Ojeda RVP12SL Installation Manual

Ojeda USA, Inc

460 Southport Commerce Blvd

Spartanburg, SC 29306

864 574-6004 Fax [phone]

INSTALLATION AND OPERATION

MANUAL

RVP10SL, RVP12SL, RVP10, RVP12, RVP27, RV2P40,

Congratulations! You have just purchased the finest commercial

Part Number 100330051

RV2P49, RV3P72

refrigeration available.

•••• www.ojedausa.com ••••

Table of Contents

INSTALLATION AND OPERATION MANUAL ........................................................................ 1

APPLICATION ...................................................................................................................................... 3

PRODUCT REGISTRATION ................................................................................................................ 3

DIRECTIONS FOR STORAGE AND HANDLING THE EQUIPMENT ............................................ 3

STORAGE OF THE EQUIPMENT ................................................................................................... 3

UNCRATING ..................................................................................................................................... 3

MOVING THE EQUIPMENT ........................................................................................................... 3

PLACING AND INSTALLING THE EQUIPMENT ............................................................................ 4

ELECTRICAL REQUIREMENTS ........................................................................................................ 5

POSITIONING SHELVES ..................................................................................................................... 5

PRODUCT LOADING ........................................................................................................................... 6

UNIT OPERATION AND COMPONENTS .......................................................................................... 6

ELECTRONIC TEMPERATURE CONTROL: ................................................................................. 6

PRESCRIPTIONS, PROHIBITIONS AND OTHER USES FOR THE EQUIPMENT ........................ 8

SHELF SPECIFICATIONS .................................................................................................................... 8

MAINTENANCE GUIDELINES .......................................................................................................... 9

TECHNICAL ASSISTANCE ................................................................................................................... 10

You have selected one of the finest commercial refrigeration units made. It is
manufactured under strict quality controls with only the best quality materials available.
Your Ojeda cooler, when installed correctly and properly maintained will give you many
years of trouble-free operation.

WARNING!

USE THIS APPLIANCE FOR ITS INTENDED PURPOSE AS DESCRIBED IN THIS MANUAL

When using electrical appliances, basic safety precautions should be followed, including the following:

 Use this appliance for its intended

purpose as described in this Owner
Manual.

 This refrigerator must be properly

installed and located in accordance with
the Installation Instructions.

 We strongly recommend that any

servicing be performed by a qualified
individual.

•••• www.ojedausa.com • [e-mail] • Pg. 2 ••••

 Do not allow children to climb, stand, or

hang on the shelves in the refrigerator.
They could damage the refrigerator and
seriously injure themselves.

 Do not store or use gasoline or other

flammable vapors and liquids in the
vicinity of this or any other appliance.

 Unplug the refrigerator before cleaning

and making repairs.

CAREFULLY READ THESE INSTRUCTIONS. This manual provides instructions in how to best locate,

Figure 1

operate, and maintain this equipment.
It is recommended to keep this manual for any future reference.

APPLICATION

The RVP series of coolers have a sanitation listing permitting the merchandising of packaged food and
beverage product. The unit must be located in an indoor environment where the ambient must be
maintained less than 90oF/65%RH.

PRODUCT REGISTRATION

Write down the Serial number of your new unit for future reference. The Serial Number is found on the
data plate located on the back of the unit and on the inside top left side of the cabinet.

MODEL: ________________________

SERIAL NUMBER: _______________

DIRECTIONS FOR STORAGE AND HANDLING THE EQUIPMENT

STORAGE OF THE EQUIPMENT

If the equipment will be kept in storage, it is suggested to keep it in its original packing.
In case you need your equipment to be inactive for a long period of time after being used, verify that it
has been unplugged. After cleaning it thoroughly with a damp cloth, lukewarm water and neutral soap
and carefully drying it, cover it with a polyethylene film or similar waterproof material.

UNCRATING

The following procedure is recommended for uncrating the unit:
Remove the outer package by carefully cutting the shrink wrap and removing the 4 corner posts and top
lid.
Inspect for concealed damage. Immediately file a claim with the freight carrier if there is damage.
Move your unit as close to the final location as possible before removing the wooden skid.

MOVING THE EQUIPMENT

The unit is constructed to facilitate using a forklift to handle it. (Fig. 1) Use
this handling means to move the equipment as close as possible to the
location where it will be installed.

IMPORTANT: Never push, pull or strike the front glass.

