

The technician may determine that he is unable to duplicate the intermittent condition.

Cause

- Vibration

- Thermal cycling

- Poor connection/terminal retention

- Micro motion

- A connector, component or wiring harness not properly secured resulting in movement
On low current signal circuits this condition may cause high resistance, resulting in intermittent connections.
On high current power circuits this condition may cause permanent increases in the resistance and may cause a device to become inoperative.

Representative List of Control Modules and Components

> Relays and Modules > Relays and Modules - Accessories and Optional Equipment > Relay Module > Component Information > Technical Service Bulletins > Customer

Interest for Relay Module: > 09-06-03-004D > Dec > 10 > Electrical - MIL ON/DTC's Set By Various Control Modules > Page 25

Cutlass Ciera Cruiser L4-2.2L VIN 4 (1995)

This condition may be caused by a buildup of nonconductive insulating oxidized debris known as fretting corrosion, occurring between two electricalcontact surfaces of the connection or connector. This may be caused by any of the following conditions:

The following is only a representative list of control modules and components that may be affected by this connection or connector condition and include every possible module or component for every vehicle. DOESNOT

- Blower Control Module

- Body Control Module (BCM)

- Communication Interface Module (CIM)

- Cooling Fan Control Module

- Electronic Brake Control Module (EBCM)

- Electronic Brake and Traction Control Module (EBTCM)

- Electronic Suspension Control (ESC) Module

- Engine Control Module (ECM)

- Heating, Ventilation and Air Conditioning (HVAC) Control Module

- HVAC Actuator

- Inflatable Restraint Sensing and Diagnostic Module (SDM)

- Any AIR BAG module

- Seatbelt Lap Anchor Pretensioner

- Seatbelt Retractor Pretensioner

- An SIR system connection or connector condition resulting in the following DTCs being set: B0015, B0016, B0019, B0020, B0022, or B0023

- Powertrain Control Module (PCM)

- Remote Control Door Lock Receiver (RCDLR)

- Transmission Control Module (TCM)

Correction

replace the control module, wiring or component for the following conditions: ImportantDO NOT

-

be duplicated. The condition is intermittent and cannot

-

be duplicated. The condition is present and by disconnecting and reconnecting the connector the condition can no longer

Use the following procedure to correct the conditions listed above.

1. Install a scan tool and perform the Diagnostic System Check - Vehicle. Retrieve and record any existing history or current DTCs from all of the

control modules (refer to SI).
If any DTC(s) are set, refer to Diagnostic Trouble Code (DTC) List - Vehicle to identify the connector(s) of the control module/component

which may be causing the condition (refer to SI).

If DTCs are not set, refer to Symptoms - Vehicle to identify the connector(s) of the control module/component which may be causing the

condition (refer to SI).

2. When identified, use the appropriate DTC Diagnostics, Symptoms, Schematics, Component Connector End Views and Component Locator

documents to locate and disconnect the affected harness connector(s) which are causing the condition.

ImportantDO NOT

apply an excessive amount of dielectric lubricant to the connectors as shown, as hydrolock may result when attempting to mate theconnectors. Use ONLY a clean nylon brush that is dedicated to the repair of the conditions in this bulletin.

3. With a one-inch nylon bristle brush, apply dielectric lubricant to both the module/component side and the harness side of the affected connector(s).

4. Reconnect the affected connector(s) and wipe away any excess lubricant that may be present. 5. Attempt to duplicate the condition by using the following information:

> Relays and Modules > Relays and Modules - Accessories and Optional Equipment > Relay Module > Component Information > Technical Service Bulletins > Customer

Interest for Relay Module: > 09-06-03-004D > Dec > 10 > Electrical - MIL ON/DTC's Set By Various Control Modules > Page 26

Cutlass Ciera Cruiser L4-2.2L VIN 4 (1995)

Note

Fretting corrosion looks like little dark smudges on electrical terminals and appear where the actual electrical contact is being made. In less severecases it may be unable to be seen or identified without the use of a magnifying glass.

- DTC Diagnostic Procedure

- Circuit/System Description

- Conditions for Running the DTC

- Conditions for Setting the DTC

- Diagnostic Aids

- Circuit/System Verification

If the condition cannot be duplicated, the repair is complete. If the condition can be duplicated, then follow the appropriate DTC, Symptom or Circuit/System Testing procedure (refer to SI).

