Oki Teriostar LP-2060-MF Quick Reference Guide

Wide Format Printer

Teriostar LP-2060 Series

Multifunction Model

LP-2060-MF

Quick Reference Guide

U10000088500 Dec ember, 2017 Rev. 2

Preface

Your Printer is a Teriostar LP-2060 Series Wide Format Printer.

This manual describes the basic operation methods for this model.

For more detailed information, see the User's Manuals on the supplied CD-ROM.

Keep this guide in a place where you can easily read it when required.

Table of Contents

Turning the Power On/O …………………… 3

Power On ……………………………………………… 3

Power O ……………………………………………… 3

Mode Buttons ………………………………… 3

Replacing the Paper …………………………… 4

Replacing the Toner Cartridge ………………… 6

Replacing the Waste Toner Bottle …………… 8

Replacing the Charger Unit …………………… 10

Replacing the Process Cartridge ……………… 12

Part Names ……………………………………… 14

Paper Jams ……………………………………… 16

Copying ………………………………………… 20

Importing Images (Documents) to a Computer

… 21

Operating the Printer from a Computer ……… 23

Troubleshooting ……………………………… 24

When an Error Message Appears …………………… 24

Smears on a Printout ……………………………… 24

Changing the Time Until Power Save Mode ……… 24

Automatic Paper Cutting After a Certain Time …… 24

Automatic Paper Cutting After Opening

and Closing a Door ………………………………… 25

Changing the Print Density ………………………… 25

Wrinkles on Tracing Paper ………………………… 25

Selecting Paper to Match the Print Data …………… 25

Missing Print or Slow Data Reception ……………… 26

Service Representatives ……………………… 29

Disposal Method …………………………………… 29

Turning the Power On/Off

Power On

12

Power O

1

Press down for

1 sec. or longer

2

Mode Buttons

zCOPY button

Changes to copy mode, and the lamp at the button's

left lights up. For more details, see the separate User's

Manual for Multifunction Printer Operation.

zSUBMIT button

Changes to submission mode, and the lamp at the

button's left lights up. For more details, see the separate

User's Manual for Multifunction Printer Operation.

zSCAN button

Changes to scan mode, and the lamp at the button's

left lights up. For more details, see the separate User's

Manual for Multifunction Printer Operation.

zPRINT button

Changes to print mode and enables printing.

zMENU button

Changes to menu mode, which enables the Printer

setting specication.

3

Replacing the Paper

2

1

5

6

3

4

OkNo

7

4

TReplacing the Paper

8

60 cm
(23.63 inches)

10

11

Approximately 90°Approximately 90°

9

5

Replacing the Toner Cartridge

2

1

4

x10

x10

5

3

6

6

7 8

Disposing of Empty Toner Cartridges

TReplacing the Toner Cartridge

Put the used toner cartridge into the bag provided in the box of the new toner cartridge, and dispose

of it according to the local regulations.

7

Replacing the Waste Toner Bottle

x10

1 2

3

①

②

4

8

TReplacing the Waste Toner Bottle

5

6

7

①

②

Disposing of Used Toner Bottles

Dispose of the waste toner bottle according to the local regulations.

9

Replacing the Charger Unit

Press do

1

wn for

1

2

sec. or longer

5

6

3

4

7

10

8

TIP

9

10

TReplacing the Charger Unit

11

The charger unit can be installed in

either direction.

If lines or other defects appear on

the printout, inverting the charger

unit right and left sides may solve the

problem.

11

Replacing the Process Cartridge

Press do

1

wn for

1

2

sec. or longer

5

6

3

4

7

8

9

12

10

①

②

11

TReplacing the Process Cartridge

③

14

12

15

①

13

②

①

③

②

13

16

Part Names

Front Side

Toner door

Scanner cover

Document table

Front door

Drawer for rolls 1 and 2

Drawer for rolls 3 and 4

14

Rear Side

TPart Names

Paper outlet slot

Latch button

Fuser unit drawer

Filter cover

Waste toner door

Process cartridge drawer

Paper outlet cover

15

Paper Jams

The door requiring action is displayed, in

accordance with the paper jam location.

Open the specied door and take the appropriate

action to remove the paper jam.

Paper jam in a Roll paper drawer

1

3

2

Paper jam in the front door

1

16

TPaper Jams

2

3

2

When you cannot pull out the paper
easily:

②

①

Paper jam in the Fuser unit

1

3

17

TPaper Jams

Paper jam in a roll paper drawer or front

door

3

2

1

4

5

18

6

TPaper Jams

7

8

2

3

4

Original jam

1

5

19

Copying

Press COPY

Set the original

Position the original facing down. Set it in the Printer

aligned with the original width guide. The inserted original

is automatically pulled into the Printer, and set.

