Oki Teriostar LP-1030-MF, Teriostar LP-1030 Quick Reference Manual

Page 1
Wide Format Printer
Teriostar LP-1030 Series
Multifunction Model
LP-103 0 -MF
Printer Model
LP-103 0
Quick Reference Guide
U00123009604
Page 2
Preface
This manual describes the basic operation methods for both the LP-1030 and LP-1030-MF
models. For more detailed information, see the User's Manuals on the supplied CD-ROM.
Keep this guide in a place where you can easily read it when required.
Table of Contents
Turning the Power On/O …………………… 3
Power On ……………………………………………… 3
Power O ……………………………………………… 3
Mode Buttons ………………………………… 3
Replacing the Paper …………………………… 4
Replacing the Toner Cartridge ………………… 6
Replacing the Waste Toner Bottle …………… 8
Replacing the Charger Unit …………………… 10
Replacing the Process Cartridge ……………… 12
Part Names ……………………………………… 14
Paper Jams ……………………………………… 16
Copying
Importing Images (Documents) to a Computer
………………………………… 22
MF
MF
23
Operating the Printer from a Computer
Troubleshooting ……………………………… 26
When an Error Message Appears …………………… 26
Smears on a Printout ……………………………… 26
Changing the Time Until Power Save Mode ……… 26
Automatic Paper Cutting After a Certain Time …… 26
Automatic Paper Cutting After Opening
and Closing a Door ………………………………… 27
Changing the Print Density ………………………… 27
Wrinkles on Tracing Paper ………………………… 27
Selecting Paper to Match the Print Data …………… 27
Missing Print or Slow Data Reception ……………… 28
Service Representatives ……………………… 31
Disposal Method …………………………………… 31
MF
25
Page 3

Turning the Power On/Off

Power On

12
Power O
1
Press down for
1 sec. or longer
2

Mode Buttons

zCOPY button
Changes to copy mode, and the lamp at the button's
left lights up. For more details, see the separate User's
Manual for Multifunction Printer Operation.
zSUBMIT button
Changes to submission mode, and the lamp at the
button's left lights up. For more details, see the separate
User's Manual for Multifunction Printer Operation.
zSCAN button
Changes to scan mode, and the lamp at the button's
left lights up. For more details, see the separate User's
Manual for Multifunction Printer Operation.
zPRINT button
Changes to print mode and enables printing.
zMENU button
Changes to menu mode, which enables the Printer
setting specication.
MF
MF
MF
3
Page 4

Replacing the Paper

2
1
5
6
3
4
7
4
Page 5
8
7
TReplacing the Paper
60 cm (23.63 inches)
9
10
Paper Cut Position
ロール紙の交換
1
Replacing Roll Paper
᳈ᤶ㒌
用紙カット位置
ߛ㒌ԡ㕂
4
32
6
5
5
Page 6

Replacing the Toner Cartridge

1
3
4
x10
x10
5
2
6
6
Page 7
7 8
TReplacing the Toner Cartridge
Disposing of Empty Toner Cartridges
Put the used toner cartridge into the bag provided in the box of the new toner cartridge, and dispose
of it according to the local regulations.
7
Page 8

Replacing the Waste Toner Bottle

x10
1 2
3
4
8
Page 9
TReplacing the Waste Toner Bottle
5
6
7
Disposing of Used Toner Bottles
Dispose of the waste toner bottle according to the local regulations.
9
Page 10

Replacing the Charger Unit

Press down for
1
2
3
1 sec. or longer
5
6
4
7
10
Page 11
TReplacing the Charger Unit
TIP
8
9
12
The charger unit can be installed in
either direction.
If lines or other defects appear on
the printout, inverting the charger
unit right and left sides may solve the
problem.
10
11
11
Page 12

Replacing the Process Cartridge

Press down for
1
2
3
1 sec. or longer
6
7
8
4
5
9
10
11
12
Page 13
TReplacing the Process Cartridge
12
13
14
15
16
17
18
13
Page 14

Part Names

Front Side
Multifunction Model
Document table
Drawer for roll 1
Drawer for roll 2
Printer Model
Scanner cover
Original output guide
Latch lever
Filter cover
Waste toner door
Drawer for roll 1
Drawer for roll 2
Latch lever
Filter cover
Waste toner door
14
Page 15
Rear Side
TPart Names
Printer ModelMultifunction Model
Rear door
Toner door
Fuser unit drawer
Toner door
Rear door
Process cartridge drawer
Paper outlet cover
15
Page 16