Repair Order Documentation

be documented on the repair order. Failure to do so may result in a chargeback.ImportantThe following information MUST

- Customer vehicle condition.

- Was a Service Lamp or Service Message illuminated? If yes, specify which Service Lamp or Service Message.

- Was a DTC(s) set? If yes, specify which DTC(s) were set.

- After following the procedure contained within this bulletin, could the condition be duplicated?

If the condition duplicated, then document the affected module/component connector name and number on the repair order. was not

-

was

If the condition duplicated after the procedure contained within this bulletin was followed, and additional diagnosis led to the replacement ofa module or component, the SI Document ID Number be written on the repair order. MUST

Parts Information

Alternate Distributor For All of North America
Note

NyoGel(R) 760G Lubricant* is equivalent to GMSPO P/N 12377900, and P/N 10953529 (Canada), specified for use to correct the condition in thisbulletin.

*We believe this source and their products to be reliable. There may be additional manufacturers of such products/materials. General Motors does notendorse, indicate any preference for, or assume any responsibility for the products or material from this firm or for any such items that may be availablefrom other sources.

Warranty Information (excluding Saab Models)

For vehicles repaired under warranty, use the appropriate/closest labor operation depending upon the module/component connection that the dielectriclubricant was applied to:

> Relays and Modules > Relays and Modules - Accessories and Optional Equipment > Relay Module > Component Information > Technical Service Bulletins > Customer

Interest for Relay Module: > 09-06-03-004D > Dec > 10 > Electrical - MIL ON/DTC's Set By Various Control Modules > Page 27

Cutlass Ciera Cruiser L4-2.2L VIN 4 (1995)

Warranty Information (Saab Models)

For vehicles repaired under warranty, use the appropriate/closest labor operation depending upon the module/component connection that the dielectriclubricant was applied to refer to the table above.

Disclaimer

> Relays and Modules > Relays and Modules - Accessories and Optional Equipment > Relay Module > Component Information > Technical Service Bulletins > All Technical Service Bulletins for Relay Module: > 09-06-03-

004D > Dec > 10 > Electrical - MIL ON/DTC's Set By Various Control Modules

Relay Module: All Technical Service BulletinsElectrical - MIL ON/DTC's Set By Various Control Modules
TECHNICAL

09-06-03-004DBulletin No.:

December 08, 2010Date:

Subject:

Intermittent No Crank/No Start, No Module Communication, MIL, Warning Lights, Vehicle Messages or DTCs Set by Various ControlModules - Diagnosing and Repairing Fretting Corrosion (Disconnect Affected Connector and Apply Dielectric Lubricant)

Models:

2011 and Prior GM Passenger Cars and Trucks

Attention:

This repair can be applied to ANY electrical connection including, but not limited to: lighting, body electrical, in-line connections, powertrain controlsensors, etc. DO NOT over apply lubricant to the point where it prevents the full engagement of sealed connectors. A light coating on the terminalsurfaces is sufficient to correct the condition.

Supercede:This bulletin is being revised to update the Attention statement and add the 2011 model year. Please discard Corporate Bulletin Number 09-06-03-004C(Section 06 - Engine/Propulsion System).

Condition

Some customers may comment on any of the following conditions:

- An intermittent no crank/no start

- Intermittent malfunction indicator lamp (MIL) illumination

- Intermittent service lamp illumination

- Intermittent service message(s) being displayed
The technician may determine that he is unable to duplicate the intermittent condition.

Cause

- Vibration

- Thermal cycling

- Poor connection/terminal retention

- Micro motion

- A connector, component or wiring harness not properly secured resulting in movement
On low current signal circuits this condition may cause high resistance, resulting in intermittent connections.
On high current power circuits this condition may cause permanent increases in the resistance and may cause a device to become inoperative.