•••• www.ojedausa.com • [e-mail] • Pg. 3 ••••

Part Number 100330051

PLACING AND INSTALLING THE EQUIPMENT

ENVIRONMENTAL CONDITIONS

THIS UNIT CANNOT BE INSTALLED IN ENVIRONMENTS WITH EXPLOSIVE GASES. THE EQUIPMENT IS

DESIGNED ONLY FOR INDOOR OPERATION.

The unit must be located in an indoor environment where the ambient is
maintained less than 90oF/65%RH.

For the correct performance of the refrigerating system, it is very
important to leave at least 10 cm (4") of free space both at the sides and
back to allow proper air circulation.

The location of the cooler must be kept away from sources of heat and
humidity including direct sunlight, toasters, ovens, coffee warmers, other
appliances condenser air discharge, infrared heaters, or other heat
generating appliances. Keep the unit away from external doors.

The unit should be leveled prior to operation.

The unit must have casters, 6” legs, or sealed to the floor per NSF guidelines.

•••• www.ojedausa.com • [e-mail] • Pg. 4 ••••

Part Number 100330051

ELECTRICAL REQUIREMENTS

Model

Voltage

(V)

Current

(A)

Circuit

Required (A)

RVP10SL, 12SL, 10, 12

120

5.7

15

RVP27

120

7.5

15

RVP500, RV2P49, RV3P72

120

9.5

15

The power cord of this appliance is equipped with a 3-prong (grounding) plug which mates with a
standard 3-prong (grounding) NEMA 5-15R type wall outlet to minimize the possibility of electric
shock hazard from this appliance.

The use of extension cords is not permitted and will void the warranty.

Before connecting your equipment, check that the electrical data on the data plate match your electrical
output.

IMPORTANT NOTICE: PLUG THE EQUIPMENT INDEPENDENTLY TO A LOAD CENTER WITH AN

APPROPRIATE CIRCUIT BREAKER ACCORDING TO THE NAMEPLATE AMPS.

POSITIONING SHELVES

The shelves and holders have been fixed to the inside floor of
the unit to prevent their loss during transportation.

Insert the shelf clips in the pilaster notches making sure they are
at the same level such that the shelves remain horizontal.

IMPORTANT: The products on each shelf must leave three to
five centimeters of free clearance between them and the next
shelf in order to allow proper air circulation.

•••• www.ojedausa.com • [e-mail] • Pg. 5 ••••

Part Number 100330051

PRODUCT LOADING

The RVP series of units are not intended to be a pull down refrigerator and as such the product must be
loaded at their intended merchandising temperature.

Before loading products, allow the equipment to operate empty for at least two
hours.

When loading products:

- Do not block the lower ventilation grille with the packages about to be loaded.

- Do not over hang the shelf.

- Do not press the product against the rear wall

- Never exceed the shelf weight limits

UNIT OPERATION AND COMPONENTS
ELECTRONIC TEMPERATURE CONTROL:

The unit is provided with an electronic temperature control that controls the operation of the unit based
on the temperature of the air discharging from the evaporator at the back of the unit.

In order to achieve the desired product temperature, the electronic control is factory adjusted to turn off
the refrigeration system at 28ºF and start it at 39ºF.

When you plug the unit in, the control display will
illuminate. However, there is a start-up delay of 2
minutes before the compressor(s) are energized. This
delay avoids the possibility that during a power failure
the compressors are forced to restart before the
refrigerant pressures are equalized.

The control has been factory-adjusted with a defrosting
cycle that is scheduled to ensure that the evaporator
performs without any ice build-up.

None of the factory-programmed electronic control parameters can be modified unless an access code is
entered (only your distributor's technical personnel have that code).

•••• www.ojedausa.com • [e-mail] • Pg. 6 ••••

Part Number 100330051

COMPRESSORS:

The one and two door RVP units have single hermetic compressors. The RV3P72 has two hermetic
compressors that start in two steps with a delay of 10 seconds to reduce the in-rush of current to the unit.

CONDENSERS:

The RVP series of units incorporate a "maintenance free" condenser design in the refrigeration system
which reduces the need for the regular cleaning process that fin and tube condensers require. Besides the
savings in preventive maintenance costs, energy expenses will be stable throughout long periods of time
since the condensers will remain "clean and unobstructed".

EVAPORATOR:

In the event it is believed that the unit has had a “freeze up” condition due to operation of the unit in

high temperature or humidity conditions the evaporator can be thawed by emptying the cabinet of
product and removing power until the coil is clear.

CONDENSATION EVAPORATOR TRAY:

When the equipment operates, condensed water from the environment is collected on the evaporator.
During each off-cycle, the water drains to the evaporator tray located at the bottom of the unit where it is
evaporated using the heat from the refrigeration system.

