Okina USA EIVD36-42VF, EIVD36-42VFP Operational Manual

EIVD36-42VF
EIVD36-42VFP

Operational Manual

Weatherproof IR Dome Color Camera

4. Insert the cable through the Mounting Base and connect the cable.

FEATURES

Please read the Operational Manual
before attempting to use this product.

z 1/3” Sony Super HAD CCD
z 420 TV Lines
z 36 IR LED
z 3.5mm~8.0mm Vari-Focal Lens
z 0.5 Lux @ F1.2 (0 Lux @ IR “on”)
z IR Distance 82~98ft / 25~30m
z Weatherproof IP65 Rating
z 300~450mA IR LED "on" / 90~110mA IR LED "off"
z 12V DC

INSTALLATION INSTRUCTIONS

1. Unscrew the three mounting screws on the Mounting Ring half way

using the Allen Wrench. Do not unscrew the screws all the way
you have a safe place to store the screws.

, unless

5. Screw the remaining two Mounting Base Unit Screws into the

Mounting Base to secure it on the ceiling/wall. Be sure that all
screws are tightened.

6. Align the Mounting Ring so that the arched area is above the IR

LED light. Make sure the Mounting Ring does not cover any part of
the IR LED light because it will reflect the light back into the
Camera during nighttime.

Yes No

7. Location of the vari-focal lens adjustor.

2. Lift the Mounting Ring off the Mounting Base, making sure that the

three mounting screws do not fall off. Remove the Camera from the
Mounting Base.

3. Screw two of the Mounting Base Unit Screws into the Mounting Base

and onto the ceiling/wall.

DIMENSIONS (Unit: mm)

EIVD36-42VF_rev04182008

SPECIFICATIONS

Model EIVD36-42VF EOVD36-42VFP
TV System NTSC PAL
Image Sensor 1/3” Sony Super HAD CCD

DSP Sony
Total Pixels 510(H) x 492(V) 500(H) x 582(V)
Video Output 1 Vp-p 75 Ω (Sync Negative Polarity)
Resolution 420 TV Lines
Minimum

Illumination

0.5 Lux @ F1.2 (0 Lux @ IR “on”)

S/N Ratio More than 48dB
Electronic

Shutter Speed

1/60~1/100,000sec 1/50~1/100,000sec

Synchronization Internal
Gamma Control 0.45
Gain Control Auto
White Balance Auto
Back Light

Compensation

On/Off Switchable

IR LED 36 IR LED
IR Wavelength 850nm
IR Working

Distance

82~98ft / 25~30m

Lens 3.5mm~8.0mm Vari-Focal Lens
IP Rating Weatherproof IP65
Power Supply 12V DC
Power

Consumption
Operation

Temperature

300~450mA IR LED "on"

90~110mA IR LED "off"

o

-10

C ~ +50oC

Dimension 130mm(D) x 100mm(H)
Weight 1100g

* Specifications subject to change without notice

FCC NOTICE:

This equipment has been tested and found to comply with the limits
for a class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a
commercial environment. This equipment generates radio frequency,
and if not installed and used in accordance with the instruction
manual, may cause harmful interference.

ADDITIONAL CAUTIONS:

z Be careful not to shake the camera.
z Please avoid places where direct sunlight may shine on the

camera.

z Please avoid places where there are frequent vibrations or

shocks.

z Please avoid places where the temperature exceeds 50

temperatures lower than -10

o

C.

o

C or

z Please avoid storing and operating the camera in water.
z Please avoid water spills on the video connectors and the DC jack

connectors.

SPECIFICATIONS

z One (1) EIVD36-42VF Camera with power/video cable

- One (1) Camera

- One (1) Mounting Ring

- One (1) Mounting Base

z Four (4) Mounting Base Unit Screws
z Four (4) Wall Anchors
z One (1) Allen Wrench
z One (1) Operational Manual

CAUTIONS

1. Never point the camera toward the sun

Do not expose the lens directly to the sun or to strong light as this may

damage the pick-up device.

2. Handle this camera with care
Avoid any shock or bumping of the camera. Improper handling could

damage the camera.

3. Requires a proper operating environment
This camera is designed for outdoor or indoor use. The allowable

temperature range for operation of this camera is between

-10°C ~ 50°C and the allowable humidity is 85%RH maximum.

4. Clean the front face to the pick-up device
It is recommended that the pick-up device surface be cleaned before

lens installation or whenever the lens is changed. Cleaning should be
done by using a chamois, a very fine soft cloth, lens tissue, or cotton
tipped applicator and ethanol to carefully remove any fingerprint or
dust.

5. Check the power source voltage
The power source voltage should be within the specified range.

(Camera must meet the specifications). Camera must be connected to
a surge protector at all times.

6. Objects and liquid entry
Never push objects of any kind into this camera as this may touch

dangerous voltage points of short out parts that could result in a fire
or electric shock. Never spill any kind of liquid on the video product.

7. Servicing
Do not attempt to service this video product by yourself as opening or

removing covers may expose you to dangerous voltage or other
hazards. Refer all service to qualified servicing personnel.

8. Damage requiring service
Unplug this video product from the wall outlet and refer service to

qualified servicing personnel under the following conditions:

a. When the power supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the video

product.

c. If the video product has been dropped or the cabinet has been

damaged.

d. When the video product exhibits a distinct change in

performance.

WARRANTY

This product is covered under warranty for one year from the date of
purchase. The warranty will automatically be voided if any of the
following occurs:

1. Camera sticker is removed

If the camera sticker is removed, we will not be able to conf irm any

information regarding when and where the product was purchased.
We have no other way to verify the purchase record without the serial
number on the camera sticker; therefore, it should not be removed.

2.

Camera is modified in any way

If the camera is scratched, damaged, or modified in a manner not

described in this manual, the warranty will be voided immediately. It is
the customer’s responsibility to keep the camera in good condition.

3.

Video or power cable is cut

The video cable and the power cable should not be tampered with.
Cutting or modifying of the cables will result in termination of the
warranty.

EIVD36-42VF_rev04182008