Representative List of Control Modules and Components

> Relays and Modules > Relays and Modules - Accessories and Optional Equipment > Relay Module > Component Information > Technical Service Bulletins > All Technical

Service Bulletins for Relay Module: > 09-06-03-004D > Dec > 10 > Electrical - MIL ON/DTC's Set By Various Control Modules > Page 33

Cutlass Ciera Cruiser L4-2.2L VIN 4 (1995)

This condition may be caused by a buildup of nonconductive insulating oxidized debris known as fretting corrosion, occurring between two electricalcontact surfaces of the connection or connector. This may be caused by any of the following conditions:

The following is only a representative list of control modules and components that may be affected by this connection or connector condition and include every possible module or component for every vehicle. DOESNOT

- Blower Control Module

- Body Control Module (BCM)

- Communication Interface Module (CIM)

- Cooling Fan Control Module

- Electronic Brake Control Module (EBCM)

- Electronic Brake and Traction Control Module (EBTCM)

- Electronic Suspension Control (ESC) Module

- Engine Control Module (ECM)

- Heating, Ventilation and Air Conditioning (HVAC) Control Module

- HVAC Actuator

- Inflatable Restraint Sensing and Diagnostic Module (SDM)

- Any AIR BAG module

- Seatbelt Lap Anchor Pretensioner

- Seatbelt Retractor Pretensioner

- An SIR system connection or connector condition resulting in the following DTCs being set: B0015, B0016, B0019, B0020, B0022, or B0023

- Powertrain Control Module (PCM)

- Remote Control Door Lock Receiver (RCDLR)

- Transmission Control Module (TCM)

Correction

replace the control module, wiring or component for the following conditions: ImportantDO NOT

-

be duplicated. The condition is intermittent and cannot

-

be duplicated. The condition is present and by disconnecting and reconnecting the connector the condition can no longer

Use the following procedure to correct the conditions listed above.

1. Install a scan tool and perform the Diagnostic System Check - Vehicle. Retrieve and record any existing history or current DTCs from all of the

control modules (refer to SI).
If any DTC(s) are set, refer to Diagnostic Trouble Code (DTC) List - Vehicle to identify the connector(s) of the control module/component

which may be causing the condition (refer to SI).

If DTCs are not set, refer to Symptoms - Vehicle to identify the connector(s) of the control module/component which may be causing the

condition (refer to SI).

2. When identified, use the appropriate DTC Diagnostics, Symptoms, Schematics, Component Connector End Views and Component Locator

documents to locate and disconnect the affected harness connector(s) which are causing the condition.

ImportantDO NOT

apply an excessive amount of dielectric lubricant to the connectors as shown, as hydrolock may result when attempting to mate theconnectors. Use ONLY a clean nylon brush that is dedicated to the repair of the conditions in this bulletin.

3. With a one-inch nylon bristle brush, apply dielectric lubricant to both the module/component side and the harness side of the affected connector(s).

4. Reconnect the affected connector(s) and wipe away any excess lubricant that may be present. 5. Attempt to duplicate the condition by using the following information:

> Relays and Modules > Relays and Modules - Accessories and Optional Equipment > Relay Module > Component Information > Technical Service Bulletins > All Technical

Service Bulletins for Relay Module: > 09-06-03-004D > Dec > 10 > Electrical - MIL ON/DTC's Set By Various Control Modules > Page 34

Cutlass Ciera Cruiser L4-2.2L VIN 4 (1995)

Note

Fretting corrosion looks like little dark smudges on electrical terminals and appear where the actual electrical contact is being made. In less severecases it may be unable to be seen or identified without the use of a magnifying glass.

- DTC Diagnostic Procedure

- Circuit/System Description

- Conditions for Running the DTC

- Conditions for Setting the DTC

- Diagnostic Aids

- Circuit/System Verification

If the condition cannot be duplicated, the repair is complete. If the condition can be duplicated, then follow the appropriate DTC, Symptom or Circuit/System Testing procedure (refer to SI).

Repair Order Documentation

be documented on the repair order. Failure to do so may result in a chargeback.ImportantThe following information MUST

- Customer vehicle condition.

- Was a Service Lamp or Service Message illuminated? If yes, specify which Service Lamp or Service Message.

- Was a DTC(s) set? If yes, specify which DTC(s) were set.

- After following the procedure contained within this bulletin, could the condition be duplicated?

