Ohsung Electronics URCGEN2CP1 User Manual

Order Number

: GETEC-C1-13-307

FCC Part 15 subpart B

Test Report Number

: GETEC-E3-13-075 Page 1 / 1

APPENDIX G

: USER’S MANUAL

EUT Type: CENTRAL PROCESSOR

FCC ID.: OZ5URCGEN2CP1

Owner’s Manual

CP-1

Central Processor

ccGEN2 CP-1 Owner’s Manual ©2013 Universal Remote Control, Inc.

The information in this owner’s manual is copyright protected. No part of this
manual may be copied or reproduced in any form without prior written consent
from Universal Remote Control, Inc.

UNIVERSAL REMOTE CONTROL, INC. SHALL NOT BE LIABLE FOR
OPERATIONAL, TECHNICAL OR EDITORIAL ERRORS/OMISSIONS MADE IN
THIS MANUAL.

The information in this owner’s manual may be subject to change without prior
notice.

ccGEN2 is a registered trademark of Universal Remote Control, Inc.

URC - Control the Experience is a registered trademark of Universal Remote
Control, Inc.

All other brand or product names are trademarks or registered trademarks
of their respective companies or organizations.

Universal Remote Control,Inc.

500 Mamaroneck Avenue, Harrison, NY 8528

Phone: [phone] Fax: [phone]

TABLE OF CONTENTS

Introduction 1

Features and Benefits 1

Parts Guide 1

Front Panel Descriptions 2

Rear Panel Descriptions 3

Installing the CP-1 4

Specifications 8

Limited Warranty Statement 9

End User Agreement 11

Federal Communication Commission
Interference Statement 12

Declaration of Conformity 13

Page 1

CCGEN2 CP-1 ADVANCED NETWORK SYSTEM CONTROLLER

Introduction

Congratulations on purchasing the ccGEN2 CP-1 Central Processor
for automation and control. Using the ccGEN2 line of interfaces
provides you full access and control for every compatible device
using IR, IP, RS-232, and Relays. This network based control is also
compatible with URC sensors, like audio sensor and video sensor,
which detects the status of a device and provides automation triggers.

The CP-1 makes it easy to turn on multiple devices at once like a
TV and Blu-Ray, even lights with one button press. Enjoy
controlling your space!

Features and Benefits

l Stores and issues commands and macros for all IP, IR,

RS-232, Relay to compatible devices and other ccGEN2
series base stations in the system.

l Provides two-way communication with ccGEN2 rinterfaces.

(RM-1 remote requires optional AZ-1 to be compatible with
CP-1)

l Control URC Lighting with an optional RFTX-1 RF Transmitter.

l Can be programmed off site via the internet.

Parts Guide

The CP-1 Advanced Network System Controller includes:

1 - Central Processor
1 - Special Emitter for RFTX-1 port
1 - Wall Mount and 4 Screws
1 - AC Power Adapter

6 - Standard Emitters
1 - Adjustment Tool
1 - Installation Manual

Page 2

CCGEN2 CP-1 ADVANCED NETWORK SYSTEM CONTROLLER

Front Panel Descriptions

The front panel consists of two indicator lights which illuminate
when in use.

Power LED: Indicates that the CP-1 is powered on when lit.

Ethernet LED: Indicates the network connectivity status:

● On = Connected

● Off = Not connected

● Blinking = Attempting to connect.

Power LED Ethernet LED

Page 3

CCGEN2 CP-1 ADVANCED NETWORK SYSTEM CONTROLLER

Rear Panel Descriptions

The rear panel ports are:

DC 12V Power: Attach the included 12V power supply here.

LAN Connection: RJ45 standard Ethernet connection to the

local network.

Relays (NO, NC, COM): Programmable relay to be normally
opened (NO), normally closed (NC) or momentary contact. An
application should require less than 30V/.5A.

RS-232: Two RS-232 ports support Tx(Transmit), Rx(Receive) and
GND(Ground) connections for two-way communication.
Compatible with URC cables RS232F and RS232M.

Sensors: Two sensor ports allow programming of state dependent
and triggered automation macros. Compatible with URC Video
(SEN-VID), Voltage (SEN-VID), Audio (SEN-AUD), Current (SEN­CMF), Light (SEN-LITE), and Contact Closure (SEN-CCLS) sensors.

IR Outputs: Six standard 3.5mm IR emitter ports with individual
output level adjustment screws. Always use the supplied special
emitter with pink connector, in port #6. Plugging a regular emitter

to this port may cause it to damage the unit and prevent it from
operating correctly.

RFTX-1 Port: Connect the included 3.5mm stereo to 3.5mm stereo
to the optional RFTX-1 transmitter and control URC Lighting
products via 418MHz or 433.92MHz wireless RF.

Reset: Press and release to reboot, while pressing and holding for 15
seconds factory defaults the unit.

DC 12V
Power

Relay: NO,

NC, COM

RFTX-1

Reset

RS-232 Ports

Sensors

IR Outputs: #1-6

LAN