Electronic Speed Control
(INCLUDED)
X
Brush 15Turn
Motor (INCLUDED)
LED Edition
2.4G DSSS Technology
3-Channel 2.4G Radio Control System
INSTRUCTION MANUAL
• Before using, read this manual carefully
AUX Channel
Steering Trim
Steering Wheel
TRIM LED
Power Switch
Charging Jack
Bind Switch
Throttle Trim
St. Dual Rate
Throttle Trigger
Battery Box
CAUTION
• To use your Radio with your models correctly and safely, read this manual carefully and keep it in a
safe place for future reference.
Warning:
1. This product is only equipped for radio controlled cars;
2. The usage of this product should be approved by local law or regulations;
3. We will not be responsible for the damages caused by unauthorized modification, adjustment
or replacement of parts on this product;
4. The manual may be altered without prior notice. Please contact us if you have any corrections
or clarifications that should be made in the manual;
• Before turning on the transmitter, make sure the transmitter batteries are fresh. The voltage of the
transmitter batteries is never lower than 9.6V, and please check and confirm that the servos are
all well and properly connected.
• Keep the radio system away from moist, high temperature and strong vibrations. Do not clean radio
with any solvent.
• Make sure antenna does not touch anything when power switch is turned on. Do not leave this radio
in reach of small children.
• Please use this product according to your local laws and regulations, we are not responsible for any
incidents or damages.
Steering Dual Rates Setup
LEFT
POWER
MID
ST.DR
RIGHT
ST.
ST.TRIM
TH.TRIM
NOR
REV
TH.
INC
ST.DR
DEC
ST.D/R SW
•DEFINITION:
Steering Dual Rate (ST. DR): Is the adjustment that allows the dual rate value (maximum
servo travel) to be increased (INC) or decreased(DEC) with in a range of 0% to 100%
of the steering servo. This functions very useful in a race conditions as it allows you to
tailor the steering radius and sensitivity for the current track conditions.
•ADJUSTMENT:
1.Press and hold the “INC” (Increase) button until the LED on the “ST.DR” turn solid
indicating the maximum turning radius or value of 100%.
2.Press and hold the “DEC” (Decrease) button until the LED on the ‘ST.DR” goes dim or out
to reach the minimum turning radius or value 0%.
CHECKING YOUR DUAL RATE
•To Check Your Dual Rate: First turn your radio “ON” then turn “ON” your
vehicle. Check your steering on your radio by turning left and right several
times. Now turn your steering wheel all the way to the left or right whichever
you choose and hold it their while pushing the “DEC” (decrease) button on
the “ST-DR” and hold it down, you should see that the wheel on your vehicle
decrease in radius and that the LED on “ST-DR” will start blinking and slowly
dim. Now to increase the dual rate turn the wheel left or right all the way and
hold it while pushing the “INC” button this will increase the radius of the wheel
and the LED on ST-DR will start blinking slowly and turning solid indicating
that the “Dual Rate” is at 100% . When running your vehicle try to run the
“Dual Rate” at maximum radius (100%). Then if you have too much steering
then decease as needed.
POWER ST.DR
001 %
INC
DEC
ST.D/R
0%
100%
100%
0%
1%00
100%
0%
100%
2.4Ghz Binding
•Press and hold the bind button on the front of the transmitter while
turning ON the power switch button until the (ST.DR) LED Flashes.
STEP 2
Power Switch (turn on)
STEP 1
Bind (Press and hold)
AUX Channel Function (CH3)
Flashing LED
Binding cable
Binding cable
Plug In
Solid LED
2. With the system hooked up as shown, insert the binding cable in
the charging plug receptacle. Turn on the power of the receiver
(4.8 - 5.6V), and now the LED should be flashing indicating
that the receiver is ready to bind.
Receiver
3. The LED should go solid, indicating the system
has connected. Now turn off the receiver and
remove the binding cable.
Receiver
•This switch control the transmitter’s third channel. A servo plugged in this Channel 3 will move to full travel in one direction when
the switch is in the “AUX” position, then move the switch to the “OFF” position the servo will move in the opposite position . This
channel can be use to turn on all sort of things in your vehicle. For example, lights, on board camera etc..... l
Handling Procedure For Batteries
Handling Procedure For Batteries
•Battery Replacement
1) Remove the battery cover from the transmitter by sliding it in the direction of the arrow.