If the condition duplicated, then document the affected module/component connector name and number on the repair order. was not

-

was

If the condition duplicated after the procedure contained within this bulletin was followed, and additional diagnosis led to the replacement ofa module or component, the SI Document ID Number be written on the repair order. MUST

Parts Information

Alternate Distributor For All of North America
Note

NyoGel(R) 760G Lubricant* is equivalent to GMSPO P/N 12377900, and P/N 10953529 (Canada), specified for use to correct the condition in thisbulletin.

*We believe this source and their products to be reliable. There may be additional manufacturers of such products/materials. General Motors does notendorse, indicate any preference for, or assume any responsibility for the products or material from this firm or for any such items that may be availablefrom other sources.

Warranty Information (excluding Saab Models)

For vehicles repaired under warranty, use the appropriate/closest labor operation depending upon the module/component connection that the dielectriclubricant was applied to:

> Relays and Modules > Relays and Modules - Accessories and Optional Equipment > Relay Module > Component Information > Technical Service Bulletins > All Technical

Service Bulletins for Relay Module: > 09-06-03-004D > Dec > 10 > Electrical - MIL ON/DTC's Set By Various Control Modules > Page 35

Cutlass Ciera Cruiser L4-2.2L VIN 4 (1995)

Warranty Information (Saab Models)

For vehicles repaired under warranty, use the appropriate/closest labor operation depending upon the module/component connection that the dielectriclubricant was applied to refer to the table above.

Disclaimer

> Relays and Modules > Relays and Modules - Body and Frame > Keyless Entry Module > Component Information > Locations

LH Side Of Luggage Compartment

> Relays and Modules > Relays and Modules - Body and Frame > Keyless Entry Module > Component Information > Locations > Page 40

Keyless Entry Module: Diagrams

8-Way F Metri-Pack 150 Series BLU

8-Way F Metri-Pack 280 Series BLK

Remote Keyless Entry (RKE) Module

> Relays and Modules > Relays and Modules - Body and Frame > Power Door Lock Control Module > Component Information > Locations

Power Door Lock Control Module: Locations

Behind LH Side Of I/P

The Auto Unlock Module is located behind LH side of I/P.

> Relays and Modules > Relays and Modules - Body and Frame > Power Door Lock Control Module > Component Information > Locations > Page 44

6-Way PC Edgeboard BEIGE (Auto Door Unlock Module)

> Relays and Modules > Relays and Modules - Body and Frame > Power Door Lock Relay > Component Information > Locations

Power Door Lock Relay: Locations

RH Shroud And Door

The Door Lock Relay Assembly is located on the RH shroud.

> Relays and Modules > Relays and Modules - Body and Frame > Power Door Lock Relay > Component Information > Locations > Page 48

6-Way F Metri-Pack 280 Series BLK (Door Lock Relay)

> Relays and Modules > Relays and Modules - Body and Frame > Trunk / Liftgate Relay > Component Information > Locations

Behind Center Of I/P

> Relays and Modules > Relays and Modules - Body and Frame > Trunk / Liftgate Relay > Component Information > Locations > Page 52

4-way F Micro-pack 280,480 Series BLK (Release Relay)

> Relays and Modules > Relays and Modules - Brakes and Traction Control > ABS Main Relay > Component Information > Locations

RH Rear Of Engine Compartment

> Relays and Modules > Relays and Modules - Brakes and Traction Control > ABS Main Relay > Component Information > Locations > Page 57

4-Way F Metri-Pack 280 FLXLK GRY (Electronic Brake Control Relay)

> Relays and Modules > Relays and Modules - Brakes and Traction Control > Brake Fluid Solenoid Valve Relay > Component Information > Locations > Component Locations

LH Rear Of Engine Compartment

> Relays and Modules > Relays and Modules - Brakes and Traction Control > Brake Fluid Solenoid Valve Relay > Component Information > Locations > Component Locations > Page 62

LH Rear Of Engine Compartment

> Relays and Modules > Relays and Modules - Brakes and Traction Control > Electronic Brake Control Module > Component Information > Locations > EBCM Independent Lamp Driver Module

Behind LH Side Of I/P

> Relays and Modules > Relays and Modules - Brakes and Traction Control > Electronic Brake Control Module > Component Information > Locations > EBCM Independent Lamp Driver Module > Page 67

Behind RH Side Of I/P

> Relays and Modules > Relays and Modules - Brakes and Traction Control > Electronic Brake Control Module > Component Information > Diagrams > C1