SLIDING CONDENSING UNIT:

The condensing unit can be pulled out, sliding it approximately 40 cm (16") to allow servicing the
condenser motor(s), compressor(s) and electrical components. In order to service the condensing unit,
remove the two screws that hold the lower front grill (one at each side). Remove the screws that hold the
front bracket that clasps the condensing unit and slide it gently out to have access to the components you
want to check.

Once completed, every component must be returned to its original location for proper operation.

LIGHTING:

The lamp can be turned off with the switch located at the left side of the upper section, near the lamp.

•••• www.ojedausa.com • [e-mail] • Pg. 7 ••••

Part Number 100330051

PRESCRIPTIONS, PROHIBITIONS AND OTHER USES FOR THE
EQUIPMENT

The equipment has been exclusively designed to maintain the proper
temperature of packaged fresh food and beverages. Because the unit is
not designed to cool the product down quickly, the product must be
loaded at its appropriate temperature.

Displaying pharmaceutical products in this unit is prohibited.

CAUTION

- Do not remove grilles or panels that require using tools to be accessed

- Do not keep the unit running unloaded. UNPLUG IT when you are not
planning to use it.

Using any electrical or electronic equipment entails the compliance with some fundamental rules.

- Do not touch the unit with wet hands or feet.

- Do not install the equipment outdoors.

- Do not remove or ignore safety devices.

- Do not leave objects on top of the unit.

- Do not climb on top of the unit.

- Never use direct or indirect water jets on the unit

- Do not allow the electronic control to be adjusted by customers or
unqualified personnel. For any adjustment you must contact your
distributor.

- Verify that the hot air stream from the condenser towards the back of
the unit is not directed to other refrigeration units, which would
compromise their operation.

- Under no circumstance should you block the front grille of the unit.

THE MANUFACTURER DOES NOT ASSUME ANY RESPONSIBILITY ARISING FROM
DAMAGES CAUSED BY IMPROPER, INCORRECT, OR ERRONEOUS USE.

It is important to instruct the user on the operation of the equipment according to this instruction manual,
and to make sure that said manual is within reach of any operator that might use the unit.

SHELF SPECIFICATIONS

The shelves have been designed to withstand the rigors of normal use and loading capacity not to exceed
40 pounds per square foot evenly distributed weight per shelf:
This load limits must not be exceeded to prevent potential damage to the shelf and/or injury to users.

•••• www.ojedausa.com • [e-mail] • Pg. 8 ••••

Part Number 100330051

MAINTENANCE GUIDELINES

Regularly and carefully cleaning the equipment prevents deterioration and product alteration.

CLEANING THE UNIT

Clean every week with only a damp piece of cloth and neutral soap each
external and internal surface, and dry them with a clean soft cloth

Never use flammable or abrasive products. The unit must never be cleaned

with water jets.
IMPORTANT: During maintenance and cleaning operations, make sure

that good visibility conditions exist in the working area, using other light
sources in case it is needed. Be very careful when working with moving
and/or high-temperature parts.

CLEANING THE CONDENSER COIL

IMPORTANT WARRANTY INFORMATION:

Condensers accumulate dirt and require regular cleaning. Dirty condensers result in

compressor failure, product loss, and lost sales; which are not covered by warranty

If you keep the condenser(s) clean you will minimize your service expense and lower your electrical
costs. The following is a step-by-step guideline for the cleaning of the condenser(s):

1. Disconnect power to the unit.

2. Take off front lower grill assembly by removing the two (2) screws in the top corners.

3. Clean off accumulated dirt from the condenser coil(s) using a vacuum and/or a damp rag.

4. Replace the grill assembly.

5. Connect power to the unit and verify that when required the condensing unit(s) are running.

If you cannot remove the dirt adequately, please call your refrigeration service company.

•••• www.ojedausa.com • [e-mail] • Pg. 9 ••••

Part Number 100330051

TECHNICAL ASSISTANCE

If technical personnel assistance is required, you must immediately contact your distributor, specifying
the kind of problem and clearly indicating the equipment model and serial number. If replacing parts is
required, do it through your distributor.

WARNING: Always ask for original spare parts
AUTHORIZED DISTRIBUTOR:
_____________________________________
COMMERCIAL NAME:
_____________________________________
ADDRESS:
_____________________________________
TELEPHONE:
_____________________________________
E-MAIL:
_____________________________________

•••• www.ojedausa.com • [e-mail] • Pg. 10 ••••

Part Number 100330051