Paper Jams

The door requiring action is displayed, in
accordance with the paper jam location.
Open the specied door and take the appropriate
action to remove the paper jam.
Paper jam in a Roll paper drawer
2
1
3
ロール紙の交換
1
Replacing Roll Paper
᳈ᤶ㒌
用紙カット位置
Paper Cut Position
ߛ㒌ԡ㕂
4
32
6
5
7
16
Page 17
Paper jam in the rear door
TPaper Jams
2
1
3
4
17
Page 18
TPaper Jams
Paper jam in the Fuser unit
2
1
3
When you cannot pull out the paper easily:
18
Page 19
Paper jam in a roll paper drawer or
front door
TPaper Jams
2
1
3
4
ロール紙の交換
1
Replacing Roll Paper
᳈ᤶ㒌
用紙カット位置
Paper Cut Position
ߛ㒌ԡ㕂
4
32
6
5
7
19
5
Page 20
TPaper Jams
6
8
Original jam
7
1
MF
2
20
3
Page 21
4
5
TPaper Jams
21
Page 22
Copying
MF
Press COPY
Set the original
Position the original facing down. Set it in the Printer
aligned with the original width guide. The inserted original
is automatically pulled into the Printer, and set.
22
Page 23
Importing Images (Documents) to a Computer
Double-click TerioStation.
1
Click the Scan tab.
2
MF
3
4
5
Click Save Folder.
Select the destination folder to save the scanned
data. Click OK.
Click Scan.
23
Page 24
TImporting Images (Documents) to a Computer
6
7
MF
Click Preferences.
Input the Printer IP address in the Assign host
name/IP address eld. Click OK.
Set the scan conditions, and then click Scan.
8
Load the original.
9
Important
If "Scanner is operating in another mode" is displayed, press SCAN on the operation panel.
If "Color processing is not supported because the scanner being used is a dedicated monochrome
device" is displayed, you cannot scan in color mode.
24
Page 25
Operating the Printer from a Computer
Start the web browser and enter "http://(IP address set on the Printer)" in the
1
address eld. Press Enter.
Click English.
2
Click an item from the left menu to check the settings or Printer status.
3
MF
25
Page 26
Menu
Menu

Troubleshooting

When an Error Message Appears

Take the action specified by the panel message.
Or see the User's Manual for Basic Printer Operation,
Chapter 5.

Smears on a Printout

Replace the process cartridge. (& pag e 12)

Changing the Time Until Power Save Mode

Set Time Before Power Save in the Printer Engine
menu.
Printer Engine
Time Before Power Save

Automatic Paper Cutting After a Certain Time

Set Top Cut Timer in the Printer Engine menu.
Printer Engine
Roll 1 Top Cut Timer
ro
Roll 2 Top Cut Timer
O
or
30 minutes
or
1 hour
or
15 minute s
or
30 minutes
or
60 minutes
or
90 minutes
or
235 minutes
2 hours
or
4 hours
or
1 minute
or
5 minutes
or
10 minutes
26
Page 27
TTroubleshooting
Menu
Menu
Menu

Automatic Paper Cutting After Opening and Closing a Door

Set Top Cut at Door Open to On in the Printer
Engine menu.
Printer Engine
Top Cut at Door Open
On

Changing the Print Density

Set Print Density in the Printer Engine menu.
Menu

Wrinkles on Tracing Paper

Set Humidity for Tracing Paper to High Humidity
in the Printer Engine menu.
Printer Engine
Humidity for Tracing Paper
High Humidity

Selecting Paper to Match the Print Data

Select Optimal at Paper Supply Mode.
Printer Engine
Print Density
Low
or
Slightly Low
or
Normal
or
Slightly High
or
High
PDL settings
Select the port and format
Paper Parameters
Paper Supply Mode
Optimal
27
Page 28
TTroubleshooting

Missing Print or Slow Data Reception

Change the driver settings.
In Start Menu, open Devices and Printers.
1
Right-click the OKI LP-1030 icon, and
2
then click Printing Preferences.
Click Change in the operation mode of
4
the driver.
Change the output process selection from
5
Process with Printer to Process with
Computer. Click OK.
Click the Options tab.
3
Click Apply.
6
28
Page 29
TTroubleshooting
Click OK.
7
Print.
8
If the symptom persists, perform the
following setting operation.
If the problem persists:
Perform steps 1 to 4 and open Driver
1
Operation Mode.
Set the resolution of the printer driver to
2
200dpi or 100dpi. Click OK.
29
Page 30
TTroubleshooting
Click Apply.
3
Click OK.
4
Print.
5
The User's Manuals and driver are on the supplied CD-ROM.
30
Page 31

Service Representatives

OKI Data Infotech oers support to ensure you get the most from your Teriostar LP-1030 Series Printer.
For details, contact your dealer or nearest service representative.
http://www.okidata-infotech.com/distributors/index.html

Disposal Method

Dispose of the used toner cartridges and waste toner bottles according to the local regulations.
31
Page 32
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
The CE mark, that shows that the products sold in the EU are conformed to the requirements of EC directive, is statutorily obliged to be axed to the products. In each directive, the scope of directive to be applied to equipment is explicitly dened. Our company’s product LP-1030 series conforms the EMC directive, low voltage directive and RoHS Directive.
Inquiry of CE mark:
OKI Europe Ltd. Wide Format Division
Siemensstrasse 9 , D-63263 Neu-Isenburg Germany Tel: +49 (0)6102 297 400 Fax: +49 (0)6102 297 50 400
OKI Data Infotech Corporation
8 Nakase 1-chome, Mihama-ku, Chiba-shi, Chiba 261-8507, Japan Phone : +81 43 211 1363 Fax : +81 43 211 8709
1-8, Nakase, Mihama-ku, Chiba-shi, Chiba, 261-8507, Japan
TEL: (043) 211-1369
U00123009604 December, 2015
Copyright© 2015 OKI Data Infotech Corporation.
All rights reserved.
The contents of this manual may be changed without prior notice.
Loading...