OKIN Refined Electric Technology RF3011A User Manual

Page 1
Issue Department:Bedding Division Date
2017-8-15
System Instruction
Instruction of RF3011A
Instruction of RF3011A
Author
Edition
Page 1 of 5
1.1
Figure1buttonofremote
Page 2
Issue Department:Bedding Division Date
2017-8-15
System Instruction
Instruction of RF3011A
Author
Edition
Page 2 of 5
1. Item
1.1 ZG buttonbutton 1 in figure 1
Click the ZG button, the actuator moves to ZG position, stop when click any button during the movement; Press and hold the ZG button for 5s, timer LED of remote flashes, the control box records current position as ZG position; When in the process of moving to memory positions, the head and foot actuators move first, then the tilt and lumbar actuators move;
1.1
1.2 AntiSnore buttonbutton 3 in figure 1
Click
AntiSnore
during movement Press and hold current position as
When in the process of moving to memory positions, the head and foot actuators move first, then the tilt and lumbar actuators move;
button, actuators move to
AntiSnore
AntiSnore
button for 5s, timer LED of remote flashes, the control box records
position;
AntiSnore
position, stop when click any button
1.3 TV/PC buttonbutton 4 in figure 1
Click
TV/PC
movement Press and hold current position as
When in the process of moving to memory positions, the head and foot actuators move first, then the tilt and lumbar actuators move;
button, actuators move to
TV/PC
button for 5s, timer LED of remote flashes, the control box records
TV/PC
position;
TV/PC
position, stop when click any button during
1.4 Childlock buttonbutton 5 in figure 1
In unlocked state, press and hold the childlock button, the red backlight of children lock button begins to flash, after 5s, the red backlight stops flashing, remote entersl into locked state; Under locked state, press any button except childlock button, the red backlight of childlock turns on, the button you pressed is invalid;
Page 3
Issue Department:Bedding Division Date
2017-8-15
System Instruction
Instruction of RF3011A
Under locked state, press and hold childlock button, red backlight of childrenlock begins to flash,after 5s, the red backlight stops flashing, remote enters into the normal working condition;
Author
Edition
Page 3 of 5
1.5 LOUNGE buttonbutton 6 in figure 1
Click
LOUNGE
during movement Press and hold current position as
When in the process of moving to memory positions, the head and foot actuators move first, then the tilt and lumbar actuators move;
button, actuators move to
LOUNGE
LOUNGE
button for 5s, timer LED of remote flashes, the control box records
position;
LOUNGE
position, stop when click any button
1.1
1.6 Reset all memory positions to default settingsbutton 1 and 11 in figure 1
Pressa and hold ZG+FLAT buttons remote flashes, the control box reset all memory positions to default settings
button 1 and 16 in figure 2for
5s, timer LED of
1.7 Head upbutton 7 in figure 1
Press and hold
released
HEAD UP button of remote, head actuator moves out, stop when
1.8 Head downbutton 10 in figure 1
Press and hold HEAD DOWN button of remote, head actuator moves in, stop when released
1.9 Foot upbutton 8 in figure 1
Pressa and hold FOOT UP button of remote, foot actuator moves out, stop when released;
1.10 foot downbutton 9 in figure 1
Press and hold FOOT DOWN button of remote, foot actuator moves in , stop when released
Page 4
Issue Department:Bedding Division Date
2017-8-15
System Instruction
Instruction of RF3011A
When moving to flat position, lumbar actuator and tilt actuator move first, after 500ms, head and
foot actuators start moving;
Author
Edition
Page 4 of 5
1.1
1.11 Flatbutton 11 in figure 1
Click FLAT button, the bed goes flat, stop when click any button during the process of going flat
FCC Waring
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
ISED RSS Warning:
This device complies with Innovation, Science and Economic Development Canada
licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1)
this device may not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'ISED applicables aux appareils radioexempts de licence. L'exploitation est autorisée aux deux
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
ISED RF exposure statement:
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled
environment.The device has been evaluated to meet general RF exposure requirement.
Le matériel est conforme aux limites de dose d'exposition aux rayonnements énoncés pour fac
un autre environnement.ce dispositif a été évalué à satisfaire l'exigence générale de l'exposition
aux rf.
conditions suivantes:
Page 5
Power Cord AC
Power Supply
(JLDP.10.023.000)
Pair&Power Cord DC
FCC ID: IC:21319-CB1120
Control Box
CB.11.20.01
PCU-CB1120
SYNC.
Remote model
(RF
3011)
FCC ID: PCU-RF3011A IC:21319-RF3011A
1
R5.504.01.250
2
JLDP.10.023.000
3
R5.217.01.013
4
5
CB.11.20.01
6
7
RF
3011A
Power Cord AC Power Supply
Pair&Power Cord DC
1
1
1
Head Foot
Synchronization Cable
Control Box
Motor/(Head&Foot) Remote model
1
2
1
Motor
Loading...