2) Remove the used batteries.
3) Load the new 8 AA size alkaline, or Nickel Metal Hydride (NimH) rechargeable batteries,
and pay very close attention to the polarity marking on the batteries.
4) Slide the battery cover back onto the case.
5) If you use rechargeable batteries OFNA make this charger 10210 it will charge your Transmitter
9.6v at 100mA and Receiver battery 4.8v-6v at 100mA at the same time.
•Caution
Always make sure you reinsert the batteries are in the correct polarity order. If the batteries are loaded
incorrectly, the transmitter may not work or can be damaged.
When the transmitter is not used for a long period of time remember to remove the batteries. If the batteries
do happen to leak, clean the batteries case and contacts thoroughly and make sure the contacts are free of
corrosion.
•Battery Disposal
Some countries and state require special handling of used batteries, please contact the agencies responsible
for recycling hazardous wastes in your local area.
•Battery low voltage alarm indicator. LED Power light will flash.
Receiver Connection Diagram
Specification Data
•Transmitter
NOTICE THE DIRECTION OF BATTERY COVER
10210 - DUAL CHARGER, 4.8V-6V/9.6V TRANSMITTER AND RECEIVER
(Not included)
•Receiver
Channels: 3
Frequency: 2.4Ghz
Power DC: 9.6V - 12V
Measurement: 280 x 190 x 85mm
(Packing Meas.)
Net Weight: 510g
Channels: 3
Frequency: 2.4Ghz
Power DC: 4.8 - 5.6V
Net Weight: 13.5g
Warranty Period
OFNA warranties that the Products purchased (the “Products”) will be free from defects in materials and workmanship at the
date of purchase by the Purchaser.
Limited Warranty
(1) This warranty is limited to the original Purchaser (”Purchaser”) and is not transferable. REPAIR OR REPLACEMENT AS
PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE PURCHASER. This warranty covers
only those Products purchased from and authorized OFNA dealer. Third party transactions are not covered by this
warranty. Proof of purchase is required for warranty claims. Further, OFNA reserves the right to change or modify this
warranty without notice and disclaims all other warranties, express or implied.
(2) Limitations - OFNA MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT NON INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCT. THE
PURCHASER ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY
MEET THE REQUIREMENTS OF THE PURCHASER’S INTENDED USE.
(3) Purchaser Remedy - OFNA sole obligation hereunder shall be that OFNA will, at its option, (1) repair or (2) replace, any
Product determined by OFNA to be defective. In the event of a defect, these are the Purchaser’s exclusive remedies.
OFNA reserves the right to inspect any and all equipment involved in a warranty claim. Repair or replacement decisions
are at the sole discretion of OFNA. This warranty does not cover cosmetic damage or damage due to acts of God,
accident, misuse, abuse, negligence, commercial use, or modification of or to any part of the Product. This warranty does
not cover damage due to improper installation, operation, maintenance, or attempted repair by anyone other than OFNA.
Return of any goods by Purchaser must be approved by OFNA before shipment.
Damage Limits
OFNA SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR
PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCT, WHETHER SUCH CLAIM
IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE, OR STRICT LIABILITY. Further, in an event shall the liability of
OFNA exceed the individual price of the Product on which liability is asserted. As OFNA has no control over use, setup, final
assembly, modification or misuse, no liability shall be assumed nor accepted for any resulting damage or injury. By the act
of use, setup or assembly, the user accepts all resulting liability.
If you as the Purchaser or user are not prepared to accept the liability associated with the use of this Product, you are advised
to return this Product immediately in new and unused condition to the place of purchase.
Safety Precautions
This is a sophisticated hobby Product and not a toy, It must be operated with caution and common sense and requires some
basic mechanical ability. Failure to operate this Product in a safe and responsible manner could result in injury of damage to
the Product or other property. This Product is not intended for use by children without direct adult supervision. The Product
manual contains instructions for safety, operation and maintenance. It is essential to read and follow all the instructions and
warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or injury.
