Page 1
161 Tadition Trail
Holly Springs, NC 27540
Phone: 800-520-7471
Fax: 919-362-4765
Web Site: www.ofm furniture.com
MOD. Pg6348
A
MOD. Pg6337
D
B
C
A
D
B
C
MOD. Pg6325
D
A
B
C
EASY ASSEMBLY
WITHOUT TOOLS
PATENT PENDING
ASSEMBLY INSTRUCTIONSASSEMBLY INSTRUCTIONS
POLYCARBONATE FLOOR PANEL
8 min
A
T
ASSEMBLY TIME
PATENTE EN TRAMITE
The accessory of panel are inside them
AA
PANEL 63in x 48in......................1 PCS.
GOATEE 5/16 X 3...................... 2 PCS.
BB
WING NUT 5/16........................ 2 PCS.
CC
CORK 5/8..................................2 PCS.
DD
MOD. Pg4748
A
AA
PANEL 47in x 48in.....................1 PCS.
GOATEE 5/16 X 3...................... 2 PCS.
BB
WING NUT DE 5/16.................... 2 PCS.
CC
CORK 5/8..................................2 PCS.
DD
CONT.CONT.
D
CONT.CONT.
AA
PANEL 63in x 37in......................1 PCS.
BB
GOATEE 5/16 X 3..................... 2 PCS.
CC
WING NUT 5/16........................ 2 PCS.
DD
CORK 5/8..................................2 PCS
MOD. Pg4737
B
C
AA
PANEL 47in x 37in.......................1 PCS.
GOATE 5/16 X 3........................ 2 PCS.
BB
WING NUT DE 5/16.................... 2 PCS.
CC
CORK 5/8..................................2 PCS.
DD
D
CONT.CONT.
D
B
A
C
CONT.CONT.
CONFIGURATION B
AA
PANEL 63in x 25in.......................1 PCS.
GOATEE 5/16 X 3...................... 2 PCS.
BB
WING NUT DE 5/16.................... 2 PCS.
CC
CORK 5/8..................................2 PCS.
DD
MOD. Pg4725
A
AA
PANEL 47in x 25in......................1 PCS.
GOATEE 5/16 X 3...................... 2 PCS.
BB
WING NUT DE 5/16.................... 2 PCS.
CC
CORK 5/8..................................2 PCS.
DD
B
CONT.CONT.
D
B
C
CONT.CONT.
If floor panel has a gap between panel
and frame as show in the upper view;
just adjust hooks as show in figure
Panel
Frame
Upper view
X
lift panel enough to assemble
panel hade to frame hook
Frame
X
Close side of hook with
your fingers to adjust panel.
Y
Remove panels, itself between
two people to facilitate the join.
Page 2
11
AA
CONFIGURATION A
MOD. Pg6348
B
Remove panels, itself between
two people to facilitate the join.
22
MOD. POST 47
MOD. Pg4748
PS 63PS 63
D
CONFIGURATION B
FLOOR PANEL MOD Pg4748 FLOOR PANEL MOD Pg4748
FLOOR PANEL MOD Pg4748 FLOOR PANEL MOD Pg4748
FLOOR PANEL MOD Pg4748 FLOOR PANEL MOD Pg4748
FLOOR PANEL MOD Pg4748 FLOOR PANEL MOD Pg4748
UPPER VIEW
D
BB
POST 47POST 47
CONFIGURATION A
UPPER VIEW
FLOOR PANEL MOD Pg4748FLOOR PANEL MOD Pg4748
33
CC
PULL
To hide cables, remove
the complete panels
(G)(G)
Page 3
Rize Panel System
Attach corner connector to
1
frame with screw-in knobs.
Set up frames with corner
connector.
Install cables along frame
4
base through openings.
Pop o grommet and
insert cables.
Align frame with corner
2
connector and screw in
knobs on each side.
Place panel cover hooks into
5
frame hooks. Once wires are
adjusted for length, pop on
grommet covers.
For panel to panel connections;
3
align frames and use smaller
knob, then tighten with
buttery bolt.
161 Tradition Trail,
800-520-7471 (voice)
919-303-6389 (voice)
support@ofminc.com
Holly Springs, NC, 27540
919-362-4765 (fax)
www.ofminc.com
Loading...