Electronic Brake Control Module: DiagramsC1

32-Way F Micro-Pack 100 Series BLU

> Relays and Modules > Relays and Modules - Brakes and Traction Control > Electronic Brake Control Module > Component Information > Diagrams > C1 > Page 70

Cutlass Ciera Cruiser L4-2.2L VIN 4 (1995)

Electronic Brake Control Module (EBCM)

Electronic Brake Control Module (EBCM)

> Relays and Modules > Relays and Modules - Brakes and Traction Control > Electronic Brake Control Module > Component Information > Diagrams > C1 > Page 71

Electronic Brake Control Module: DiagramsC2

8-Way F Metri-Pack 280 Series GRA

Electronic Brake Control Module (EBCM)

> Relays and Modules > Relays and Modules - Brakes and Traction Control > Electronic Brake Control Module > Component Information > Diagrams > C1 > Page 72

Cutlass Ciera Cruiser L4-2.2L VIN 4 (1995)

Electronic Brake Control Module (EBCM)

> Relays and Modules > Relays and Modules - Brakes and Traction Control > Electronic Brake Control Module > Component Information > Diagrams > Page 73

Electronic Brake Control Module: Description and Operation
DESCRIPTION

The ABS system is controlled by a microprocessor based Electronic Brake Control Module (EBCM). Inputs to the system include four wheelspeed sensors, brakes, ignition switch and unswitched battery voltage. Outputs include three bi-directional motor controls, three lamp controls, twosolenoid controls and the system enable relay. A serial data line, located in terminal 9 of the Data Link Connector (DLC), is provided for servicediagnostic tools and assembly plant testing.

The EBCM monitors the speed of each wheel. If any wheel begins to approach lock-up and the brake switch is on, the EBCM controls the motorsand solenoids to reduce brake pressure to the wheel approaching lock-up. Once the wheel regains traction, brake pressure is increased until wheelbegins to approach lock-up. This cycle repeats until either vehicle comes to a stop, the brake is released or no wheels approach lock-up.Additionally, the EBCM monitors itself, each input and each output for proper operation. If any system fault is detected, the EBCM will store aDTC in nonvolatile memory.

On a EBTCM, the ABS portion of the module operates the same as a EBCM. A EBTCM is used if the vehicle is equipped with either theEnhanced Traction System (ETS) or Traction Control System (TCS). The ETS or TCS portion of the EBTCM monitors wheel spin slip throughthe drive wheels speed sensors. If the wheels begin to slip, the EBTCM determines the desired wheel torque needed to minimize wheel slip. Thisinformation is sent to the PCM through the Serial data link. On models equipped w/ETS, the PCM controls engine torque by ignition retard andtransmission shifts. On models equipped w/TCS, the PCM controls engine torque by ignition retard, transmission shifts and applies brakes severaltimes until the vehicle regains traction. Once the vehicle regains traction, brake pressure is decreased and engine torque reduction is no longerrequested. This cycle repeats until traction control is no longer necessary.

> Relays and Modules > Relays and Modules - Brakes and Traction Control > Electronic Brake Control Module > Component Information > Diagrams > Page 74

Electronic Brake Control Module: Service and Repair

Fig. 800 EBCM Assembly Removal.

Fig.800

1. Disconnect EBCM electrical connectors, .2. Remove ECU to dash panel attaching screws, then the ECU from dash panel.3. Reverse procedure to install, noting the following:

a. Ensure plastic grommets, if equipped, are located properly.b. Bleed brake system as described under . See: Brakes and Traction Control/Brake BleedingBrake System Bleed

> Relays and Modules > Relays and Modules - Cooling System > Radiator Cooling Fan Motor Relay > Component Information > Locations

RH Front Of Engine Compartment

> Relays and Modules > Relays and Modules - Cruise Control > Cruise Control Module > Component Information > Locations

LH Side Of Engine Compartment

> Relays and Modules > Relays and Modules - Cruise Control > Cruise Control Module > Component Information > Locations > Page 83

Cruise Control Module: Diagrams

10-Way F Metri-pack 150 Series BLK Cruise Control Module

10-way F Metri-Pack 150 Series BLK (Cruise Control Module)

> Relays and Modules > Relays and Modules - Cruise Control > Cruise Control Module > Component Information > Locations > Page 84

Cruise Control Module: Description and Operation
OPERATION

The module will interpret the position of the servo, the position of the control switches and the output of the speed sensor. In response to these inputs,the module electrically signals the opening or closing of the vent and vacuum solenoid valves in the servo.

