Oklahoma Sound 6010 User Manual

OklahOma SOund COrpOratiOn

OPTIONAL / ADDITIONAL EQUIPMENT

BRASS READING LAMP / #BRL

Attach an elegant brushed brass reading lamp to
the reading table of your new Speaker Stand. Not
only will you shed light on the subject, but you will
add pizzaz to your new stand.

RECHARGEABLE BATTERY / #PS12V

Connect this 12V 5 amp rechargeable battery
pack with included cable to any of our lecterns
for battery power. 20 hour life. Lecterns recharge
battery overnight.

ARISTOCRAT CONTOUR
FLOOR LECTERN / #600

The perfect lectern for the most demanding,
upscale look in your conference, training
and formal meeting rooms. Contoured
style with radius curves. Available in three
woodgrain thermofused melamine laminate
on MDF. Two built in shelves and our side
mounted slide-out shelf for A/V presentation
equipment. Accented by attractive T-mold
edging. Moves eortlessly on four easy roll
castors, two locking. Ready to assemble.

Dimensions: 23" W x 46½" H x 16" D

Walnut, Lt. Oak, Med. Oak, Mahogany.

#BRL

#PS12V

ARISTOCRAT

Sound Floor Lectern

ASSEMBLY MANUAL

ARISTOCRAT CONTOUR
TABLE TOP LECTERN / #60

Same upscale styling as its full oor sister, but
in an easy-go table top version. Move this at­tractive, aordable lectern from room to room
and keep your notes in order and your audi­ences wowed. Made of thermofused laminate
in four color selections with T-mold edging.
Protective non marring glides included.
Assembly required.

Dimensions: 25" W x 15" H x 20" D

Walnut, Lt. Oak, Med. Oak, Mahogany

For these products please contact your dealer
or Oklahoma Sound Corp.

OKLAHOMA SOUND CORP.

149 Entin Road, Clifton, NJ 07014

Tel [phone] • Fax [phone]

www.oklahomasound.com • email: [e-mail]

#600

#60

MODEL #6010

OklahOma SOund COrpOratiOn

INTRODUCTION

Aristocrat Sound lectern - Model 6010

Perfect for the smallest to largest venues. Executive style podium includes
50 watt multimedia amplier with two built in 8" speakers surrounded by
gold appointments. Includes Microphones, Holders, Digital Timepiece and
rolls on four casters. For audiences up to 2,500 people. Assembly required.

Colors: Walnut, Light Oak, Med. Oak, Mahogany/Black Edging

ARISTOCRAT SOUND FLOOR LECTERN: Model 6010

Dimensions: 25¼" W x 46" H x 20¼" D.

ASSEMBLY TIPS

• Do not use a sharp instrument such as a knife or a screwdriver to open the
packaging, as this may scratch or possibly damage the unit.

• All assembly should be done on a clean protected surface such as carpet
or the like.

• Make sure that you have all the required parts. A list of all the parts
is included.

• Read instructions carefully and follow diagrams to ensure easy and
correct assembly.

CARE OF YOUR CABINET

• All exterior and interior exposed surfaces are melamine covered as well as

edges in matching patterned melamine material. To refresh the appear­ance, wipe the surface with a cloth soaked lightly in furniture oil. Avoid
speaker grill area Your cabinet will look as good as new.

TECHNICAL SPECIFICATIONS

Power Output .......50W RMS at 10% THD

Mic ............................Electret Condenser Mic (2)

Aux ............................150 mV>220K

Frequency ..............100HZ-25KHZ

Response ................+ 3dB

Power Supply ....110-120V ohms DC 10.8 12V

Fuse ......................2A normal

Output .................8 ohms

Accessories ........Handheld mic; clip-on mic;

gooseneck; Shockmount
mic holder; digital clock

Manufacturers Warranty

Our lectern undergoes the most rigid and exacting tests for superior quality and performance before
leaving the factory. Our lectern is made in America by American craftsmen. Oklahoma Sound
Corporation warrants this product to be free from defective material and workmanship for two years
from the date of resale by an authorized Oklahoma Sound distributor. Oklahoma Sound will replace
defective parts and repair malfunctioning products under this warranty when the defect occurs under
normal installation and use, provided the unit is returned to our factory via prepaid transporta­tion after direct authorization and approval by Oklahoma Sound. is warranty provides that
examination of the returned product must disclose in our judgement, a manufacturing defect. is
warranty does not extend to any product which has been subject to misuse, neglect, accident, improper
installation, or where the serial number has been removed or defected and is given in lieu of any other
warranty implied or expressed and will not cover any consequential damages.

700 Series Amplier Operating Instructions

Operating Precautions

Before operating the amplier, be sure you fully understand all instructions and
features of the amplier. DO NOT turn amplier on until all input and output
connections have been made. NEVER replace fuses unless power is o.

Microphone Input Connection

The microphone input accepts ¼" phone jack. Do not position microphone next
to or facing speakers. This may cause acoustic feedback.

Auxiliary Input

One auxiliary input is provided for radio tune; tape recorder, CD player or multi­media equipment. Output level is adjusted by the auxiliary volume control.

Tone/Equalization Controls

The Low and High frequency controls are similar to the bass and treble controls
found on most stereo systems. Optimum tone is achieved by rst setting both
knobs halfway; adjust Low and High frequency controls to suit environment.

Power Supply 12V DC Operation

Connect a 12 volt rechargeable battery 5 amp (not included) to the battery
input connector located on the panel of the amplier (using 6' battery cable).
Be sure that the positive pole of battery is connected to the white wire terminal
(+) and the negative pole to the Brass wire (-). When lectern is plugged into a
standard wall outlet, the battery will automatically recharge. Green indicator
light illuminates during recharge mode.

Precautions

• Set Mic volume control on lowest when turning unit on.

• Ensure correct polarity for D.C. supply connections.

• Reverse connections will blow the fuse and may damage internal circuitry.

• Always replace fuse with specied rating.

Removal and Installation of Amplier

If your amplier has to be removed for servicing — follow these simple steps:

1) Disconnect A/C wall plug.

2) Remove 4 side screws two on each side panel under amp top.

3) Disconnect speaker wire at rear of amplier.

4) Pack it into a strong box with ample cushioning and return to factory

5) To install new amplier reverse the above procedure.

2 7