FOR ADDITIONAL HELP YOU CAN CALL OFNA TECH SUPPORT AT (949)586-2910 OR
GO TO WWW.OFNA.COM/GUIDE.HTML FOR HOW TO VIDEO
TO: OFNA TECHNICAL SUPPORT
7 VANDERBILT, IRVINE, CA 92618
TODAY’S DATE: month________day______
1. Print out form.
2. Fill out the form completely.
3. Make a copy of purchase receipt. All replacements/repairs will not be processed,
unless accompanied by proof that item(s) was purchased.
4. Call OFNA technical support at (949)586-2910 for assistance.
1. Your name
____________________________
2. Your address:
____________________________
6. Name of kit / part (on tag or end of box)
_____________________________
7. Kit/part number (on tag or end of box)
_____________________________
8. Purchased from (store name)
____________________________
3. Your Phone Number
(_____)______________________
_____________________________
a. Store phone: (_____) _________
b. _____Item was a gift?
4. Your e-mail address:
____________________________
9. If a part is missing form the kit, circle
the appropriate answers:
5. Summary of your problem (check lines):
a______part(s) is missing from my kit
b______part(s) seems to be defective
c______other problem
a. Yes / No: Is kit box damaged?
b. Yes / No: Factory Seal sticker was secure.
c. Yes / No: I am the original owner.
d. Yes / No: I have contacted the dealer first.
10. Describe your issue fully and include any part numbers:
____________________________________________________________
____________________________________________________________
____________________________________________________________
____________________________________________________________
____________________________________________________________
Failure to fill out this form completely will cause a delay in processing!
11. Affix proof of purchase on second page. All replacement / repairs will not be processed
unless accompanied by proof that item(s) was purchased.
A. If you lost the store receipt, ask the store if they will give you a new one.
B. We do not accepted the following as a substitute: Hand written receipts, ebay transaction numbers/forms or
credit card statements.
Can’t find Proof of Purchase?
12. Send in form with your defective product, as instructed to do by the Ofna
technician,(Name)_________________ you spoke to. Ph:(949)586-2910 Fax: (949)583-9272
B4218 ESC Instruction and Specification
WARNING ELECTRIC MOTOR AND ESC ARE EXTREMELY HOT AFTER
RUNNING, CAN CAUSE SERIOUS INJURY, HANDLE WITH CARE
•Special Features:
1. Exclusive feature for this model. Auto set to neutral position on the throttle. No programming
or adjustment is required. Just one second after powering on the system, the speed control
will beep indicating that is has auto set to the neutral position ( while the speed control is
setting the neutral position do not touch the throttle trigger, leave it at neutral ).
Fig.1
Fig.2
Fig.3
FORWARD
NEUTRAL
BRAKE
AND
REVERSE
2. Thermal Protection Function of The ESC B4218. If the speed control over heats, the Thermal
Protection function will be activated. Once the “TP” is activated, the throttle will rapidly turn
on and off and acceleration becomes erratic. Stop driving immediately, do not drive the car
until the Speed Controller cools down.
3. LED indication, two colors Green/Red
4. Large sturdy aluminum heatsink for maximum heat dispersing.
•Specification:
1. Input Voltage: 6~8.4V 6-7cell Nimh or 2cell Lipo
2. Power IC 150A at (77F), 100A at (212F)
FIG. 4
BATTERY
BLUE NEG
ORG. POS.
3. Supported motor >12T - 27T Mabuchi Motor
4. Factory default Spec: Output Continuous/Peak Current 70A/120A(10sec)
5. Over temperature protection at 200F.
SWITCH
6. BEC Voltage 5V at 1Amp
7. FET internal: forward/reverse...........0.0025/0.005 ohm
RECEIVER WIRE
8. Size:36 x 35 x 30.5mm
9. Weight......53.7g/1.89oz
•Throttle Neutral and ESC setting:
FIG. 5
1. Switch on the transmitter.
2. Set the throttle trim to the middle or the green LED on your Transmitter “TH”
3. Switch on the power of the ESC
4. The ESC will sound 3 beeps (DO RE MI) confirmation, indicating the ESC
is ready & the throttle is at neutral position.
TH.TRIM
•Operating Instructions:
1. Connect the ESC wires to the motor. (Blue is neg and Orange is Positive See Fig. 5)
2. Plug the receiver wire into the throttle or #2 channel on the receiver
3. Ventilation - Mount the ESC in a location that has good ventilation & isolate it from vibration
and shock. Ventilation is extremely important for cooling the ESC & Motor.