The module is mounted on the dash support bracket at the right side of the steering column, but is integral with the ECM on some models with certainengines.

> Relays and Modules > Relays and Modules - HVAC > Blower Motor Relay > Component Information > Locations

RH Front Of Engine Compartment

> Relays and Modules > Relays and Modules - HVAC > Blower Motor Relay > Component Information > Locations > Page 89

Blower Relay, Fuel Pump Relay

> Relays and Modules > Relays and Modules - HVAC > Compressor Clutch Relay > Component Information > Locations

RH Front Of Engine Compartment

> Relays and Modules > Relays and Modules - HVAC > Compressor Clutch Relay > Component Information > Locations > Page 93

4-Way F Metri-Pack 280 FLX LK GRY (A/C Compressor Control Relay Primary Coolant Fan Relay Pusher Coolant Fan Relay)

> Relays and Modules > Relays and Modules - Instrument Panel > Audible Warning Device Control Module > Component Information > Locations

Audible Warning Device Control Module: Locations

Behind RH Side Of I/P

The Seat Belt/Ignition Key/Lamp and Turn Signal Alarm is located in the Convenience Center. The Convenience Center is located behind RH side ofI/P, right of instrument panel Compartment.

> Relays and Modules > Relays and Modules - Instrument Panel > Lamp Driver Module <--> [Panel Illumination Control Module] > Component Information > Diagrams

6-Way PC Edgeboard-STD GRN (Lamp Driver Module)

> Relays and Modules > Relays and Modules - Instrument Panel > Speedometer Module > Component Information > Description and Operation

Speedometer Module: Description and Operation

(VSS) PCM

The Vehicle Speed Sensor generates a signal that indicates the speed of the solid state to supply inputs to the Cruise Control Module,Speedometer and Odometer.

The Vehicle Speed Sensor is mounted in the Transaxle. A magnet rotates near a coil, producing voltage pulses in the coil. The frequency of the ACvoltage coming from this coil depends on the vehicle speed. The VSS sends pulses to the PCM at the rate of pulses per mile.40,000

The PCM takes the voltage pulses from the sensor and uses them to close a solid state output switch. The output terminal is switched to ground at a ratethat is proportional to the speed of the vehicle. The Speedometer and Odometer are switched at pulses per mile.4,000

> Relays and Modules > Relays and Modules - Lighting and Horns > Daytime Running Lamp Control Unit > Component Information > Locations

Daytime Running Lamp Control Unit: Locations

Behind LH Side Of I/P

> Relays and Modules > Relays and Modules - Lighting and Horns > Daytime Running Lamp Control Unit > Component Information > Locations > Page 108

Cutlass Ciera Cruiser L4-2.2L VIN 4 (1995)

Behind Center Of I/P

> Relays and Modules > Relays and Modules - Lighting and Horns > Daytime Running Lamp Control Unit > Component Information > Locations > Page 109

Daytime Running Lamp Control Unit: Diagrams

8-Way F Metri-Pack 280 Series BLK (Daytime Running Lights) DRL Module

8-Way F Metri-Pack 150 Series BLU (Daytime Running Lights) DRL Module

Daytime Running Light (DRL) Module

> Relays and Modules > Relays and Modules - Lighting and Horns > Horn Relay > Component Information > Locations

Horn Relay: Locations

Behind RH Side Of I/P

The Horn Relay is located in the Convenience Center. the Convenience Center is located behind RH side of I/P, right of instrument panel compartment.

> Relays and Modules > Relays and Modules - Power and Ground Distribution > Relay Box > Component Information > Locations > Convenience Center

Relay Box: LocationsConvenience Center

CONVENIENCE CENTER

Behind RH Side Of I/P

The Convenience Center is located behind right hand side of instrument panel.

> Relays and Modules > Relays and Modules - Power and Ground Distribution > Relay Box > Component Information > Locations > Convenience Center > Page 118

Relay Box: LocationsRelay Center

The relay center is located at the front righthand side of the engine compartment.