O.K.I. usa WDS-HDR1527DN, WDS-HDR1527DNP Operating Manual
OPERATING MANUAL
Before attempting to connect or operate this product, please read these instructions
completely
Hyper Dynamic Range
WDS-HDR1527DN
WDS-HDR1527DNP
Day & Night OLPF Removable
DIGITAL COLOR VIDEO CAMERA
ON-SCREEN-DISPLAY, HIGH RESOLUTION, 12V DC / 24V AC
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRONIC SHOCK,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE
AND DO NOT REMOVE COVER OR BACK.
CAUTION:
1. CONNECT 24V AC UL LISTED CLASS 2 POWER SUPPLY.
2. INSTALL CAMERA UNDER UNSTABLE LIGHT SOURCE MAY
CAUSE ABNORMAL FUNCTION.
3. ONLY USE CAMERA UNDER CONDITIONS WHERE
TEMPERA TURES ARE BETWEEN -10°C to 50°C.
ATTENTION:
INSTALLATION SHOULD BE MADE BY A QUALIFIED SERVICE
PERSON AND SHOULD CONFORM TO ALL LOCAL CODES
1. General
This color CCD video camera employs a solid-state imaging device with 470 / 410K or
310 / 270K picture elements. This unit is equipped with a newly developed DSP (Digital Signal
Processor) for processing the video signal.
This camera has dynamic range 400:1, surveillance under various critical backlighting
environments are always possible. The camera uses Sony’s new double speed CCD. Its
dynamic range allows processing to be over 52dB.
2. Features
z 1/3” SONY Wide Dynamic Double Speed CCD , Super HAD with 470K / 410K (PAL / NTSC) pixels,
10bit A/D Digital Signal Process (DSP)
z Hyper Dynamic Range 400:1
z Highest Dynamic Range up to 52dB and real time video output 30 fps
z 6 Preset modes and 1 Customized mode setting are available for various environments
z For subject requiring special protection due to privacy concerns, 8 masks can be shown on the
screen by using OSD Control
z Electronic Frame Integration from 2x ~ 160x sense up
z Advanced On-Screen Display (OSD) control
z Versatile exposure system WD mode, Flick-less, Normal auto iris
z Outstanding signal to noise ratio better than 50dB
▲ IR accuracy: Vivid color performance in the day time and sharp B/W image with no focus shift in the
nighttime
▲ Smart Optical Low Pass Filter (OLPF) switching mechanism allows changing between color and
monochrome
▲ Enhanced (OLPF) control system (4 modes)
■ Automatic
■ Manual
■ Schedule
■ External 1/O
▲ Integration GPIO (day/night, IR projector control)
▲ On-Screen Display control (OSD)
z Remote control by RS232C
z Internal or Line-lock external Sync
z Isolated switching power 12V DC / 24V AC, AC85 ~ 265 V
- 2 -
3. Name of Parts and Functions
A
J
K
L
I
F
12V DC / 24V AC MODEL
G
E
C
H
A. C (CS) mount adapter if a CS mount lens is to be used, remove the C mount ring
B
D
B. Holder screw hole
Standard photographic pan-head screw size (1/4” – 20) Flange focal lock screw
C. Flange focal lock screw
D. Flange focal distance adjuster—adjust this ring when back focus adjustment is needed.
E. Auto iris lens connector (MINI JACK)
Use with accompanying auto iris lens control connector plug.
Auto iris lens has built-in EE amp. (VIDEO Type)
Set the lens selector to "VD” position.
Connector cable leads
Thumbwheel locking screw
and provided screwdriver
Back focus
thumbwheel
- 3 -
1.Red --- power 3.White --- video
2.NC 4.Black --- shielded
Auto iris lens without EE amp. (DC Type)
Set the lens selector to “DD” position.
Connector cable leads
1. Damping coil (-) 3. Driving coil (+)
2. Damping coil (+) 4. Driving coil (-)
F. Video output terminal (BNC)
This connector is used to connect with VIDEO IN connector of monitor.
G. On-Screen Display keypad
H. Slide out for control panel
I. Power pilot LED
J. 12V DC / 24V AC Block Terminal
This terminal accepts DC 12V (Non-polarity) or 24V AC.
The other model: 85 ~ 265V AC.
K. OSD Remote control connector (MINI JACK)
L.
The Device for sensing brightness level (for D/N function).
12V DC/24V AC MODEL
4. USER OSD SETTING
SETTING SWITCHES AND FUNCTIONS
1.UP button –This button is used to move the cursor upwards. Use
this button to select item.
2.LEFT button –This button is used to move the cursor left. Use to
select or adjust the parameters of the selected item.
3.RIGHT button –This button is used to move the cursor to the right.
Use to select or adjust the parameters of the selected item.
4.DOWN button –This button is used to move the cursor downwards. Use this button to select
item.
5.ENTER button – Press this button to display the setting menu, if the selected item has its own
menu; press this button to enter sub menu.
PC control
For Windows 95/98/ME/2000/XP
1. Insert the floppy into diskette drive
2. Execute OSD_CONT.EXE
3. A keypad icon will be displayed on the screen
4. Use mouse to point the icon for on-screen-display setting
- 4 -
RS-232 Connection Please refer to the Setup option
In the program window (com2 default)
1. RX pin----SD (D-sub 9) pin 3 from PC
2. TX pin----RD (D-sub 9) pin 2 from PC
3. NC
4. GND------GND (D-sub9) pin 5
1/O port The port can send or received signal by external device.
Select option mode by OSD D/N function
The camera can switch day or night by external device when it select
External mode.
And other mode can send signal to external device. Day (oV0, Night (+5)
5. SETTING MENU AND FUNCTIONS
SETUP MENU
CAMERA ID OFF
SENSE UP OFF
LIGHT CNTL WD MODE
WHITE BAL ATW
PICTURE VIDEO
FOCUS ADJ
MISC
END INIT ↑ UNLOCK
1. Press the ENTER key to enter main menu
2. Press UP/DOWN key to select the item for
adjustments
3. Press ENTER key to enter the sub menu of selected
item
4. Move cursor to END at the bottom of the screen and
press the ENTER to close the setup menu and return
to normal camera operation mode
5. Move cursor to INIT and press ENTER to return all parameters to the factory default settings
(Don’t press INIT unless it is necessary)
6. Move cursor to↑position and press ENTER key for menu position setting
7. Move the cursor to UNLOCK and press the ENTER to LOCK the setup menu
Note: If no button is pressed for 2 minutes while any setting menu displayed, all modified data
will be stored and camera will return to the normal camera picture mode
UNLOCK PASSWORD
Press UP, DOWN, DOWN, RIGHT then ENTER key to unlock the menu.
- 5 -
Loading...