4. Plug in your battery, before turning on the ESC, make sure your transmitter is on & the throttle
trigger is at the neutral position. (See Fig 2)
5. Turn on your ESC, the LED light on the ESC will flash red then goes to solid green and a tone
will sound indicating that the ESC is set and ready to go.
FOR ADDITIONAL HELP YOU CAN CALL OFNA TECH SUPPORT AT (949)586-2910 OR
GO TO WWW.OFNA.COM/GUIDE.HTML FOR HOW TO VIDEO
11066
21003
21006
11066
21003
21003
94046
21003
21004
5000wt FRONT DIFF
1000wt REAR DIFF.
21003
21004
21003
21004
11066
21001
11066
21003
21003
21003
94046
11066
21038
21003
21003
21004
21003
21004
11066
21037
5000wt
94034
21005
21005
11065
21002
11065
94002
22012
21015
21014
21002
21007
21007
21014
21016
21015
36870
21012
11066
21017
18075
94043
21028
11066
18075
21017
21017
21029
21029
21029
21123
21009
94004
94043
21009
21028
21029
94043
21029
21123
94004
21121
94005
21121
94005
94003
94002
21018
21018
94003
94002
21124
21018
94005
21018
94005
94003
94004
94004
94041
94003
94041
21154
94003
94033
94034
21018
94033
21153
94034
94033
21018
21028
21029
21029
21033
94041
21078
21011
21028
94041
21078
21033
21078
21033
21033
94033
21033
21033
21034
21033
21078
21033
21033
21033
21036
94002
21127
21036
21023
21023
94005
94004
94019
94004
21017
18075
36870
94041
21059
11066
21026
11066
21027
21025
18075
21128
21017
94019
36870
21059
21123
21029
94004
21029
21123
21024
21028
21021
21029
94043
21021
21124
21122
19031
94038
94003
94002
94004
19031
21122
94041
21023
21022
94005
21023
21022
21018
21018
94005
21018
21018
94033
94034
21018
94002
21018
21127
94003
21126
21143
94005
21143
21143
94019
21128
94041
21133
94019
94019
Assembly of Center Differential Mount
21132
94003
Assembly of Side Guard
21129
94003
94017
21039
94019
21301
94017
94019
94040
94034
(Not Included)
94040
21316 11T
94002
21313
94002
(NOT INCLUDED)
21133
94021
21302
94021
94019
21307
21304
94019
94017
21049
94017
94002
94017
94002
21303
94017
(Not Included)
29076
29076
28081
94008
21130
94003
94002
94002
94008
94003
21036
21048
21048
21036
21228
21228
21228
21228
21138
21228
21067
21138
21138
21044
21067
21067
21144
21066
Shock springs set of 4
21139 Blue Med
21155 White Hard
21139 Blue Med
21155 White Hard
19031
94005
94038
94005
21135
21134
10985
10985
10985
10985
21136
23
OFNA DESCRIPTIONS RETAIL OFNA DESCRIPTIONS RETAIL
11064
BEARING 5x8, 4PCS. 11.95
21131
CENTER DRIVE SHAFT ALUM SC 22.95
11065
BEARING 5x11, 6PCS. 17.95
21132
CENTER DIFF MOUNT ALUM SC 7.95
11066
BEARING 10x15, 4PCS. 15.95
21133
CHASSIS HYPER 10 SC 44.95
11210
SINK ALUM. WASHER 3mm, 16PCS. 7.95
21134
WHEEL, HYPER 10 SC PAIR 8.95
18075
BEARING, 6x13mm. 4PCS. 15.95
21135
TIRES, HYPER 10SC PAIR 19.95
19018
BOOT,SHOCK SHAFT,SILICONE 4PCS 8.95
21136
BODY, CLEAR HYPER 10SC 39.95
