Page 1
Model 77366L / 77366R Executive Series L-Shaped Pedestal Desk Return
Parts Listing
B
Side Panel
1 Unit
D
Return
Privacy Panel
1 Unit
A
Return Top
1 Unit
C
Pedestal
1 Unit
E
L-Shaped
Panel Mount
2 Units
Assembly Instructions
Please read all instructions before assembly. Assembly will require 2 people.
STOP
Tools Needed: Allen Wrench and Phillips Head Screw Bit
The following instructions should only be used following the assembly
of a 77366 desk.
Be sure to remove the Pedestal drawers prior to installation.
Step 1: Align Side Panel (B) on the underside of the Return Top (A) by
aligning screw hole brackets with holes in Return Top (A). Insert
6x16mm Screw (H) through Side Panel (B) bracket and into Return
Top (A). Tighten using Phillips Head Screw Bit (J) or screwdriver.
Step 2: Attach Pedestal (C) to underside of Return Top (A) by aligning screw
J
1
H
B
A
Step 3: Attach L-Shaped Panel Mounts (E) to the underside of the Return Top (A). Align screw holes
in L-Shaped Panel Mounts (E) with holes in Return Top (A) and insert 6x30mm Screws (I)
to secure. Tighten using Phillips Head Screw Bit (J) or screwdriver. Slide Return Privacy
Panel (D) onto L-Shaped Panel Mounts (E) and attach by inserting 6x16mm Screws (H) to
secure. Tighten using Phillips Head Screw Bit (J) or screwdriver.
Step 4: Flip the return right side up using at least two people. Line up with the appropriate position
on 77366 Desk. Attach by inserting 6x16mm Screws (H) up through Return Support
Bracket (F) to secure to both the Return Top (A) and the 77366 Desk Top.
Note: At this time, insert drawers back into Pedestal (C) and push all the way in to secure.
holes in Pedestal (C) with holes in Return Top (A), and inserting
6x16mm Screws (H) to secure. Attach Pedestal (C) to Side Panel (B)
by inserting 6x16mm Screws (H) through pedestal wall and into Side
Panel (B). Tighten using Phillips Head Screw Bit (J) or screwdriver.
Cover exposed holes in Pedestal (C) with Screw Cap (G).
F
Return
Support Bracket
1 Unit
H
6x16mm Screw
18 Units
Phillips Head Screw Bit
J
1 Unit
G
Screw Cap
2 Units
I
6x30mm Screw
4 Units
2
H
B
H
G
3
C
I
D
A A
C
Assembly Notes:
During assembly, hand tighten screws only. When all screws
are in place, you may then tighten all screws completely.
CAUTION:
1. Do not use this desk as a step ladder.
2. Check for loose screws and tighten them every 6 months.
06.30.2014
4
H
D
F
E
H
161 Tradition Trail, Holly Springs, NC, 27540
800-520-7471 (voice)
919 -303-6389 (voice)
support@ofminc.com
919-362-4765 (fax)
www.ofminc.com
Page 2
77000 Series How to Remove the Pedestal Drawers
Drawer Removal Instructions
Please read all instructions before you begin.
STOP
All Pedestal Drawers must be removed before attaching the Pedestal to a desk.
Step 1: Stand in front of the pedestal and open the drawer you wish to remove.
Pull drawer all the way out until met with resistance.
Step 2: With both hands, place fingers underneath the open drawer on each side near the
drawer release/locking lever (highlighted below) like you would be picking up the drawer.
Keep hold of the drawer and using just your pointer finger on your right hand and your
thumb on your left hand, simultaneously push the lever UP on the right side
and push DOWN on the left side. While continuing to hold both levers in
the correct pushed position, pull the drawer out.
Step 3: To put the drawer back in, simply align the
rails on the drawer with the tracks on
the pedestal unit and push in.
Push release lever UP
with index finger
on right side.
Place hands here
on each side
of drawer
Push release lever
DOWN with thumb
on left side.
161 Tradition Trail, Holly Springs, NC, 27540
800-520-7471 (voice)
919-303-6389 (voice)
support@ofminc.com
919-362-4765 (fax)
www.ofminc.com
06.18.2014
Loading...