20

Importing Images (Documents) to a Computer

Double-click TerioStation2.

1

Click the Scan tab.

2

Click Save Folder.

3

4

5

Select the destination folder to save the scanned

data. Click OK.

Click Scan.

21

TImporting Images (Documents) to a Computer

6

7

Click Preferences.

Input the Printer IP address in the Assign host

name/IP address eld. Click OK.

Set the scan conditions, and then click Scan.

8

Load the original.

9

Important

If "Scanner is operating in another mode" is displayed, press SCAN on the operation panel.

22

Operating the Printer from a Computer

Start the web browser and enter "http://(IP address set on the Printer)" in the

1

address eld. Press Enter.

Click English.

2

Click an item from the left menu to check the settings or Printer status.

3

23

Menu

Menu

Troubleshooting

When an Error Message Appears

Take the action specied by the panel message.

Or see the User's Manual for Basic Printer

Operation, Chapter 4.

Smears on a Printout

Replace the process cartridge. (& page 12)

Changing the Time Until Power Save Mode

Set Time Before Power Save in the Printer Engine

menu.

Printer Engine

Time Before Power Save

Automatic Paper Cutting After a Certain Time

Set Top Cut Timer in the Printer Engine menu.

Printer Engine

Roll 1 Top Cut Timer

or

Roll 2 Top Cut Timer

or

Roll 3 Top Cut Timer

or

Roll 4 Top Cut Timer

O

or

15 minu te s

or

30 minutes

or

60 minutes

or

90 minutes

or

235 minutes

30 minutes

or

1 hour

or

2 hours

or

4 hours

or

1 minute

or

5 minutes

or

10 minutes

24

Menu

Menu

Menu

Menu

TTroubleshooting

Automatic Paper Cutting After Opening and Closing a Door

Set Top Cut at Door Open to On in the Printer

Engine menu.

Printer Engine

Top Cut at Door Open

On

Changing the Print Density

Set Print Density in the Printer Engine menu.

Wrinkles on Tracing Paper

Set Humidity for Tracing Paper to High Humidity

in the Printer Engine menu.

Printer Engine

Humidity for Tracing Paper

High Humidity

Selecting Paper to Match the Print Data

Select Optimal at Paper Supply Mode.

Printer Engine

Print Density

Low

or

Slightly Low

or

Normal

or

Slightly High

or

High

PDL settings

Select the port and format

Paper Parameters

Paper Supply Mode

Optimal

25

TTroubleshooting

Missing Print or Slow Data Reception

Change the driver settings.

In Start Menu, open Devices and Printers.

1

Click Change in the operation mode of

4

the driver.

Change the output process selection from

5

Process with Printer to Process with

Computer. Click OK.

Right-click the OKI LP-2060 icon, and

2

then click Printing Preferences.

Click the Options tab.

3

Click Apply.

6

26

TTroubleshooting

Click OK.

7

Print.

8

If the symptom persists, perform the

following setting operation.

If the problem persists:

Perform steps 1 to 4 and open Driver

1

Operation Mode.

Set the resolution of the printer driver to

2

200dpi or 100dpi. Click OK.

27

TTroubleshooting

Click Apply.

3

Click OK.

4

Print.

5

The User's Manuals and driver are on the supplied CD-ROM.

28

Service Representatives

OKI Data Infotech oers support to ensure you get the most from your Teriostar LP-2060 Series Printer.

For details, contact your dealer or nearest service representative.

http://www.okidata-infotech.com/distributors/index.html

Disposal Method

Dispose of the used toner cartridges and waste toner bottles according to the local regulations.

29

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.

The CE mark, that shows that the products sold in the EU are conformed to the requirements of EC directive,
is statutorily obliged to be axed to the products.
In each directive, the scope of directive to be applied to equipment is explicitly dened. Our company’s
product LP-2060 series conforms the EMC directive, low voltage directive and RoHS Directive.

Inquiry of CE mark:

OKI Europe Ltd.
Wide Format Division

Siemensstrasse 9 , D-63263 Neu-Isenburg
Germany
Tel: [phone]
Fax: [phone]

OKI Data Infotech Corporation

8 Nakase 1-chome, Mihama-ku, Chiba-shi, Chiba 261-8507, Japan
Phone : [phone]
Fax : [phone]

1-8, Nakase, Mihama-ku, Chiba-shi, Chiba, 261-8507, Japan

TEL: [phone]

U10000088500 December, 2017 Rev.2

Copyright© 2016 OKI Data Infotech Corporation.

All rights reserved.

The contents of this manual may be changed without prior notice.