19031
BALL,STEEL,SHOCKS 4PCS. 7.95
21137
DECAL HYPER 10 SC BODY 14.95
21001
GEAR, CROWN HYPER 10SC 24.95
21138
SHOCK SHAFT HYPER 10SC 4PCS 12.95
21002
GEAR, PINION HYPER 10SC 12.95
21139
SHOCK SPRING BLUE SET 10SC 15.95
21003
GEAR, DIFF HYPER 10SC 12.95
21140
SHOCK HYPER 10SC PAIR 44.95
21004
DIFF CASE W/GASKET HYPER 10SC 6.95
21141
SCREW SET HYPER 10SC 14.95
21005
DRIVE CUP CENTER HYPER 10SC 11.95
21143
SCREW,3X37mm & 3MM NUT H10SC 2.95
21006
DRIVE CUP F/R DIFF HYPER 10SC 12.95
21144
SHOCK BODY FR/RR HYPER 10SC 27.95
21007
GEARBOX CASE HYPER 10SC 8.95
21153
BUMPER, HYPER 10SC STOCK 6.95
21008
SHOCK MOUNT FR HYPER 10SC 6.95
21154
BUMPER, BRACE HYPER 10SC 6.95
21009
FRONT HINGE PIN HOLDER FR HYPER 10SC
5.95
21301
CNC ALUM MOTOR MOUNT HYPER M/E 34.95
21011
ARM, UPPER FRONT HYP. MINI 6.95
21302
CENTER DIFF UPPER PLATE HME 7.95
21012
ARM, LOWER FRONT HYPER 10SC
9.95
21303
ALUM RADIO TRAY HYPER MINI E 7.95
21014
STEERING KNUCKLES FRONT H.10SC 10.95
21304
BATTERY BOX HYPER MINI E 14.95
21015
PILLOW BALL HYPER 10SC 16.95
21307
VELCRO BATTERY STRAP HME 7.95
21016
CVA, FRONT HYPER 10SC 34.95
21308
SCREW SET HYPER MINI E 7.95
21017
HEX HUB HYPER 10SC 6.95
21316
PINION GEAR 11T-3MM STOCK 12.95
21018
ANTI ROLL BAR SET HYPER 10SC 9.95
22012
FLANGE BALL SET 12.95
21021
HINGE PIN HOLDER REAR H.10SC 5.95
22028
SHOCK REPAIR SET 8.95
21022
ARM, UPPER REAR HYPER 10SC 6.95
22086
SNAP PIN 3.95
21023
TURNBUCKLE, STEERING H. MINI 10.95
28081
ANT.TUBE 1pc.STR.M 4pcs,S 2pcs 2.95
21024
ARM, LOWER REAR 10.95
29076
ANT. MOUNT ALUM. HYPER 9 7.95
21025
UP-RIGHT REAR HYPER MINI 7.95
94041
NUT, 3MM NYLOK 4PCS 1.95
21026
AXLES REAR HYPER MINI 12.95
21027
DOGBONES REAR HYPER MINI 12.95
19363
BALL STUD,SHOCK CNC ALUM, 4PCS 8.95
21028
HINGE PIN SET HYPER MINI 11.95
21155
SPRINGS WHITE HYPER 10SC HARD 15.95
21029
HINGE PIN BUSHING HYPER MINI 4.95
21156
SHOCK TOWER FR GRAPHITE H10SC 24.95
21032
WING POST MOUNT HYPER MINI 6.95
21157
SHOCK TOWER RR GRAPHITE H10SC 29.95
21033
SERVO SAVER SET HYPER MINI 19.95
21158
CENTER GRAPHITE PLATE H10SC 14.95
21034
SERVO SAVER ARM HYPER MINI 6.95
21159
SERVO GRAPHITE PLATE H10SC 9.95
21035
TURNBUCKLE REAR UPPER ARM H.M. 10.95
21160
CNC 7075 FRONT SHOCK TOWER SC 14.95
21036
TURNBUCKLE ENDS HYPER MINI 5.95
21161
CNC 7075 REAR SHOCK TOWER SC 14.95
21037
SPUR GEAR STEEL HYPER MINI 24.95
21162
CNC 7075 HINGE PIN PL FR/RR SC 8.95
21038
CENTER DIFF OUTPUT HYPER MINI 14.95
21163
CNC 7075 HINGE PIN HOLDER FR 8.95
21039
CENTER DIFF MOUNT HYPER MINI 10.95
21164
CNC 7075 REAR HING PIN HOLDER 8.95
21048
TURNBUCKLE STEERING SERVO H.M. 5.95
21165
CNC 7075 CHASSIS HYPER 10SC 54.95
21049
SERVO MOUNT & HORN SET H.M. 10.95
21197
WHEEL, HYPER 10SC WHITE 8.95
21059
HINGE PIN REAR 3x35mm H. MINI 2.95
21198
WHEEL, HYPER 10SC BLACK 8.95
21063
SHOCK BLADDER HYPER 10SC 6.95
21199
CVA DOGBONE ONLY HYPER 10SC 19.95
21066
SHOCK COLLAR THREADED H. MINI 12.95
21281
SHOCK PISTON OPTIONAL HYPER SC 7.95
21067
SHOCK PLASTIC PARTS HYPER MINI 7.95
21306
PINION GEAR 14T-3MM 12.95
21070
SHOCK, REAR SET HYPER MINI 45.95
21311
PINION GEAR 15T-3MM 12.95
21078
BUSHING, 5x8mm HYPER MINI 2.95
21312
PINION GEAR 16T-3MM 12.95
21079
SCREW SET HYPER MINI 19.95
21313
CNC MOTOR HEAT SINK HYPER M/E 19.95
21121
SHOCK TOWER FRONT ALUM SC 9.95
21314
PINION GEAR 12T-3M 12.95
21122
SHOCK TOWER REAR ALUM SC 11.95
21315
PINION GEAR 13T-3MM 12.95
21123
SUSPENSION PLATE F/R SC 6.95
29311
PINION 14T-5MM HYPER 9e 13.95
21124
BODY POST HYPER 10 SC 7.95
29325
PINION 15T-5MM HYPER 9e 13.95
21126
BUMPER, REAR SET SC 14.95
29326
PINION 16T-5MM HYPER 9e 13.95
21127
ARM HOLDER F/R AND BRACE SC 6.95
29328
PINION 17T-5MM HYPER 9E 13.95
21128
CHASSIS BRACE F/R SC 8.95
29329
PINION 18T-5MM HYPER 9E 13.95
21129
SIDE GUARD HYPER 10 SC 13.95
30669
PINION ADAPTOR 5MM TO 3MM 2PCS 8.95
21130
TOP BUMPER HANDLE SC 11.95
81096
FOAM,MOLDED DONUTS,OR/SOFT 6PC 7.95
81097
FOAM,MOLDED DONUTS,YL/MED. 6PC 7.95
1 4 6 1 6 H YP E R 1 0 S C R T R P AR T S L I S T
OPTION PARTS
21001
21121
21015
21026
21126
21002 21009
21003 21123
21004
21005
21006 21127
21011
21012
21016
21017
21018
21122
21021
21027
21028
21029
21124
21143
21016
21037
21038
21039
21132
21133
21129
21130
21007 21014
21154
21022
21023
21024
21025
21033
21034
21035
21036
21048
21023
21128
21131
21138
21063
21144
21066
21128
21049
21049
21079
21304
11066
21281
SHOCK PISTION
21067
21139
Blue Med.
21140
22086
21307
21136
21301
29076
18075
10985
19018
19031
(STOCK)
11210
21141
21316
21314
21315
21313
21155
White Hard
21134
21135
21078
21302
21303
21308
28081
22012
22028
11065
21306
21311
21312
21153
(STOCK)
OWNER’S REGISTRATION CARD
OFNA Racing congratulates you on your purchase of our fine OFNA Product. With proper maintenance and handling this kit will provide many hours of enjoyment.
The registration card should be filled out and mailed to OFNA Racing within 10 days of purchase date.
In the event that the kit is incomplete or component parts are broken due to error in manufacturer, contact your
dealer from which you purchased the kit for replacement part or call OFNA at (949) 586-2910 for your nearest dealer
location. Other items such as radio and engine other covered by individual warranties.
IMPORTANT!
Please print or type, filling in the information listed below and mail immediately
MAIL TO:
OFNA RACING
7 VANDERBILT
IRVINE, CA. 92618
TEL: (949) 586-2910
Write in Your Model Name and Part Number
REGISTRATION CARD
RACER’S NAME TEL:( )
ADDRESS
CITY STATE ZIP
DEALER’S NAME TEL: ( )
ADDRESS
CITY STATE ZIP
OFNA
7 Vanderbilt
Irvine, Ca. 92618
Loading...